On Mon, Feb 13, 2023 at 11:56:52AM +0000, Andre Przywara wrote: > On Mon, 13 Feb 2023 10:18:03 +0100 > Maxime Ripard <maxime@xxxxxxxxxx> wrote: > > On Mon, Feb 13, 2023 at 09:49:55AM +0100, pelzi@xxxxxxxxxxxxxxx wrote: > > > Am 13.02.23 um 09:43 schrieb Maxime Ripard: > > > > On Fri, Feb 10, 2023 at 10:18:14AM +0000, Andre Przywara wrote: > > > > > > > Not sure if you were actually arguing this, but the change I sketched > > > > > > > above (interpreting 0 as 24MHz/1) is separate though, as the current > > > > > > > default is "no DT property", and not 0. There is no input-debounce > > > > > > > property user in the kernel tree at the moment, so we wouldn't break > > > > > > > anyone. The only thing that would change is if a downstream user was > > > > > > > relying on "0" being interpreted as "skip the setup", which isn't > > > > > > > really documented and could be argued to be an implementation detail. > > > > > > > > > > > > > > So I'd suggest to implement 0 as "lowest possible", and documenting that > > > > > > > and the 32KHz/1 default if no property is given. > > > > > > Ah, my bad. > > > > > > > > > > > > There's another thing to consider: there's already a generic per-pin > > > > > > input-debounce property in pinctrl. > > > > > > > > > > > > Since we can't control it per pin but per bank, we moved it to the > > > > > > controller back then, but there's always been this (implicit) > > > > > > expectation that it was behaving the same way. > > > > > > > > > > > > And the generic, per-pin, input-debounce documentation says: > > > > > > > > > > > > > Takes the debounce time in usec as argument or 0 to disable debouncing > > > > > > I agree that silently ignoring it is not great, but interpreting 0 as > > > > > > the lowest possible is breaking that behaviour which, I believe, is a > > > > > > worse outcome. > > > > > Is it really? If I understand the hardware manuals correctly, we cannot > > > > > really turn that feature off, so isn't the lowest possible time period (24 > > > > > MHz/1 at the moment) the closest we can get to "turn it off"? So > > > > > implementing this would bring us actually closer to the documented > > > > > behaviour? Or did I get the meaning of this time period wrong? > > > > > At least that's my understanding of how it fixed Andreas' problem: 1µs > > > > > is still not "off", but much better than the 31µs of the default. The new > > > > > 0 would then be 0.041µs. > > > > My point was that the property we share the name (and should share the > > > > semantics with) documents 0 as disabled. We would have a behavior that > > > > doesn't disable it. It's inconsistent. > > > > > > > > The reason doesn't really matter, we would share the same name but have > > > > a completely different behavior, this is super confusing to me. > > > > > > I got the point. As far as I can tell from the datasheet, it is not possible > > > to actually switch off input-debounce. But as a debounce filter is actually > > > a low-pass filter, setting the cut-off frequency as high as possible, > > > appears to be the equivalent to switching it off. > > > > It's not really a matter of hardware here, it's a matter of driver > > behavior vs generic behavior from the framework. The hardware obviously > > influences the former, but it's marginal in that discussion. > > > > As that whole discussion shows, whether the frequency would be high > > enough is application dependent, and thus we cannot just claim that it's > > equivalent in all circumstances. > > > > Making such an assumption will just bite someone else down the road, > > except this time we will have users (you, I'd assume) relying on that > > behavior so we wouldn't be able to address it. > > > > But I also agree with the fact that doing nothing with 0 is bad UX and > > confusing as well. > > > > I still think that we can address both by just erroring out on 0 / > > printing an error message so that it's obvious that we can't support it, > > and we wouldn't change the semantics of the property either. > > > > And then you can set the actual debouncing time you need instead of > > "whatever" in the device tree. > > I am on the same page with regards to discouraging 0 as a proper value, and > that we should warn if this is being used. Great :) > However I think we should at the same time try to still get as low as > possible when 0 is specified. It's still undefined behaviour though. It will be context dependent, and if we ever encounter a bug at 1/24MHz, we'll change that value to something else that might break other users that were relying on that value. > The debounce property uses microseconds as the unit, but even the AW > hardware allows us to go lower than this. So we would leave that on > the table, somewhat needlessly: input-debounce = <1> would give us > 1333 ns, when the lowest possible is about 42 ns (1/24MHz). > > So what about the following: > We document that 0 does not mean off, but tries to get as low as possible. I still don't really like the fact that we're changing the semantics of that property. > If the driver sees 0, it issues a warning, but still tries to lower the > debounce period as much as possible, and reports that, like: > [1.2345678] 1c20800.pinctrl: cannot turn off debouncing, setting to 41.7 ns I just thought about another thing that might be a solution: instead of checking/enforcing the input-debounce value at probe time, we can do so when the pin is configured. That way, the pinctrl driver will load without affecting the system boot too much, but we would still reject pin configurations whose bank are using 0. Actually configuring the debounce per bank each time is configured is probably going to complexify the driver, so we could set it up in the probe, and default to the lowest debouncing value if it's zero, but we would still actively check for that value to not be 0 as soon as a pin is configured which would effectively prevent anyone from using that value. I think this would be a good compromise? > Alternatively we use a different property name, if that is a concern. We > could then use nanoseconds as a unit value, and then can error out on 0. I mean, if that's a concern, we can also introduce an input-debounce-ns property that is mutually exclusive with input-debounce, with both erroring out on 0. Maxime
