Hi, On Wed, Nov 12, 2014 at 04:41:33PM -0600, George McCollister wrote: > diff --git a/arch/arm/boot/dts/am335x-lxm.dts b/arch/arm/boot/dts/am335x-lxm.dts > new file mode 100644 > index 0000000..0f7cbae > --- /dev/null > +++ b/arch/arm/boot/dts/am335x-lxm.dts > @@ -0,0 +1,354 @@ > +/* > + * Copyright (C) 2014 NovaTech LLC - http://www.novatechweb.com > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > +/dts-v1/; > + > +#include "am33xx.dtsi" > + > +/ { > + model = "NovaTech OrionLXm"; > + compatible = "novatech,am335x-lxm", "ti,am33xx"; > + > + cpus { > + cpu@0 { > + cpu0-supply = <&vdd1_reg>; > + }; > + }; > + > + memory { > + device_type = "memory"; > + reg = <0x80000000 0x20000000>; /* 512 MB */ > + }; > + > + vbat: fixedregulator@0 { > + compatible = "regulator-fixed"; > + regulator-name = "vbat"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-boot-on; > + }; I suppose this is the 5V on a power jack, or something like that ? > + vmmcsd_fixed: fixedregulator@0 { > + compatible = "regulator-fixed"; > + regulator-name = "vmmcsd_fixed"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; but this... I know every other board devices this as a fixed regulator, but is it really a fixed regulator or is supplied by one of the LDOs on the PMIC ? > + }; > +}; > + > +&am33xx_pinmux { > + mmc1_pins: pinmux_mmc1_pins { > + pinctrl-single,pins = < > + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3 */ > + 0xf4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2 */ > + 0xf8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1 */ > + 0xfc (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0 */ > + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk */ > + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd */ > + >; > + }; > + > + i2c0_pins: pinmux_i2c0_pins { > + pinctrl-single,pins = < > + 0x188 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */ > + 0x18c (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */ > + >; > + }; > + > + i2c2_pins: pinmux_i2c2_pins { > + pinctrl-single,pins = < > + 0x178 (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_ctsn.i2c2_sda */ > + 0x17c (PIN_INPUT_PULLUP | MUX_MODE3) /* uart1_rtsn.i2c2_scl */ on thing to keep in mind, if you already have external pullups, you might not want to add internal pullups as you'd end up with both resistors in parallel. For I2C the danger is minimal (unless you have a ton of bus capacitance, then it changes high/low time), but it's best to write a more "pristine" DTS. (and sure, I know pretty much every board makes this mistake, but it's best if we don't proliferate the error) > +&i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c0_pins>; > + > + status = "okay"; > + clock-frequency = <400000>; > + > + serial_config1: serial_config1@20 { > + compatible = "nxp,pca9539"; > + reg = <0x20>; > + }; > + > + serial_config2: serial_config2@21 { > + compatible = "nxp,pca9539"; > + reg = <0x21>; > + }; > + > + tps: tps@2d { > + reg = <0x2d>; which TPS device ? no compatible ? > +/include/ "tps65910.dtsi" oh... okay. > +&tps { > + vcc1-supply = <&vbat>; > + vcc2-supply = <&vbat>; > + vcc3-supply = <&vbat>; > + vcc4-supply = <&vbat>; > + vcc5-supply = <&vbat>; > + vcc6-supply = <&vbat>; > + vcc7-supply = <&vbat>; > + vccio-supply = <&vbat>; > + > + regulators { > + vrtc_reg: regulator@0 { > + regulator-always-on; this should not be always on, you want to pass this as supply to the RTC module so it can manage it. It's also best to give names to all regulators, so people know what they're used for. > + }; > + > + vio_reg: regulator@1 { > + regulator-always-on; > + }; > + > + vdd1_reg: regulator@2 { > + regulator-name = "vdd_mpu"; > + regulator-min-microvolt = <600000>; > + regulator-max-microvolt = <1500000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vdd2_reg: regulator@3 { > + regulator-always-on; > + }; > + > + vdd3_reg: regulator@4 { > + regulator-always-on; > + }; > + > + vdig1_reg: regulator@5 { > + regulator-always-on; > + }; > + > + vdig2_reg: regulator@6 { > + regulator-always-on; > + }; > + > + vpll_reg: regulator@7 { > + regulator-always-on; > + }; > + > + vdac_reg: regulator@8 { > + regulator-always-on; > + }; > + > + vaux1_reg: regulator@9 { > + regulator-always-on; > + }; > + > + vaux2_reg: regulator@10 { > + regulator-always-on; > + }; > + > + vaux33_reg: regulator@11 { isn't this the supply to the other MMC slot ? > + regulator-always-on; > + }; > + > + vmmc_reg: regulator@12 { > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + }; > +}; > + > +&sham { > + status = "okay"; > +}; > + > +&aes { > + status = "okay"; > +}; just making sure, are you really using them ? > +&mmc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc1_pins>; > + bus-width = <4>; > + status = "okay"; > + vmmc-supply = <&vmmc_reg>; > + ti,vcc-aux-disable-is-sleep; this binding isn't documented anywhere. What was it supposed to do ? -- balbi
Attachment:
signature.asc
Description: Digital signature
