On 2/14/2023 9:27 PM, Bartosz Golaszewski wrote:
From: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> Add the serial port connected to the GNSS on sa8775p-ride.
Same here, this is for BT HS UART. -Shazad
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@xxxxxxxxxx> --- arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 34 +++++++++++++++++++++++ arch/arm64/boot/dts/qcom/sa8775p.dtsi | 17 ++++++++++++ 2 files changed, 51 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts index d01ca3a9ee37..9aee6e4c1ba1 100644 --- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts +++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dts @@ -13,6 +13,7 @@ / {aliases {serial0 = &uart10; + serial1 = &uart17; i2c18 = &i2c18; spi16 = &spi16; }; @@ -66,6 +67,30 @@ qup_i2c18_default: qup-i2c18-state { drive-strength = <2>; bias-pull-up; }; + + qup_uart17_cts: qup-uart17-cts-state { + pins = "gpio91"; + function = "qup2_se3"; + bias-disable; + }; + + qup_uart17_rts: qup0_uart17_rts-state { + pins = "gpio92"; + function = "qup2_se3"; + bias-pull-down; + }; + + qup_uart17_tx: qup0_uart17_tx-state { + pins = "gpio93"; + function = "qup2_se3"; + bias-pull-up; + }; + + qup_uart17_rx: qup0_uart17_rx-state { + pins = "gpio94"; + function = "qup2_se3"; + bias-pull-down; + }; };&uart10 {@@ -75,6 +100,15 @@ &uart10 { status = "okay"; };+&uart17 {+ pinctrl-0 = <&qup_uart17_cts>, + <&qup_uart17_rts>, + <&qup_uart17_tx>, + <&qup_uart17_rx>; + pinctrl-names = "default"; + status = "okay"; +}; + &xo_board_clk { clock-frequency = <38400000>; }; diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi index 1abb545ff4f4..b009e1100c0a 100644 --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi @@ -524,6 +524,23 @@ &config_noc SLAVE_QUP_2 0>, status = "disabled"; };+ uart17: serial@88c000 {+ compatible = "qcom,geni-uart"; + reg = <0x0 0x88c000 0x0 0x4000>; + interrupts-extended = <&intc GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>, + <&tlmm 94 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>; + clock-names = "se"; + interconnects = <&clk_virt MASTER_QUP_CORE_2 0 + &clk_virt SLAVE_QUP_CORE_2 0>, + <&gem_noc MASTER_APPSS_PROC 0 + &config_noc SLAVE_QUP_2 0>; + interconnect-names = "qup-core", + "qup-config"; + power-domains = <&rpmhpd SA8775P_CX>; + status = "disabled"; + }; + i2c18: i2c@890000 { compatible = "qcom,geni-i2c"; reg = <0x0 0x890000 0x0 0x4000>;
