On Wed, 18 Jan 2023 at 07:19, Yanhong Wang
<yanhong.wang@xxxxxxxxxxxxxxxx> wrote:
> Add JH7110 ethernet device node to support gmac driver for the JH7110
> RISC-V SoC.
>
> Signed-off-by: Yanhong Wang <yanhong.wang@xxxxxxxxxxxxxxxx>
> ---
> arch/riscv/boot/dts/starfive/jh7110.dtsi | 93 ++++++++++++++++++++++++
> 1 file changed, 93 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index c22e8f1d2640..c6de6e3b1a25 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -433,5 +433,98 @@
> reg-shift = <2>;
> status = "disabled";
> };
> +
> + stmmac_axi_setup: stmmac-axi-config {
> + snps,lpi_en;
> + snps,wr_osr_lmt = <4>;
> + snps,rd_osr_lmt = <4>;
> + snps,blen = <256 128 64 32 0 0 0>;
> + };
> +
> + gmac0: ethernet@16030000 {
> + compatible = "starfive,jh7110-dwmac", "snps,dwmac-5.20";
> + reg = <0x0 0x16030000 0x0 0x10000>;
> + clocks = <&aoncrg JH7110_AONCLK_GMAC0_AXI>,
> + <&aoncrg JH7110_AONCLK_GMAC0_AHB>,
> + <&syscrg JH7110_SYSCLK_GMAC0_PTP>,
> + <&aoncrg JH7110_AONCLK_GMAC0_TX>,
The gmac0_tx clock is a mux that takes either the gmac0_gtxclk or
rmii_rtx as parent. However it is then followed by an inverter that
optionally inverts the clock, gmac0_tx_inv. I'm guessing this
optionally inverted signal is what is actually used (otherwise why
would the inverter exist), so I think this clock is what should be
claimed here. Eg.
<&aoncrg JH7110_AONCLK_GMAC0_TX_INV>,
Right now it works only because the inverted signal can't be gated
(turned off) even when it's not claimed by any driver.
> + <&syscrg JH7110_SYSCLK_GMAC0_GTXC>,
> + <&syscrg JH7110_SYSCLK_GMAC0_GTXCLK>;
Here the gmac0_gtxclk clock is the parent of the gmac0_gtxc, so
claiming the gmac0_gtxc should be enough. Since the gmac0_gtxc is just
a gate it should have the CLK_SET_RATE_PARENT flag set, so the driver
can just change the rate of the child and it should propagate to the
parent. In short I think claiming only the gmac0_gtxc clock should be
enough here.
> + clock-names = "stmmaceth", "pclk", "ptp_ref",
> + "tx", "gtxc", "gtx";
> + resets = <&aoncrg JH7110_AONRST_GMAC0_AXI>,
> + <&aoncrg JH7110_AONRST_GMAC0_AHB>;
> + reset-names = "stmmaceth", "ahb";
> + interrupts = <7>, <6>, <5>;
> + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
> + phy-mode = "rgmii-id";
> + snps,multicast-filter-bins = <64>;
> + snps,perfect-filter-entries = <8>;
> + rx-fifo-depth = <2048>;
> + tx-fifo-depth = <2048>;
> + snps,fixed-burst;
> + snps,no-pbl-x8;
> + snps,force_thresh_dma_mode;
> + snps,axi-config = <&stmmac_axi_setup>;
> + snps,tso;
> + snps,en-tx-lpi-clockgating;
> + snps,txpbl = <16>;
> + snps,rxpbl = <16>;
> + status = "disabled";
> + phy-handle = <&phy0>;
> +
> + mdio0: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> +
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> + };
> + };
> + };
> +
> + gmac1: ethernet@16040000 {
> + compatible = "starfive,jh7110-dwmac", "snps,dwmac-5.20";
> + reg = <0x0 0x16040000 0x0 0x10000>;
> + clocks = <&syscrg JH7110_SYSCLK_GMAC1_AXI>,
> + <&syscrg JH7110_SYSCLK_GMAC1_AHB>,
> + <&syscrg JH7110_SYSCLK_GMAC1_PTP>,
> + <&syscrg JH7110_SYSCLK_GMAC1_TX>,
> + <&syscrg JH7110_SYSCLK_GMAC1_GTXC>,
> + <&syscrg JH7110_SYSCLK_GMAC1_GTXCLK>;
> + clock-names = "stmmaceth", "pclk", "ptp_ref",
> + "tx", "gtxc", "gtx";
> + resets = <&syscrg JH7110_SYSRST_GMAC1_AXI>,
> + <&syscrg JH7110_SYSRST_GMAC1_AHB>;
> + reset-names = "stmmaceth", "ahb";
> + interrupts = <78>, <77>, <76>;
> + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
> + phy-mode = "rgmii-id";
> + snps,multicast-filter-bins = <64>;
> + snps,perfect-filter-entries = <8>;
> + rx-fifo-depth = <2048>;
> + tx-fifo-depth = <2048>;
> + snps,fixed-burst;
> + snps,no-pbl-x8;
> + snps,force_thresh_dma_mode;
> + snps,axi-config = <&stmmac_axi_setup>;
> + snps,tso;
> + snps,en-tx-lpi-clockgating;
> + snps,txpbl = <16>;
> + snps,rxpbl = <16>;
> + status = "disabled";
> + phy-handle = <&phy1>;
> +
> + mdio1: mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> +
> + phy1: ethernet-phy@1 {
> + reg = <1>;
> + };
> + };
> + };
> };
> };
> --
> 2.17.1
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-riscv
