From: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> A lot of these comments added very little that was not obvious from the register/field name. In one case the polarity was the opposite of what would be expected so rename that field (currently unused in the driver) Signed-off-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx> --- drivers/staging/iio/accel/adis16203.c | 71 +-------------------------- 1 file changed, 1 insertion(+), 70 deletions(-) diff --git a/drivers/staging/iio/accel/adis16203.c b/drivers/staging/iio/accel/adis16203.c index dd02ceb00d40..60117aaf56d4 100644 --- a/drivers/staging/iio/accel/adis16203.c +++ b/drivers/staging/iio/accel/adis16203.c @@ -15,111 +15,42 @@ #define ADIS16203_STARTUP_DELAY 220 /* ms */ -/* Flash memory write count */ #define ADIS16203_FLASH_CNT 0x00 - -/* Output, power supply */ #define ADIS16203_SUPPLY_OUT 0x02 - -/* Output, auxiliary ADC input */ #define ADIS16203_AUX_ADC 0x08 - -/* Output, temperature */ #define ADIS16203_TEMP_OUT 0x0A - -/* Output, x-axis inclination */ #define ADIS16203_XINCL_OUT 0x0C - -/* Output, y-axis inclination */ #define ADIS16203_YINCL_OUT 0x0E - -/* Incline null calibration */ #define ADIS16203_INCL_NULL 0x18 - -/* Alarm 1 amplitude threshold */ #define ADIS16203_ALM_MAG1 0x20 - -/* Alarm 2 amplitude threshold */ #define ADIS16203_ALM_MAG2 0x22 - -/* Alarm 1, sample period */ #define ADIS16203_ALM_SMPL1 0x24 - -/* Alarm 2, sample period */ #define ADIS16203_ALM_SMPL2 0x26 - -/* Alarm control */ #define ADIS16203_ALM_CTRL 0x28 - -/* Auxiliary DAC data */ #define ADIS16203_AUX_DAC 0x30 - -/* General-purpose digital input/output control */ #define ADIS16203_GPIO_CTRL 0x32 - -/* Miscellaneous control */ #define ADIS16203_MSC_CTRL 0x34 - -/* Internal sample period (rate) control */ #define ADIS16203_SMPL_PRD 0x36 - -/* Operation, filter configuration */ #define ADIS16203_AVG_CNT 0x38 - -/* Operation, sleep mode control */ #define ADIS16203_SLP_CNT 0x3A - -/* Diagnostics, system status register */ #define ADIS16203_DIAG_STAT 0x3C - -/* Operation, system command register */ #define ADIS16203_GLOB_CMD 0x3E -/* MSC_CTRL */ - -/* Self-test at power-on: 1 = disabled, 0 = enabled */ -#define ADIS16203_MSC_CTRL_PWRUP_SELF_TEST BIT(10) - -/* Reverses rotation of both inclination outputs */ +#define ADIS16203_MSC_CTRL_PWRUP_SELF_TEST_DIS BIT(10) #define ADIS16203_MSC_CTRL_REVERSE_ROT_EN BIT(9) - -/* Self-test enable */ #define ADIS16203_MSC_CTRL_SELF_TEST_EN BIT(8) - -/* Data-ready enable: 1 = enabled, 0 = disabled */ #define ADIS16203_MSC_CTRL_DATA_RDY_EN BIT(2) - -/* Data-ready polarity: 1 = active high, 0 = active low */ #define ADIS16203_MSC_CTRL_ACTIVE_HIGH BIT(1) - -/* Data-ready line selection: 1 = DIO1, 0 = DIO0 */ #define ADIS16203_MSC_CTRL_DATA_RDY_DIO1 BIT(0) -/* DIAG_STAT */ - -/* Alarm 2 status: 1 = alarm active, 0 = alarm inactive */ #define ADIS16203_DIAG_STAT_ALARM2 BIT(9) - -/* Alarm 1 status: 1 = alarm active, 0 = alarm inactive */ #define ADIS16203_DIAG_STAT_ALARM1 BIT(8) - -/* Self-test diagnostic error flag */ #define ADIS16203_DIAG_STAT_SELFTEST_FAIL_BIT 5 - -/* SPI communications failure */ #define ADIS16203_DIAG_STAT_SPI_FAIL_BIT 3 - -/* Flash update failure */ #define ADIS16203_DIAG_STAT_FLASH_UPT_BIT 2 - -/* Power supply above 3.625 V */ #define ADIS16203_DIAG_STAT_POWER_HIGH_BIT 1 - -/* Power supply below 2.975 V */ #define ADIS16203_DIAG_STAT_POWER_LOW_BIT 0 -/* GLOB_CMD */ - #define ADIS16203_GLOB_CMD_SW_RESET BIT(7) #define ADIS16203_GLOB_CMD_CLEAR_STAT BIT(4) #define ADIS16203_GLOB_CMD_FACTORY_CAL BIT(1) -- 2.39.1
