Re: [PATCH v9 0/8] i2c-atr and FPDLink

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On 16/02/2023 17:53, Andy Shevchenko wrote:
On Thu, Feb 16, 2023 at 04:07:39PM +0200, Tomi Valkeinen wrote:

...

+	if (!c2a)

I would expect here dev_warn() to let user know about "shouldn't happened, but
have happened" situation.

Sure, I'll add.

+		return; /* This shouldn't happen */

...

-	static const struct v4l2_mbus_framefmt format = {
+	static const struct v4l2_mbus_framefmt informat = {

Naming a bit confusing. Is it "information" that cut or what?

in_format

Indeed, that's better.

+	static const struct v4l2_mbus_framefmt outformat = {

out_format

...

-out_unlock:
+out:

Why?

I think this was a mistake, I'll change it back.

...

+/*
+ * (Possible) TODOs

TODOs:

Ok...

+ *
+ * - PM for serializer and remote peripherals. We need to manage:
+ *   - VPOC
+ *     - Power domain? Regulator? Somehow any remote device should be able to
+ *       cause the VPOC to be turned on.
+ *   - Link between the deserializer and the serializer
+ *     - Related to VPOC management. We probably always want to turn on the VPOC
+ *       and then enable the link.
+ *   - Serializer's services: i2c, gpios, power
+ *     - The serializer needs to resume before the remote peripherals can
+ *       e.g. use the i2c.
+ *     - How to handle gpios? Reserving a gpio essentially keeps the provider
+ *       (serializer) always powered on.
+ * - Do we need a new bus for the FPD-Link? At the moment the serializers
+ *   are children of the same i2c-adapter where the deserializer resides.
+ * - i2c-atr could be made embeddable instead of allocatable.
+ */

...

  struct atr_alias_table_entry {
  	u16 alias_id;	/* Alias ID from DT */
- bool reserved;
+	bool in_use;
  	u8 nport;
  	u8 slave_id;	/* i2c client's local i2c address */
  	u8 port_reg_idx;

Wouldn't be wiser to move boolean at the end so if any obscure
architecture/compiler makes it longer than a byte it won't increase the memory
footprint. (Actually wouldn't it be aligned to u16 followed by u8 as well as
they are different types?)

Sure, I can move it.

  };

...

+static int ub960_read16(struct ub960_data *priv, u8 reg, u16 *val)
+{
+	struct device *dev = &priv->client->dev;
+	unsigned int v1, v2;
+	int ret;
+
+	mutex_lock(&priv->reg_lock);
+
+	ret = regmap_read(priv->regmap, reg, &v1);
+	if (ret) {
+		dev_err(dev, "%s: cannot read register 0x%02x (%d)!\n",
+			__func__, reg, ret);
+		goto out_unlock;
+	}
+
+	ret = regmap_read(priv->regmap, reg + 1, &v2);
+	if (ret) {
+		dev_err(dev, "%s: cannot read register 0x%02x (%d)!\n",
+			__func__, reg + 1, ret);
+		goto out_unlock;
+	}

Wondering why bulk read can't be used against properly typed __be16 variable?

I'll do that.

+	*val = (v1 << 8) | v2;

+ be16_to_cpu() here.

Yep.

+out_unlock:
+	mutex_unlock(&priv->reg_lock);
+
+	return ret;
+}

...

+static int ub960_rxport_read16(struct ub960_data *priv, u8 nport, u8 reg,
+			       u16 *val)
  {

Ditto.

+}

...

  	struct i2c_board_info ser_info = {
-		.of_node = to_of_node(rxport->remote_fwnode),
-		.fwnode = rxport->remote_fwnode,

+		.of_node = to_of_node(rxport->ser.fwnode),
+		.fwnode = rxport->ser.fwnode,

Why do you need to have both?!

I didn't debug it, but having only fwnode there will break the probing (no match).

  		.platform_data = ser_pdata,
  	};

...

+	for (nport = 0; nport < priv->hw_data->num_rxports; ++nport) {

Pre-increment is non-standard in the kernel.

+		struct ub960_rxport *rxport = priv->rxports[nport];
+		struct v4l2_mbus_frame_desc desc;
+		int ret;
+		u8 cur_vc;
+
+		if (!rxport)
+			continue;
+
+		ret = v4l2_subdev_call(rxport->source.sd, pad, get_frame_desc,
+				       rxport->source.pad, &desc);
+		if (ret)
+			return ret;
+
+		if (desc.type != V4L2_MBUS_FRAME_DESC_TYPE_CSI2)
+			continue;

		cur_vc = desc.entry[0].bus.csi2.vc;

+		for (i = 0; i < desc.num_entries; ++i) {
+			u8 vc = desc.entry[i].bus.csi2.vc;

+			if (i == 0) {
+				cur_vc = vc;
+				continue;
+			}

This is an invariant to the loop, see above.

Well, the current code handles the case of num_entries == 0. I can change it as you suggest, and first check if num_entries == 0 and also start the loop from 1.

+			if (vc == cur_vc)
+				continue;
+
+			dev_err(&priv->client->dev,
+				"rx%u: source with multiple virtual-channels is not supported\n",
+				nport);
+			return -ENODEV;
+		}
+	}

...

+	for (i = 0; i < 6; ++i)
  		ub960_read(priv, UB960_SR_FPD3_RX_ID(i), &id[i]);
  	id[6] = 0;

Wondering if this magic can be defined.

The number of ID registers? Yes, I can add a define.

...

+	priv->atr.aliases = devm_kcalloc(dev, table_size,
+					 sizeof(struct atr_alias_table_entry),

	sizeof(*priv->atr.aliases) ?

Sure.

+					 GFP_KERNEL);
+	if (!priv->atr.aliases)
  		return -ENOMEM;

...

  	if (ret) {
  		if (ret != -EINVAL) {
-			dev_err(dev,
-				"rx%u: failed to read 'ti,strobe-pos': %d\n",
-				nport, ret);
+			dev_err(dev, "rx%u: failed to read '%s': %d\n", nport,
+				"ti,strobe-pos", ret);
  			return ret;
  		}
  	} else if (strobe_pos < UB960_MIN_MANUAL_STROBE_POS ||
@@ -3512,8 +3403,8 @@ ub960_parse_dt_rxport_link_properties(struct ub960_data *priv,
  	ret = fwnode_property_read_u32(link_fwnode, "ti,eq-level", &eq_level);
  	if (ret) {
  		if (ret != -EINVAL) {
-			dev_err(dev, "rx%u: failed to read 'ti,eq-level': %d\n",
-				nport, ret);
+			dev_err(dev, "rx%u: failed to read '%s': %d\n", nport,
+				"ti,eq-level", ret);
  			return ret;
  		}
  	} else if (eq_level > UB960_MAX_EQ_LEVEL) {


Hmm, I noticed this one (and the one above) was missing return -EINVAL.

Seems like you may do (in both cases) similar to the above:

	var = 0;
	ret = read_u32();
	if (ret && ret != -EINVAL) {
		// error handling
	}
	if (var > limit) {
		// another error handling
	}

That's not the same. You'd also need to do:

if (!ret) {
	// handle the retrieved value
}

which, I think, is not any clearer (perhaps more unclear).

What I could do is:

if (ret) {
	if (ret != -EINVAL) {
		dev_err(dev, "rx%u: failed to read '%s': %d\n", nport,
			"ti,eq-level", ret);
		return ret;
	}
} else {
	if (eq_level > UB960_MAX_EQ_LEVEL) {
		dev_err(dev, "rx%u: illegal 'ti,eq-level' value: %d\n",
			nport, eq_level);
		return -EINVAL;
	}

	rxport->eq.manual_eq = true;
	rxport->eq.manual.eq_level = eq_level;
}

Maybe the above style makes it clearer, as it clearly splits the "don't have value" and "have value" branches.

...

+	static const char *vpoc_names[UB960_MAX_RX_NPORTS] = { "vpoc0", "vpoc1",
+							       "vpoc2", "vpoc3" };

Wouldn't be better to format it as

	static const char *vpoc_names[UB960_MAX_RX_NPORTS] = {
		"vpoc0", "vpoc1", "vpoc2", "vpoc3",
	};

?

Clang-format disagrees, but I agree with you ;).

 Tomi




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux