On Fri, 20 Jan 2023 17:39:17 +0100 Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx> wrote: > Hello, > > On 07/01/2023 19:36:06+0100, Bruno Thomsen wrote: > > Den tor. 15. dec. 2022 kl. 16.19 skrev Hugo Villeneuve <hugo@xxxxxxxxxxx>: > > > > > > From: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx> > > > > > > Default PWRMNG[2:0] bits are set to 000b for PCF2127/29, but to > > > 111b for PCF2131. > > > > > > Set these bits to 000b to select same mode as PCF2127/29. > > > > > > Signed-off-by: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx> > > > > Reviewed-by: Bruno Thomsen <bruno.thomsen@xxxxxxxxx> > > > > I think it's a good idea[1] but there have been concerns about > > setting default values in the past[2]. In case somebody needs > > a different behaviour they should add a device tree property. > > > > [1] https://lore.kernel.org/linux-rtc/20190910143945.9364-1-bruno.thomsen@xxxxxxxxx/ > > [2] https://lore.kernel.org/linux-rtc/20191211163354.GC1463890@xxxxxxxxx/ > > I confirm this is still my point of view and I won't take this patch as > this may break existing users. Patch dropped. > > > > > --- > > > drivers/rtc/rtc-pcf2127.c | 15 +++++++++++++++ > > > 1 file changed, 15 insertions(+) > > > > > > diff --git a/drivers/rtc/rtc-pcf2127.c b/drivers/rtc/rtc-pcf2127.c > > > index 68af4d0438b8..241189ee4a05 100644 > > > --- a/drivers/rtc/rtc-pcf2127.c > > > +++ b/drivers/rtc/rtc-pcf2127.c > > > @@ -53,6 +53,7 @@ > > > #define PCF2127_BIT_CTRL3_BLF BIT(2) > > > #define PCF2127_BIT_CTRL3_BF BIT(3) > > > #define PCF2127_BIT_CTRL3_BTSE BIT(4) > > > +#define PCF2127_CTRL3_PWRMNG_MASK GENMASK(7, 5) > > > /* Control register 4 */ > > > #define PCF2131_REG_CTRL4 0x03 > > > #define PCF2131_BIT_CTRL4_TSF4 BIT(4) > > > @@ -1129,6 +1130,20 @@ static int pcf2127_probe(struct device *dev, struct regmap *regmap, > > > regmap_clear_bits(pcf2127->regmap, PCF2127_REG_CTRL1, > > > PCF2127_BIT_CTRL1_POR_OVRD); > > > > > > + /* Make sure PWRMNG[2:0] is set to 000b. This is the default for > > > + * PCF2127/29, but not for PCF2131 (default of 111b). > > > + * > > > + * PWRMNG[2:0] = 000b: > > > + * battery switch-over function is enabled in standard mode; > > > + * battery low detection function is enabled > > > + */ > > > + ret = regmap_clear_bits(pcf2127->regmap, PCF2127_REG_CTRL3, > > > + PCF2127_CTRL3_PWRMNG_MASK); > > > + if (ret < 0) { > > > + dev_err(dev, "PWRMNG config failed\n"); > > > + return ret; > > > + } > > > + > > > ret = regmap_read(pcf2127->regmap, pcf2127->cfg->reg_clkout, &val); > > > if (ret < 0) > > > return ret; > > > -- > > > 2.30.2 > > > > > -- > Alexandre Belloni, co-owner and COO, Bootlin > Embedded Linux and Kernel engineering > https://bootlin.com > -- Hugo Villeneuve <hugo@xxxxxxxxxxx>
