These board files still use node name and unit address to
reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in orer to make it
easier to maintain.
Signed-off-by: Stefan Wahren <stefan.wahren@xxxxxxxx>
Cc: Marek Vasut <marex@xxxxxxx>
Cc: Wolfgang Grandegger <wg@xxxxxxxxxxxxxxxxx>
---
arch/arm/boot/dts/imx28-m28.dtsi | 44 ++-
arch/arm/boot/dts/imx28-m28cu3.dts | 354 ++++++++++++------------
arch/arm/boot/dts/imx28-m28evk.dts | 420 ++++++++++++++---------------
arch/arm/boot/dts/imx28-sps1.dts | 201 +++++++-------
4 files changed, 494 insertions(+), 525 deletions(-)
diff --git a/arch/arm/boot/dts/imx28-m28.dtsi b/arch/arm/boot/dts/imx28-m28.dtsi
index 2bdb4c093545..c08b14ad7cd5 100644
--- a/arch/arm/boot/dts/imx28-m28.dtsi
+++ b/arch/arm/boot/dts/imx28-m28.dtsi
@@ -14,31 +14,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
- apb@80000000 {
- apbh@80000000 {
- nand-controller@8000c000 {
- #address-cells = <1>;
- #size-cells = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
- status = "okay";
- };
- };
-
- apbx@80040000 {
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- rtc: rtc@68 {
- compatible = "st,m41t62";
- reg = <0x68>;
- };
- };
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -54,3 +29,22 @@ reg_3p3v: regulator@0 {
};
};
};
+
+&gpmi {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ rtc: rtc@68 {
+ compatible = "st,m41t62";
+ reg = <0x68>;
+ };
+};
diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts
index 865ac3d573c7..6b01de9efd02 100644
--- a/arch/arm/boot/dts/imx28-m28cu3.dts
+++ b/arch/arm/boot/dts/imx28-m28cu3.dts
@@ -15,187 +15,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
- apb@80000000 {
- apbh@80000000 {
- nand-controller@8000c000 {
- #address-cells = <1>;
- #size-cells = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
- status = "okay";
-
- partition@0 {
- label = "gpmi-nfc-0-boot";
- reg = <0x00000000 0x01400000>;
- read-only;
- };
-
- partition@1 {
- label = "gpmi-nfc-general-use";
- reg = <0x01400000 0x0ec00000>;
- };
- };
-
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a
- &mmc0_cd_cfg
- &mmc0_sck_cfg>;
- bus-width = <4>;
- vmmc-supply = <®_vddio_sd0>;
- status = "okay";
- };
-
- ssp2: spi@80014000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_4bit_pins_a
- &mmc2_cd_cfg
- &mmc2_sck_cfg_a>;
- bus-width = <4>;
- vmmc-supply = <®_vddio_sd1>;
- status = "okay";
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP2_SS0__GPIO_2_19
- MX28_PAD_PWM4__GPIO_3_29
- MX28_PAD_AUART2_RX__GPIO_3_8
- MX28_PAD_ENET0_RX_CLK__GPIO_4_13
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_m28: lcdif-m28@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_VSYNC__LCD_VSYNC
- MX28_PAD_LCD_HSYNC__LCD_HSYNC
- MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
- MX28_PAD_LCD_RESET__LCD_RESET
- MX28_PAD_LCD_CS__LCD_ENABLE
- MX28_PAD_AUART1_TX__GPIO_3_5
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- led_pins_gpio: leds-m28@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_SSP3_MISO__GPIO_2_26
- MX28_PAD_SSP3_SCK__GPIO_2_24
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- ocotp@8002c000 {
- status = "okay";
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_m28>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <32>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <6410256>;
- hactive = <320>;
- vactive = <240>;
- hback-porch = <38>;
- hfront-porch = <20>;
- vback-porch = <15>;
- vfront-porch = <5>;
- hsync-len = <30>;
- vsync-len = <3>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
- };
-
- apbx@80040000 {
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_b>;
- status = "okay";
- };
-
- usbphy1: usbphy@8007e000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_2pins_a>;
- status = "okay";
- };
-
- auart3: serial@80070000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart3_2pins_b>;
- status = "okay";
- };
-
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm3_pins_a>;
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb1: usb@80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins_a>;
- disable-over-current;
- status = "okay";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
- phy-reset-duration = <100>;
- status = "okay";
- };
-
- mac1: ethernet@800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- status = "okay";
- };
- };
-
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 3 5000000>;
@@ -264,3 +83,176 @@ reg_usb1_vbus: regulator@3 {
};
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_2pins_a>;
+ status = "okay";
+};
+
+&auart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart3_2pins_b>;
+ status = "okay";
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_b>;
+ status = "okay";
+};
+
+&gpmi {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+ status = "okay";
+
+ partition@0 {
+ label = "gpmi-nfc-0-boot";
+ reg = <0x00000000 0x01400000>;
+ read-only;
+ };
+
+ partition@1 {
+ label = "gpmi-nfc-general-use";
+ reg = <0x01400000 0x0ec00000>;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_m28>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <32>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <6410256>;
+ hactive = <320>;
+ vactive = <240>;
+ hback-porch = <38>;
+ hfront-porch = <20>;
+ vback-porch = <15>;
+ vfront-porch = <5>;
+ hsync-len = <30>;
+ vsync-len = <3>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <100>;
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+};
+
+&ocotp {
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SS0__GPIO_2_19
+ MX28_PAD_PWM4__GPIO_3_29
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_m28: lcdif-m28@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_VSYNC__LCD_VSYNC
+ MX28_PAD_LCD_HSYNC__LCD_HSYNC
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+ MX28_PAD_LCD_RESET__LCD_RESET
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ MX28_PAD_AUART1_TX__GPIO_3_5
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ led_pins_gpio: leds-m28@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP3_MISO__GPIO_2_26
+ MX28_PAD_SSP3_SCK__GPIO_2_24
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm3_pins_a>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a
+ &mmc0_cd_cfg
+ &mmc0_sck_cfg>;
+ bus-width = <4>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+};
+
+&ssp2 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_4bit_pins_a
+ &mmc2_cd_cfg
+ &mmc2_sck_cfg_a>;
+ bus-width = <4>;
+ vmmc-supply = <®_vddio_sd1>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_pins_a>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
index 13acdc7916b9..e350d57a4cec 100644
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ b/arch/arm/boot/dts/imx28-m28evk.dts
@@ -11,220 +11,6 @@ / {
model = "Aries/DENX M28EVK";
compatible = "aries,m28evk", "denx,m28evk", "fsl,imx28";
- apb@80000000 {
- apbh@80000000 {
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_8bit_pins_a
- &mmc0_cd_cfg
- &mmc0_sck_cfg>;
- bus-width = <8>;
- wp-gpios = <&gpio3 10 0>;
- vmmc-supply = <®_vddio_sd0>;
- status = "okay";
- };
-
- ssp2: spi@80014000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-
- flash: flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "m25p80", "jedec,spi-nor";
- spi-max-frequency = <40000000>;
- reg = <0>;
- };
- };
-
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_PWM3__GPIO_3_28
- MX28_PAD_AUART2_CTS__GPIO_3_10
- MX28_PAD_AUART2_RTS__GPIO_3_11
- MX28_PAD_AUART3_RX__GPIO_3_12
- MX28_PAD_AUART3_TX__GPIO_3_13
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- lcdif_pins_m28: lcdif-m28@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
- MX28_PAD_LCD_ENABLE__LCD_ENABLE
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
- };
-
- lcdif@80030000 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcdif_24bit_pins_a
- &lcdif_pins_m28>;
- display = <&display0>;
- status = "okay";
-
- display0: display0 {
- bits-per-pixel = <16>;
- bus-width = <18>;
-
- display-timings {
- native-mode = <&timing0>;
- timing0: timing0 {
- clock-frequency = <33260000>;
- hactive = <800>;
- vactive = <480>;
- hback-porch = <0>;
- hfront-porch = <256>;
- vback-porch = <0>;
- vfront-porch = <45>;
- hsync-len = <1>;
- vsync-len = <1>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <1>;
- };
- };
- };
- };
-
- can0: can@80032000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can0_pins_a>;
- status = "okay";
- };
-
- can1: can@80034000 {
- pinctrl-names = "default";
- pinctrl-0 = <&can1_pins_a>;
- status = "okay";
- };
- };
-
- apbx@80040000 {
- saif0: saif@80042000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif0_pins_a>;
- status = "okay";
- };
-
- saif1: saif@80046000 {
- pinctrl-names = "default";
- pinctrl-0 = <&saif1_pins_a>;
- fsl,saif-master = <&saif0>;
- status = "okay";
- };
-
- i2c0: i2c@80058000 {
- sgtl5000: codec@a {
- compatible = "fsl,sgtl5000";
- reg = <0x0a>;
- #sound-dai-cells = <0>;
- VDDA-supply = <®_3p3v>;
- VDDIO-supply = <®_3p3v>;
- clocks = <&saif0>;
- };
-
- eeprom: eeprom@51 {
- compatible = "atmel,24c128";
- reg = <0x51>;
- pagesize = <32>;
- };
- };
-
- lradc@80050000 {
- status = "okay";
- fsl,lradc-touchscreen-wires = <4>;
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
-
- usbphy1: usbphy@8007e000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- status = "okay";
- };
-
- auart1: serial@8006c000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart1_pins_a>;
- status = "okay";
- };
-
- auart2: serial@8006e000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart2_2pins_b>;
- status = "okay";
- };
-
- pwm: pwm@80064000 {
- pinctrl-names = "default";
- pinctrl-0 = <&pwm4_pins_a>;
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- vbus-supply = <®_usb0_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_pins_a>;
- status = "okay";
- };
-
- usb1: usb@80090000 {
- vbus-supply = <®_usb1_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins_a>;
- status = "okay";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- clocks = <&clks 57>, <&clks 57>;
- clock-names = "ipg", "ahb";
- status = "okay";
- };
-
- mac1: ethernet@800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- status = "okay";
- };
- };
-
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 4 5000000>;
@@ -269,3 +55,209 @@ sound {
audio-codec = <&sgtl5000>;
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ status = "okay";
+};
+
+&auart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart1_pins_a>;
+ status = "okay";
+};
+
+&auart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart2_2pins_b>;
+ status = "okay";
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&i2c0 {
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <®_3p3v>;
+ VDDIO-supply = <®_3p3v>;
+ clocks = <&saif0>;
+ };
+
+ eeprom: eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcdif_24bit_pins_a
+ &lcdif_pins_m28>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display0 {
+ bits-per-pixel = <16>;
+ bus-width = <18>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33260000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <0>;
+ hfront-porch = <256>;
+ vback-porch = <0>;
+ vfront-porch = <45>;
+ hsync-len = <1>;
+ vsync-len = <1>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+ };
+ };
+};
+
+&lradc {
+ status = "okay";
+ fsl,lradc-touchscreen-wires = <4>;
+};
+
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can0_pins_a>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins_a>;
+ status = "okay";
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ clocks = <&clks 57>, <&clks 57>;
+ clock-names = "ipg", "ahb";
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_AUART2_CTS__GPIO_3_10
+ MX28_PAD_AUART2_RTS__GPIO_3_11
+ MX28_PAD_AUART3_RX__GPIO_3_12
+ MX28_PAD_AUART3_TX__GPIO_3_13
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ lcdif_pins_m28: lcdif-m28@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+ MX28_PAD_LCD_ENABLE__LCD_ENABLE
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm4_pins_a>;
+ status = "okay";
+};
+
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ status = "okay";
+};
+
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a
+ &mmc0_cd_cfg
+ &mmc0_sck_cfg>;
+ bus-width = <8>;
+ wp-gpios = <&gpio3 10 0>;
+ vmmc-supply = <®_vddio_sd0>;
+ status = "okay";
+};
+
+&ssp2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ flash: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80", "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+ };
+};
+
+&usb0 {
+ vbus-supply = <®_usb0_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_pins_a>;
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_pins_a>;
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
index 90928db0df70..5d74a68c56ff 100644
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ b/arch/arm/boot/dts/imx28-sps1.dts
@@ -15,111 +15,6 @@ memory@40000000 {
reg = <0x40000000 0x08000000>;
};
- apb@80000000 {
- apbh@80000000 {
- pinctrl@80018000 {
- pinctrl-names = "default";
- pinctrl-0 = <&hog_pins_a>;
-
- hog_pins_a: hog-gpios@0 {
- reg = <0>;
- fsl,pinmux-ids = <
- MX28_PAD_GPMI_D00__GPIO_0_0
- MX28_PAD_GPMI_D03__GPIO_0_3
- MX28_PAD_GPMI_D06__GPIO_0_6
- >;
- fsl,drive-strength = <MXS_DRIVE_4mA>;
- fsl,voltage = <MXS_VOLTAGE_HIGH>;
- fsl,pull-up = <MXS_PULL_DISABLE>;
- };
-
- };
-
- ssp0: spi@80010000 {
- compatible = "fsl,imx28-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_4bit_pins_a>;
- bus-width = <4>;
- status = "okay";
- };
-
- ssp2: spi@80014000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx28-spi";
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-
- flash: flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "everspin,mr25h256", "mr25h256";
- spi-max-frequency = <40000000>;
- reg = <0>;
- };
- };
- };
-
- apbx@80040000 {
- i2c0: i2c@80058000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- rtc: rtc@51 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
-
- eeprom: eeprom@52 {
- compatible = "atmel,24c64";
- reg = <0x52>;
- pagesize = <32>;
- };
- };
-
- duart: serial@80074000 {
- pinctrl-names = "default";
- pinctrl-0 = <&duart_pins_a>;
- status = "okay";
- };
-
- usbphy0: usbphy@8007c000 {
- status = "okay";
- };
-
- auart0: serial@8006a000 {
- pinctrl-names = "default";
- pinctrl-0 = <&auart0_pins_a>;
- status = "okay";
- };
- };
- };
-
- ahb@80080000 {
- usb0: usb@80080000 {
- vbus-supply = <®_usb0_vbus>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb0_pins_b>;
- status = "okay";
- };
-
- mac0: ethernet@800f0000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac0_pins_a>;
- status = "okay";
- };
-
- mac1: ethernet@800f4000 {
- phy-mode = "rmii";
- pinctrl-names = "default";
- pinctrl-0 = <&mac1_pins_a>;
- status = "okay";
- };
- };
-
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -164,3 +59,99 @@ led@3 {
};
};
+
+&auart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&auart0_pins_a>;
+ status = "okay";
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ rtc: rtc@51 {
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ eeprom: eeprom@52 {
+ compatible = "atmel,24c64";
+ reg = <0x52>;
+ pagesize = <32>;
+ };
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ status = "okay";
+};
+
+&mac1 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac1_pins_a>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a>;
+
+ hog_pins_a: hog-gpios@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D00__GPIO_0_0
+ MX28_PAD_GPMI_D03__GPIO_0_3
+ MX28_PAD_GPMI_D06__GPIO_0_6
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_4bit_pins_a>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ssp2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+
+ flash: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "everspin,mr25h256", "mr25h256";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+ };
+};
+
+&usb0 {
+ vbus-supply = <®_usb0_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_pins_b>;
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
--
2.34.1
