The default bias pull up value for the tlmm i2c data clk states is 2.2kOhms. Add this value to make sure the driver factors in the i2c pull up bit when writing the config register. Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxx> --- The v3 of this specific patch is here: https://lore.kernel.org/all/20230208081836.984673-2-abel.vesa@xxxxxxxxxx/ Changes since v3: * none arch/arm64/boot/dts/qcom/sm8550.dtsi | 30 ++++++++++++++-------------- 1 file changed, 15 insertions(+), 15 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi index 1dea055a6815..6e60afc748cf 100644 --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi @@ -2695,7 +2695,7 @@ qup_i2c0_data_clk: qup-i2c0-data-clk-state { pins = "gpio28", "gpio29"; function = "qup1_se0"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c1_data_clk: qup-i2c1-data-clk-state { @@ -2703,7 +2703,7 @@ qup_i2c1_data_clk: qup-i2c1-data-clk-state { pins = "gpio32", "gpio33"; function = "qup1_se1"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c2_data_clk: qup-i2c2-data-clk-state { @@ -2711,7 +2711,7 @@ qup_i2c2_data_clk: qup-i2c2-data-clk-state { pins = "gpio36", "gpio37"; function = "qup1_se2"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c3_data_clk: qup-i2c3-data-clk-state { @@ -2719,7 +2719,7 @@ qup_i2c3_data_clk: qup-i2c3-data-clk-state { pins = "gpio40", "gpio41"; function = "qup1_se3"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c4_data_clk: qup-i2c4-data-clk-state { @@ -2727,7 +2727,7 @@ qup_i2c4_data_clk: qup-i2c4-data-clk-state { pins = "gpio44", "gpio45"; function = "qup1_se4"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c5_data_clk: qup-i2c5-data-clk-state { @@ -2735,7 +2735,7 @@ qup_i2c5_data_clk: qup-i2c5-data-clk-state { pins = "gpio52", "gpio53"; function = "qup1_se5"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c6_data_clk: qup-i2c6-data-clk-state { @@ -2743,7 +2743,7 @@ qup_i2c6_data_clk: qup-i2c6-data-clk-state { pins = "gpio48", "gpio49"; function = "qup1_se6"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c8_data_clk: qup-i2c8-data-clk-state { @@ -2751,14 +2751,14 @@ scl-pins { pins = "gpio57"; function = "qup2_se0_l1_mira"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; sda-pins { pins = "gpio56"; function = "qup2_se0_l0_mira"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; }; @@ -2767,7 +2767,7 @@ qup_i2c9_data_clk: qup-i2c9-data-clk-state { pins = "gpio60", "gpio61"; function = "qup2_se1"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c10_data_clk: qup-i2c10-data-clk-state { @@ -2775,7 +2775,7 @@ qup_i2c10_data_clk: qup-i2c10-data-clk-state { pins = "gpio64", "gpio65"; function = "qup2_se2"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c11_data_clk: qup-i2c11-data-clk-state { @@ -2783,7 +2783,7 @@ qup_i2c11_data_clk: qup-i2c11-data-clk-state { pins = "gpio68", "gpio69"; function = "qup2_se3"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c12_data_clk: qup-i2c12-data-clk-state { @@ -2791,7 +2791,7 @@ qup_i2c12_data_clk: qup-i2c12-data-clk-state { pins = "gpio2", "gpio3"; function = "qup2_se4"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c13_data_clk: qup-i2c13-data-clk-state { @@ -2799,7 +2799,7 @@ qup_i2c13_data_clk: qup-i2c13-data-clk-state { pins = "gpio80", "gpio81"; function = "qup2_se5"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_i2c15_data_clk: qup-i2c15-data-clk-state { @@ -2807,7 +2807,7 @@ qup_i2c15_data_clk: qup-i2c15-data-clk-state { pins = "gpio72", "gpio106"; function = "qup2_se7"; drive-strength = <2>; - bias-pull-up; + bias-pull-up = <2200>; }; qup_spi0_cs: qup-spi0-cs-state { -- 2.34.1
