On 10/02/2023 16:44, Neil Armstrong wrote:
Add the Display Port controller subnode to the MDSS node.
Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sm8450.dtsi | 79 ++++++++++++++++++++++++++++++++++++
1 file changed, 79 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 6caa2c8efb46..72d54beb7d7c 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2751,6 +2751,13 @@ dpu_intf2_out: endpoint {
};
};
+ port@2 {
+ reg = <2>;
+ dpu_intf0_out: endpoint {
+ remote-endpoint = <&mdss_dp0_in>;
+ };
+ };
+
};
mdp_opp_table: opp-table {
@@ -2783,6 +2790,78 @@ opp-500000000 {
};
};
+ mdss_dp0: displayport-controller@ae90000 {
+ compatible = "qcom,sm8350-dp";
Missing "qcom,sm8450-dp". As I wrote in the comment to patch 1, I'd
suggest having just a single entry here rather than keeping both 8350
and 8450 entries.
+ reg = <0 0xae90000 0 0xfc>,
+ <0 0xae90200 0 0xc0>,
+ <0 0xae90400 0 0x770>,
+ <0 0xae91000 0 0x98>,
+ <0 0xae91400 0 0x98>;
While this sounds correct, usually we used the even size here (0x200,
0x400, etc.). Can we please switch to it (especially since sm8350-dp
uses even sizes).
+ interrupt-parent = <&mdss>;
+ interrupts = <12>;
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX0_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK>;
+ clock-names = "core_iface",
+ "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface",
+ "stream_pixel";
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
+ <&dispcc DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&usb_1_qmpphy QMP_USB43DP_DP_LINK_CLK>,
+ <&usb_1_qmpphy QMP_USB43DP_DP_VCO_DIV_CLK>;
+
+ phys = <&usb_1_qmpphy QMP_USB43DP_DP_PHY>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ operating-points-v2 = <&dp_opp_table>;
+ power-domains = <&rpmhpd SM8450_MMCX>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss_dp0_in: endpoint {
+ remote-endpoint = <&dpu_intf0_out>;
+ };
+ };
+ };
+
+ dp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
mdss_dsi0: dsi@ae94000 {
compatible = "qcom,sm8450-dsi-ctrl", "qcom,mdss-dsi-ctrl";
reg = <0 0x0ae94000 0 0x400>;
--
With best wishes
Dmitry
