Re: [PATCH v7 5/7] media: i2c: add DS90UB960 driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 25/01/2023 14:10, Andy Shevchenko wrote:
On Wed, Jan 25, 2023 at 01:15:34PM +0200, Tomi Valkeinen wrote:
On 20/01/2023 18:47, Andy Shevchenko wrote:

...

Esp. taking into account that some of them are using actually
post-inc. Why this difference?

Possibly a different person has written that particular piece of code, or
maybe a copy paste from somewhere.

I'm personally fine with seeing both post and pre increments in code.

I'm not :-), if it's not required by the code. Pre-increment always puzzles
me: Is here anything I have to pay an additional attention to?

That is interesting, as to me pre-increment is the simpler, more obvious
case. It's just:

v = v + 1
v

Whereas post-increment is:

temp = v
v = v + 1
temp

In any case, we're side-tracking here, I think =).

Yes, just see the statistics of use below.

...

+	for (nport = 0; nport < priv->hw_data->num_rxports; ++nport) {

Post-inc?

I still like pre-inc =).

I see there's a mix os post and pre incs in the code. I'll align those when
I encounter them, but I don't think it's worth the effort to methodically go
through all of them to change them use the same style.

Kernel uses post-inc is an idiom for loops:

$ git grep -n -w '[_a-z0-9]\+++' | wc -l
148693

$ git grep -n -w ' ++[a-z0-9_]\+' | wc -l
8701

So, non-standard pattern needs to be explained.

+	}

...

+	ret = fwnode_property_read_u32(link_fwnode, "ti,eq-level", &eq_level);
+	if (ret) {
+		if (ret != -EINVAL) {
+			dev_err(dev, "rx%u: failed to read 'ti,eq-level': %d\n",
+				nport, ret);
+			return ret;
+		}

This seems like trying to handle special cases, if you want it to be optional,
why not ignoring all errors?

I don't follow. Why would we ignore all errors even if the property is
optional? If there's a failure in reading the property, or checking if it
exists or not, surely that's an actual error to be handled, not to be
ignored?

What the problem to ignore them?

Well, probably nothing will explode if we just ignore them. But... Why would we ignore them?

But if you are really pedantic about it, perhaps the proper way is to add

fwnode_property_*_optional()

APIs to the set where you take default and return 0 in case default had been
used for the absent property.

Perhaps, but I don't have a default value here.

In any case, I'm not quite sure what you are arguing here. Is it just that you don't think the error check is necessary and should be dropped?

+	} else if (eq_level > UB960_MAX_EQ_LEVEL) {
+		dev_err(dev, "rx%u: illegal 'ti,eq-level' value: %d\n", nport,
+			eq_level);

This part is a validation of DT again, but we discussed above this.

+	} else {
+		rxport->eq.manual_eq = true;
+		rxport->eq.manual.eq_level = eq_level;
+	}

...

+struct ds90ub9xx_platform_data {
+	u32 port;
+	struct i2c_atr *atr;
+	unsigned long bc_rate;

Not sure why we need this to be public except, probably, atr...

The port and atr are used by the serializers, for atr. The bc_rate is used
by the serializers to figure out the clocking (they may use the FPD-Link's
frequency internally).

The plain numbers can be passed as device properties. That's why the question
about platform data. Platform data in general is discouraged to be used in a
new code.

Device properties, as in, coming from DT?

 From anywhere.

The port could be in the DT, but
the others are not hardware properties.

Why do we need them? For example, bc_rate.

The atr pointer is needed so that the serializers (ub913, ub953) can add their i2c adapter to the deserializer's i2c-atr. The port is also needed for that.

The bc rate (back-channel rate) is the FPD-Link back-channel rate which the serializers use for various functionalities. At the moment only the ub953 uses it for calculating an output clock rate.

The bc-rate could be implemented using the clock framework, even if it's not quite a plain clock. I had that code at some point, but it felt a bit off and as we needed the pdata for the ATR, I added the bc-rate there.

Yes, I don't like using platform data. We need some way to pass information
between the drivers.

Device properties allow that and targeting to remove the legacy platform data
in zillions of the drivers.

Do you have any pointers to guide me into the right direction? I couldn't find anything with some grepping and googling.

If you mean "device properties" as in ACPI, and so similar to DT properties, aren't those hardware properties? Only the port here is about the hardware.

 Tomi




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux