From: Radhey Shyam Pandey <radhey.shyam.pandey@xxxxxxxxxx>
Convert the bindings document for Xilinx AXI Ethernet Subsystem
from txt to yaml. No changes to existing binding description.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xxxxxxxxxx>
Signed-off-by: Sarath Babu Naidu Gaddam <sarath.babu.naidu.gaddam@xxxxxxx>
---
Changes in V7:
1) Addressed below review comments.
a) phy-mode: lists.
b) Update axistream-connected description.
c) Moved $ref: /schemas/net/ethernet-controller.yaml# to allOf.
d) Add type to mdio.
Changes in V6:
1) Addressed below review comments.
a)add a $ref to ethernet-controller.yaml for pcs-handle.
b)Drop unused labels(axi_ethernetlite_0_mdio).
c)Not relevant to the binding(interrupt-parent).
Changes in V5:
1) Removed .txt file which was missed in V4
Changes in V4:
1)Changed the interrupts property and add allOf:if:then for it.
Changes in V3:
1) Moved RFC to PATCH.
2) Addressed below review comments
a) Indentation.
b) maxItems:3 does not match your description.
c) Filename matching compatibles.
Changes in V2:
1) remove .txt and change the name of file to xlnx,axiethernet.yaml.
2) Fix DT check warning('device_type' does not match any of the regexes:
'pinctrl-[0-9]+' From schema: Documentation/devicetree/bindings/net
/xilinx_axienet.yaml).
---
.../bindings/net/xilinx_axienet.txt | 101 ----------
.../bindings/net/xlnx,axi-ethernet.yaml | 173 ++++++++++++++++++
MAINTAINERS | 1 +
3 files changed, 174 insertions(+), 101 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/net/xilinx_axienet.txt
create mode 100644 Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml
diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt
deleted file mode 100644
index 80e505a2fda1..000000000000
--- a/Documentation/devicetree/bindings/net/xilinx_axienet.txt
+++ /dev/null
@@ -1,101 +0,0 @@
-XILINX AXI ETHERNET Device Tree Bindings
---------------------------------------------------------
-
-Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core
-provides connectivity to an external ethernet PHY supporting different
-interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two
-segments of memory for buffering TX and RX, as well as the capability of
-offloading TX/RX checksum calculation off the processor.
-
-Management configuration is done through the AXI interface, while payload is
-sent and received through means of an AXI DMA controller. This driver
-includes the DMA driver code, so this driver is incompatible with AXI DMA
-driver.
-
-For more details about mdio please refer phy.txt file in the same directory.
-
-Required properties:
-- compatible : Must be one of "xlnx,axi-ethernet-1.00.a",
- "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a"
-- reg : Address and length of the IO space, as well as the address
- and length of the AXI DMA controller IO space, unless
- axistream-connected is specified, in which case the reg
- attribute of the node referenced by it is used.
-- interrupts : Should be a list of 2 or 3 interrupts: TX DMA, RX DMA,
- and optionally Ethernet core. If axistream-connected is
- specified, the TX/RX DMA interrupts should be on that node
- instead, and only the Ethernet core interrupt is optionally
- specified here.
-- phy-handle : Should point to the external phy device if exists. Pointing
- this to the PCS/PMA PHY is deprecated and should be avoided.
- See ethernet.txt file in the same directory.
-- xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware
-
-Optional properties:
-- phy-mode : See ethernet.txt
-- xlnx,phy-type : Deprecated, do not use, but still accepted in preference
- to phy-mode.
-- xlnx,txcsum : 0 or empty for disabling TX checksum offload,
- 1 to enable partial TX checksum offload,
- 2 to enable full TX checksum offload
-- xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload
-- xlnx,switch-x-sgmii : Boolean to indicate the Ethernet core is configured to
- support both 1000BaseX and SGMII modes. If set, the phy-mode
- should be set to match the mode selected on core reset (i.e.
- by the basex_or_sgmii core input line).
-- clock-names: Tuple listing input clock names. Possible clocks:
- s_axi_lite_clk: Clock for AXI register slave interface
- axis_clk: AXI4-Stream clock for TXD RXD TXC and RXS interfaces
- ref_clk: Ethernet reference clock, used by signal delay
- primitives and transceivers
- mgt_clk: MGT reference clock (used by optional internal
- PCS/PMA PHY)
-
- Note that if s_axi_lite_clk is not specified by name, the
- first clock of any name is used for this. If that is also not
- specified, the clock rate is auto-detected from the CPU clock
- (but only on platforms where this is possible). New device
- trees should specify all applicable clocks by name - the
- fallbacks to an unnamed clock or to CPU clock are only for
- backward compatibility.
-- clocks: Phandles to input clocks matching clock-names. Refer to common
- clock bindings.
-- axistream-connected: Reference to another node which contains the resources
- for the AXI DMA controller used by this device.
- If this is specified, the DMA-related resources from that
- device (DMA registers and DMA TX/RX interrupts) rather
- than this one will be used.
- - mdio : Child node for MDIO bus. Must be defined if PHY access is
- required through the core's MDIO interface (i.e. always,
- unless the PHY is accessed through a different bus).
- Non-standard MDIO bus frequency is supported via
- "clock-frequency", see mdio.yaml.
-
- - pcs-handle: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X
- modes, where "pcs-handle" should be used to point
- to the PCS/PMA PHY, and "phy-handle" should point to an
- external PHY if exists.
-
-Example:
- axi_ethernet_eth: ethernet@40c00000 {
- compatible = "xlnx,axi-ethernet-1.00.a";
- device_type = "network";
- interrupt-parent = <µblaze_0_axi_intc>;
- interrupts = <2 0 1>;
- clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk";
- clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>;
- phy-mode = "mii";
- reg = <0x40c00000 0x40000 0x50c00000 0x40000>;
- xlnx,rxcsum = <0x2>;
- xlnx,rxmem = <0x800>;
- xlnx,txcsum = <0x2>;
- phy-handle = <&phy0>;
- axi_ethernetlite_0_mdio: mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- phy0: phy@0 {
- device_type = "ethernet-phy";
- reg = <1>;
- };
- };
- };
diff --git a/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml b/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml
new file mode 100644
index 000000000000..80843c177029
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml
@@ -0,0 +1,173 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/xlnx,axi-ethernet.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: AXI 1G/2.5G Ethernet Subsystem
+
+description: |
+ Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core
+ provides connectivity to an external ethernet PHY supporting different
+ interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two
+ segments of memory for buffering TX and RX, as well as the capability of
+ offloading TX/RX checksum calculation off the processor.
+
+ Management configuration is done through the AXI interface, while payload is
+ sent and received through means of an AXI DMA controller. This driver
+ includes the DMA driver code, so this driver is incompatible with AXI DMA
+ driver.
+
+maintainers:
+ - Radhey Shyam Pandey <radhey.shyam.pandey@xxxxxxxxxx>
+
+properties:
+ compatible:
+ enum:
+ - xlnx,axi-ethernet-1.00.a
+ - xlnx,axi-ethernet-1.01.a
+ - xlnx,axi-ethernet-2.01.a
+
+ reg:
+ description:
+ Address and length of the IO space, as well as the address
+ and length of the AXI DMA controller IO space, unless
+ axistream-connected is specified, in which case the reg
+ attribute of the node referenced by it is used.
+ maxItems: 2
+
+ interrupts:
+ items:
+ - description: Ethernet core interrupt
+ - description: Tx DMA interrupt
+ - description: Rx DMA interrupt
+ description:
+ Ethernet core interrupt is optional. If axistream-connected property is
+ present DMA node should contains TX/RX DMA interrupts else DMA interrupt
+ resources are mentioned on ethernet node.
+ minItems: 1
+
+ phy-handle: true
+
+ xlnx,rxmem:
+ description:
+ Set to allocated memory buffer for Rx/Tx in the hardware.
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ phy-mode:
+ items:
+ - description: MII
+ - description: GMII
+ - description: RGMII
+ - description: SGMII
+ - description: 1000BaseX
+ minItems: 1
+
+ xlnx,phy-type:
+ description:
+ Do not use, but still accepted in preference to phy-mode.
+ deprecated: true
+ $ref: /schemas/types.yaml#/definitions/uint32
+
+ xlnx,txcsum:
+ description:
+ TX checksum offload. 0 or empty for disabling TX checksum offload,
+ 1 to enable partial TX checksum offload and 2 to enable full TX
+ checksum offload.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
+
+ xlnx,rxcsum:
+ description:
+ RX checksum offload. 0 or empty for disabling RX checksum offload,
+ 1 to enable partial RX checksum offload and 2 to enable full RX
+ checksum offload.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2]
+
+ xlnx,switch-x-sgmii:
+ type: boolean
+ description:
+ Indicate the Ethernet core is configured to support both 1000BaseX and
+ SGMII modes. If set, the phy-mode should be set to match the mode
+ selected on core reset (i.e. by the basex_or_sgmii core input line).
+
+ clocks:
+ items:
+ - description: Clock for AXI register slave interface.
+ - description: AXI4-Stream clock for TXD RXD TXC and RXS interfaces.
+ - description: Ethernet reference clock, used by signal delay primitives
+ and transceivers.
+ - description: MGT reference clock (used by optional internal PCS/PMA PHY)
+
+ clock-names:
+ items:
+ - const: s_axi_lite_clk
+ - const: axis_clk
+ - const: ref_clk
+ - const: mgt_clk
+
+ axistream-connected:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description: Phandle of AXI DMA controller which contains the resources
+ used by this device. If this is specified, the DMA-related resources
+ from that device (DMA registers and DMA TX/RX interrupts) rather than
+ this one will be used.
+
+ mdio:
+ type: object
+
+ pcs-handle:
+ description: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X
+ modes, where "pcs-handle" should be used to point to the PCS/PMA PHY,
+ and "phy-handle" should point to an external PHY if exists.
+
+required:
+ - compatible
+ - interrupts
+ - reg
+ - xlnx,rxmem
+ - phy-handle
+
+allOf:
+ - $ref: /schemas/net/ethernet-controller.yaml#
+ - if:
+ required:
+ - axistream-connected
+
+ then:
+ properties:
+ interrupts:
+ minItems: 2
+ maxItems: 3
+
+ else:
+ properties:
+ interrupts:
+ maxItems: 1
+
+additionalProperties: false
+
+examples:
+ - |
+ axi_ethernet_eth: ethernet@40c00000 {
+ compatible = "xlnx,axi-ethernet-1.00.a";
+ interrupts = <2 0 1>;
+ clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk";
+ clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>;
+ phy-mode = "mii";
+ reg = <0x40c00000 0x40000>,<0x50c00000 0x40000>;
+ xlnx,rxcsum = <0x2>;
+ xlnx,rxmem = <0x800>;
+ xlnx,txcsum = <0x2>;
+ phy-handle = <&phy0>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@1 {
+ device_type = "ethernet-phy";
+ reg = <1>;
+ };
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 2cf9eb43ed8f..0bf527552dc9 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22895,6 +22895,7 @@ F: drivers/iio/adc/xilinx-ams.c
XILINX AXI ETHERNET DRIVER
M: Radhey Shyam Pandey <radhey.shyam.pandey@xxxxxxxxxx>
S: Maintained
+F: Documentation/devicetree/bindings/net/xlnx,axi-ethernet.yaml
F: drivers/net/ethernet/xilinx/xilinx_axienet*
XILINX CAN DRIVER
--
2.25.1
