Re: [PATCH 2/2] drm/panel: st7703: Add support for Anbernic RG353V-V2 panel

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Jan 20, 2023 at 10:06:48AM +0100, Guido Günther wrote:
> Hi,
> On Thu, Jan 19, 2023 at 05:04:15PM -0600, Chris Morgan wrote:
> > From: Chris Morgan <macromorgan@xxxxxxxxxxx>
> > 
> > The Anbernic RG353V-V2 is a 5 inch panel used in a new revision of the
> > Anbernic RG353V handheld gaming device. Add support for it.
> > 
> > Unfortunately it appears this controller is not able to support 120hz
> > or 100hz mode like the first revision panel.
> > 
> > Signed-off-by: Chris Morgan <macromorgan@xxxxxxxxxxx>
> > ---
> >  drivers/gpu/drm/panel/panel-sitronix-st7703.c | 102 +++++++++++++++++-
> >  1 file changed, 99 insertions(+), 3 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/panel/panel-sitronix-st7703.c b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> > index 86a472b01360..2ed0cdfa86de 100644
> > --- a/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> > +++ b/drivers/gpu/drm/panel/panel-sitronix-st7703.c
> > @@ -28,6 +28,7 @@
> >  /* Manufacturer specific Commands send via DSI */
> >  #define ST7703_CMD_ALL_PIXEL_OFF 0x22
> >  #define ST7703_CMD_ALL_PIXEL_ON	 0x23
> > +#define ST7703_CMD_SETAPID	 0xB1
> >  #define ST7703_CMD_SETDISP	 0xB2
> >  #define ST7703_CMD_SETRGBIF	 0xB3
> >  #define ST7703_CMD_SETCYC	 0xB4
> > @@ -41,12 +42,15 @@
> >  #define ST7703_CMD_UNKNOWN_BF	 0xBF
> >  #define ST7703_CMD_SETSCR	 0xC0
> >  #define ST7703_CMD_SETPOWER	 0xC1
> > +#define ST7703_CMD_SETECO	 0xC6
> > +#define ST7703_CMD_SETIO	 0xC7
> > +#define ST7703_CMD_SETCABC	 0xC8
> >  #define ST7703_CMD_SETPANEL	 0xCC
> > -#define ST7703_CMD_UNKNOWN_C6	 0xC6
> >  #define ST7703_CMD_SETGAMMA	 0xE0
> >  #define ST7703_CMD_SETEQ	 0xE3
> >  #define ST7703_CMD_SETGIP1	 0xE9
> >  #define ST7703_CMD_SETGIP2	 0xEA
> > +#define ST7703_CMD_UNKNOWN_EF	 0xEF
> >  
> >  struct st7703 {
> >  	struct device *dev;
> > @@ -266,8 +270,7 @@ static int xbd599_init_sequence(struct st7703 *ctx)
> >  				 * ESD_DET_TIME_SEL = 0 frames
> >  				 */);
> >  
> > -	/* Undocumented command. */
> > -	dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_C6, 0x01, 0x00, 0xFF, 0xFF, 0x00);
> > +	dsi_dcs_write_seq(dsi, ST7703_CMD_SETECO, 0x01, 0x00, 0xFF, 0xFF, 0x00);
> 
> Thanks for catching this! Would make sense to split that into a separate
> commit. With that fixed

I can, if you would prefer. I just thought it was trivial so I wrapped
it up in a single commit. I had a newer revision of the ST7703
datasheet on hand that had that command documented, but unfortunately
not BF or a new command I added EF. If a new commit is preferred I'll
resubmit early next week.

Thank you.

> 
> Reviewed-by: Guido Günther <agx@xxxxxxxxxxx>
> 
>  -- Guido
> 
> >  
> >  	dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER,
> >  			  0x74, /* VBTHS, VBTLS: VGH = 17V, VBL = -11V */
> > @@ -355,6 +358,98 @@ static const struct st7703_panel_desc xbd599_desc = {
> >  	.init_sequence = xbd599_init_sequence,
> >  };
> >  
> > +static int rg353v2_init_sequence(struct st7703 *ctx)
> > +{
> > +	struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
> > +
> > +	/*
> > +	 * Init sequence was supplied by the panel vendor.
> > +	 */
> > +
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETEXTC, 0xf1, 0x12, 0x83);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETAPID, 0x00, 0x00, 0x00,
> > +			       0xda, 0x80);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETDISP, 0x00, 0x13, 0x70);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETRGBIF, 0x10, 0x10, 0x28,
> > +			       0x28, 0x03, 0xff, 0x00, 0x00, 0x00, 0x00);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETCYC, 0x80);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETBGP, 0x0a, 0x0a);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETVCOM, 0x92, 0x92);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER_EXT, 0x25, 0x22,
> > +			       0xf0, 0x63);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETMIPI, 0x33, 0x81, 0x05,
> > +			       0xf9, 0x0e, 0x0e, 0x20, 0x00, 0x00, 0x00, 0x00,
> > +			       0x00, 0x00, 0x00, 0x44, 0x25, 0x00, 0x90, 0x0a,
> > +			       0x00, 0x00, 0x01, 0x4f, 0x01, 0x00, 0x00, 0x37);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETVDC, 0x47);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_BF, 0x02, 0x11, 0x00);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETSCR, 0x73, 0x73, 0x50, 0x50,
> > +			       0x00, 0x00, 0x12, 0x50, 0x00);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETPOWER, 0x53, 0xc0, 0x32,
> > +			       0x32, 0x77, 0xe1, 0xdd, 0xdd, 0x77, 0x77, 0x33,
> > +			       0x33);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETECO, 0x82, 0x00, 0xbf, 0xff,
> > +			       0x00, 0xff);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETIO, 0xb8, 0x00, 0x0a, 0x00,
> > +			       0x00, 0x00);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETCABC, 0x10, 0x40, 0x1e,
> > +			       0x02);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETPANEL, 0x0b);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETGAMMA, 0x00, 0x07, 0x0d,
> > +			       0x37, 0x35, 0x3f, 0x41, 0x44, 0x06, 0x0c, 0x0d,
> > +			       0x0f, 0x11, 0x10, 0x12, 0x14, 0x1a, 0x00, 0x07,
> > +			       0x0d, 0x37, 0x35, 0x3f, 0x41, 0x44, 0x06, 0x0c,
> > +			       0x0d, 0x0f, 0x11, 0x10, 0x12, 0x14, 0x1a);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETEQ, 0x07, 0x07, 0x0b, 0x0b,
> > +			       0x0b, 0x0b, 0x00, 0x00, 0x00, 0x00, 0xff, 0x00,
> > +			       0xc0, 0x10);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP1, 0xc8, 0x10, 0x02, 0x00,
> > +			       0x00, 0xb0, 0xb1, 0x11, 0x31, 0x23, 0x28, 0x80,
> > +			       0xb0, 0xb1, 0x27, 0x08, 0x00, 0x04, 0x02, 0x00,
> > +			       0x00, 0x00, 0x00, 0x04, 0x02, 0x00, 0x00, 0x00,
> > +			       0x88, 0x88, 0xba, 0x60, 0x24, 0x08, 0x88, 0x88,
> > +			       0x88, 0x88, 0x88, 0x88, 0x88, 0xba, 0x71, 0x35,
> > +			       0x18, 0x88, 0x88, 0x88, 0x88, 0x88, 0x00, 0x00,
> > +			       0x00, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > +			       0x00, 0x00, 0x00);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_SETGIP2, 0x97, 0x0a, 0x82, 0x02,
> > +			       0x03, 0x07, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > +			       0x81, 0x88, 0xba, 0x17, 0x53, 0x88, 0x88, 0x88,
> > +			       0x88, 0x88, 0x88, 0x80, 0x88, 0xba, 0x06, 0x42,
> > +			       0x88, 0x88, 0x88, 0x88, 0x88, 0x88, 0x23, 0x00,
> > +			       0x00, 0x02, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00,
> > +			       0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > +			       0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
> > +			       0x00);
> > +	mipi_dsi_dcs_write_seq(dsi, ST7703_CMD_UNKNOWN_EF, 0xff, 0xff, 0x01);
> > +
> > +	return 0;
> > +}
> > +
> > +static const struct drm_display_mode rg353v2_mode = {
> > +	.hdisplay	= 640,
> > +	.hsync_start	= 640 + 40,
> > +	.hsync_end	= 640 + 40 + 2,
> > +	.htotal		= 640 + 40 + 2 + 80,
> > +	.vdisplay	= 480,
> > +	.vsync_start	= 480 + 18,
> > +	.vsync_end	= 480 + 18 + 2,
> > +	.vtotal		= 480 + 18 + 2 + 28,
> > +	.clock		= 24150,
> > +	.flags		= DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> > +	.width_mm	= 70,
> > +	.height_mm	= 57,
> > +};
> > +
> > +static const struct st7703_panel_desc rg353v2_desc = {
> > +	.mode = &rg353v2_mode,
> > +	.lanes = 4,
> > +	.mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
> > +		      MIPI_DSI_MODE_NO_EOT_PACKET | MIPI_DSI_MODE_LPM,
> > +	.format = MIPI_DSI_FMT_RGB888,
> > +	.init_sequence = rg353v2_init_sequence,
> > +};
> > +
> >  static int st7703_enable(struct drm_panel *panel)
> >  {
> >  	struct st7703 *ctx = panel_to_st7703(panel);
> > @@ -615,6 +710,7 @@ static void st7703_remove(struct mipi_dsi_device *dsi)
> >  }
> >  
> >  static const struct of_device_id st7703_of_match[] = {
> > +	{ .compatible = "anbernic,rg353v-panel-v2", .data = &rg353v2_desc },
> >  	{ .compatible = "rocktech,jh057n00900", .data = &jh057n00900_panel_desc },
> >  	{ .compatible = "xingbangda,xbd599", .data = &xbd599_desc },
> >  	{ /* sentinel */ }
> > -- 
> > 2.34.1
> > 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux