This is a driver for the Amlogic Meson SPIFC (SPI flash controller), which is one of the two SPI controllers available on the SoC. It doesn't support DMA and has a 64-byte unified transmit/receive buffer. The device is optimized for interfacing with SPI NOR memories and allows the execution of standard operations such as read, page program, sector erase, etc. in a simplified way, basically toggling a bit in a dedicated register. The driver doesn't use those predefined commands and relies only on custom transfers. Signed-off-by: Beniamino Galvani <b.galvani@xxxxxxxxx> --- drivers/spi/Kconfig | 7 + drivers/spi/Makefile | 1 + drivers/spi/spi-meson-spifc.c | 411 ++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 419 insertions(+) create mode 100644 drivers/spi/spi-meson-spifc.c diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 84e7c9e..3c98a9d 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -301,6 +301,13 @@ config SPI_FSL_ESPI From MPC8536, 85xx platform uses the controller, and all P10xx, P20xx, P30xx,P40xx, P50xx uses this controller. +config SPI_MESON_SPIFC + bool "Amlogic Meson SPIFC controller" + depends on ARCH_MESON + help + This enables master mode support for the SPIFC (SPI flash + controller) available in Amlogic Meson SoCs. + config SPI_OC_TINY tristate "OpenCores tiny SPI" depends on GPIOLIB diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 78f24ca..9b8a747 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -42,6 +42,7 @@ obj-$(CONFIG_SPI_FSL_SPI) += spi-fsl-spi.o obj-$(CONFIG_SPI_GPIO) += spi-gpio.o obj-$(CONFIG_SPI_IMX) += spi-imx.o obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o +obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mpc512x-psc.o obj-$(CONFIG_SPI_MPC52xx_PSC) += spi-mpc52xx-psc.o obj-$(CONFIG_SPI_MPC52xx) += spi-mpc52xx.o diff --git a/drivers/spi/spi-meson-spifc.c b/drivers/spi/spi-meson-spifc.c new file mode 100644 index 0000000..a0ba5d8 --- /dev/null +++ b/drivers/spi/spi-meson-spifc.c @@ -0,0 +1,411 @@ +/* + * Driver for Amlogic Meson SPI flash controller (SPIFC) + * + * Copyright (C) 2014 Beniamino Galvani <b.galvani@xxxxxxxxx> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/spi/spi.h> +#include <linux/types.h> + +/* register map */ +#define REG_CMD 0x00 +#define REG_ADDR 0x04 +#define REG_CTRL 0x08 +#define REG_CTRL1 0x0c +#define REG_STATUS 0x10 +#define REG_CTRL2 0x14 +#define REG_CLOCK 0x18 +#define REG_USER 0x1c +#define REG_USER1 0x20 +#define REG_USER2 0x24 +#define REG_USER3 0x28 +#define REG_USER4 0x2c +#define REG_SLAVE 0x30 +#define REG_SLAVE1 0x34 +#define REG_SLAVE2 0x38 +#define REG_SLAVE3 0x3c +#define REG_C0 0x40 +#define REG_B8 0x60 + +/* register fields */ +#define CMD_USER BIT(18) +#define CTRL_ENABLE_AHB BIT(17) +#define CLOCK_SOURCE BIT(31) +#define CLOCK_DIV_SHIFT 12 +#define CLOCK_DIV_MASK (0x3f << CLOCK_DIV_SHIFT) +#define CLOCK_CNT_HIGH_SHIFT 6 +#define CLOCK_CNT_HIGH_MASK (0x3f << CLOCK_CNT_HIGH_SHIFT) +#define CLOCK_CNT_LOW_SHIFT 0 +#define CLOCK_CNT_LOW_MASK (0x3f << CLOCK_CNT_LOW_SHIFT) +#define USER_DIN_EN_MS BIT(0) +#define USER_CMP_MODE BIT(2) +#define USER_UC_DOUT_SEL BIT(27) +#define USER_UC_DIN_SEL BIT(28) +#define USER_UC_MASK ((BIT(5) - 1) << 27) +#define USER1_BN_UC_DOUT_SHIFT 17 +#define USER1_BN_UC_DOUT_MASK (0xff << 16) +#define USER1_BN_UC_DIN_SHIFT 8 +#define USER1_BN_UC_DIN_MASK (0xff << 8) +#define USER4_CS_ACT BIT(30) +#define SLAVE_TRST_DONE BIT(4) +#define SLAVE_OP_MODE BIT(30) +#define SLAVE_SW_RST BIT(31) + +#define SPIFC_BUFFER_SIZE 64 + +/** + * struct meson_spifc + * @master: the SPI master + * @regmap: regmap for device registers + * @clk: input clock of the built-in baud rate generator + * @device: the device structure + */ +struct meson_spifc { + struct spi_master *master; + struct regmap *regmap; + struct clk *clk; + struct device *dev; +}; + +static struct regmap_config spifc_regmap_config = { + .reg_bits = 32, + .val_bits = 32, + .reg_stride = 4, +}; + +/** + * meson_spifc_wait_ready() - wait for the current operation to terminate + * @spifc: the Meson SPI device + * Return: 0 on success, a negative value on error + */ +static int meson_spifc_wait_ready(struct meson_spifc *spifc) +{ + unsigned long deadline = jiffies + msecs_to_jiffies(1000); + u32 data; + + do { + regmap_read(spifc->regmap, REG_SLAVE, &data); + if (data & SLAVE_TRST_DONE) + return 0; + cond_resched(); + } while (time_before(jiffies, deadline)); + + return -ETIMEDOUT; +} + +/** + * meson_spifc_drain_buffer() - copy data from device buffer to memory + * @spifc: the Meson SPI device + * @buf: the destination buffer + * @len: number of bytes to copy + */ +static void meson_spifc_drain_buffer(struct meson_spifc *spifc, u8 *buf, + int len) +{ + u32 data; + int i = 0; + + while (i < len) { + regmap_read(spifc->regmap, REG_C0 + i, &data); + + if (len - i >= 4) { + *((u32 *)buf) = data; + buf += 4; + } else { + memcpy(buf, &data, len - i); + break; + } + i += 4; + } +} + +/** + * meson_spifc_fill_buffer() - copy data from memory to device buffer + * @spifc: the Meson SPI device + * @buf: the source buffer + * @len: number of bytes to copy + */ +static void meson_spifc_fill_buffer(struct meson_spifc *spifc, const u8 *buf, + int len) +{ + u32 data; + int i = 0; + + while (i < len) { + if (len - i >= 4) + data = *(u32 *)buf; + else + memcpy(&data, buf, len - i); + + regmap_write(spifc->regmap, REG_C0 + i, data); + + buf += 4; + i += 4; + } +} + +/** + * meson_spifc_setup_speed() - program the clock divider + * @spifc: the Meson SPI device + * @speed: desired speed in Hz + */ +void meson_spifc_setup_speed(struct meson_spifc *spifc, u32 speed) +{ + unsigned long parent, value; + int n; + + parent = clk_get_rate(spifc->clk); + n = max_t(int, parent / speed - 1, 1); + + dev_dbg(spifc->dev, "parent %lu, speed %u, n %d\n", parent, + speed, n); + + value = (n << CLOCK_DIV_SHIFT) & CLOCK_DIV_MASK; + value |= (n << CLOCK_CNT_LOW_SHIFT) & CLOCK_CNT_LOW_MASK; + value |= (((n + 1) / 2 - 1) << CLOCK_CNT_HIGH_SHIFT) & + CLOCK_CNT_HIGH_MASK; + + regmap_write(spifc->regmap, REG_CLOCK, value); +} + +/** + * meson_spifc_txrx() - transfer a chunk of data + * @spifc: the Meson SPI device + * @xfer: the current SPI transfer + * @offset: offset of the data to transfer + * @len: length of the data to transfer + * @last_xfer: whether this is the last transfer of the message + * @last_chunk: whether this is the last chunk of the transfer + * Return: 0 on success, a negative value on error + */ +static int meson_spifc_txrx(struct meson_spifc *spifc, + struct spi_transfer *xfer, + int offset, int len, bool last_xfer, + bool last_chunk) +{ + bool keep_cs = true; + int ret; + + if (xfer->tx_buf) + meson_spifc_fill_buffer(spifc, xfer->tx_buf + offset, len); + + /* enable DOUT stage */ + regmap_update_bits(spifc->regmap, REG_USER, USER_UC_MASK, + USER_UC_DOUT_SEL); + regmap_write(spifc->regmap, REG_USER1, + (8 * len - 1) << USER1_BN_UC_DOUT_SHIFT); + + /* enable data input during DOUT */ + regmap_update_bits(spifc->regmap, REG_USER, USER_DIN_EN_MS, + USER_DIN_EN_MS); + + if (last_chunk) { + if (last_xfer) + keep_cs = xfer->cs_change; + else + keep_cs = !xfer->cs_change; + } + + regmap_update_bits(spifc->regmap, REG_USER4, USER4_CS_ACT, + keep_cs ? USER4_CS_ACT : 0); + + /* clear transition done bit */ + regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_TRST_DONE, 0); + /* start transfer */ + regmap_update_bits(spifc->regmap, REG_CMD, CMD_USER, CMD_USER); + + ret = meson_spifc_wait_ready(spifc); + + if (!ret && xfer->rx_buf) + meson_spifc_drain_buffer(spifc, xfer->rx_buf + offset, len); + + return ret; +} + +/** + * meson_spifc_transfer_one() - perform a single transfer + * @spifc: the Meson SPI device + * @xfer: the current SPI transfer + * @last_xfer: whether this is the last transfer of the message + * Return: 0 on success, a negative value on error + */ +static int meson_spifc_transfer_one(struct spi_device *spi, + struct spi_transfer *xfer, + bool last_xfer) +{ + struct meson_spifc *spifc = spi_master_get_devdata(spi->master); + int len, done = 0, ret = 0; + + meson_spifc_setup_speed(spifc, xfer->speed_hz ? xfer->speed_hz : + spi->max_speed_hz); + + regmap_update_bits(spifc->regmap, REG_CTRL, CTRL_ENABLE_AHB, 0); + + while (done < xfer->len && !ret) { + len = min_t(int, xfer->len - done, SPIFC_BUFFER_SIZE); + ret = meson_spifc_txrx(spifc, xfer, done, len, + last_xfer, done + len >= xfer->len); + done += len; + } + + regmap_update_bits(spifc->regmap, REG_CTRL, CTRL_ENABLE_AHB, + CTRL_ENABLE_AHB); + + if (!ret && xfer->delay_usecs) + udelay(xfer->delay_usecs); + + return ret; +} + +/** + * meson_spifc_transfer_one_message() - transfer a single SPI message + * @master: the SPI master + * @msg: the message to transfer + * Return: 0 on success, a negative value on error + */ +static int meson_spifc_transfer_one_message(struct spi_master *master, + struct spi_message *msg) +{ + struct spi_transfer *xfer; + int ret = 0; + bool last; + + list_for_each_entry(xfer, &msg->transfers, transfer_list) { + last = list_is_last(&xfer->transfer_list, &msg->transfers); + ret = meson_spifc_transfer_one(msg->spi, xfer, last); + if (ret) + break; + msg->actual_length += xfer->len; + } + + msg->status = ret; + spi_finalize_current_message(master); + + return ret; +} + +static int meson_spifc_probe(struct platform_device *pdev) +{ + struct spi_master *master; + struct meson_spifc *spifc; + struct resource *res; + void __iomem *base; + unsigned int rate; + int ret = 0; + + master = spi_alloc_master(&pdev->dev, sizeof(struct meson_spifc)); + if (!master) + return -ENOMEM; + + platform_set_drvdata(pdev, master); + + spifc = spi_master_get_devdata(master); + memset(spifc, 0, sizeof(struct meson_spifc)); + spifc->dev = &pdev->dev; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + base = devm_ioremap_resource(spifc->dev, res); + if (IS_ERR(base)) { + ret = PTR_ERR(base); + goto out_err; + } + + spifc_regmap_config.max_register = resource_size(res) - 4; + spifc_regmap_config.name = "amlogic,meson-spifc"; + spifc->regmap = devm_regmap_init_mmio(spifc->dev, base, + &spifc_regmap_config); + if (IS_ERR(spifc->regmap)) { + ret = PTR_ERR(spifc->regmap); + goto out_err; + } + + spifc->clk = devm_clk_get(spifc->dev, NULL); + if (IS_ERR(spifc->clk)) { + dev_err(spifc->dev, "missing clock\n"); + ret = PTR_ERR(spifc->clk); + goto out_err; + } + + ret = clk_prepare_enable(spifc->clk); + if (ret) { + dev_err(spifc->dev, "can't prepare clock\n"); + goto out_err; + } + + rate = clk_get_rate(spifc->clk); + + master->bus_num = pdev->id; + master->num_chipselect = 1; + master->dev.of_node = pdev->dev.of_node; + master->bits_per_word_mask = SPI_BPW_MASK(8); + master->transfer_one_message = meson_spifc_transfer_one_message; + master->min_speed_hz = rate >> 6; + master->max_speed_hz = rate >> 1; + + /* reset device */ + regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_SW_RST, + SLAVE_SW_RST); + /* disable compatible mode */ + regmap_update_bits(spifc->regmap, REG_USER, USER_CMP_MODE, 0); + /* set master mode */ + regmap_update_bits(spifc->regmap, REG_SLAVE, SLAVE_OP_MODE, 0); + + ret = devm_spi_register_master(&pdev->dev, master); + if (ret) { + dev_err(spifc->dev, "failed to register spi master\n"); + goto out_clk; + } + + return 0; +out_clk: + clk_disable_unprepare(spifc->clk); +out_err: + spi_master_put(master); + return ret; +} + +static int meson_spifc_remove(struct platform_device *pdev) +{ + struct spi_master *master = platform_get_drvdata(pdev); + struct meson_spifc *spifc = spi_master_get_devdata(master); + + clk_disable_unprepare(spifc->clk); + + return 0; +} + +static const struct of_device_id meson_spifc_dt_match[] = { + { .compatible = "amlogic,meson6-spifc", }, + { }, +}; + +static struct platform_driver meson_spifc_driver = { + .probe = meson_spifc_probe, + .remove = meson_spifc_remove, + .driver = { + .name = "meson-spifc", + .of_match_table = of_match_ptr(meson_spifc_dt_match), + }, +}; + +module_platform_driver(meson_spifc_driver); + +MODULE_AUTHOR("Beniamino Galvani <b.galvani@xxxxxxxxx>"); +MODULE_DESCRIPTION("Amlogic Meson SPIFC driver"); +MODULE_LICENSE("GPL v2"); -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
