On Sun, Jan 15, 2023 at 05:11:46PM +0530, Krishna Kurapati wrote:
> Add USB and DWC3 node for teritiary port of SC8280 along
> with multiport IRQ's and phy's.
>
Very nice.
Please make the subject prefix "arm64: dts: qcom: sc8280xp:", to match
other changes in the sc8280xp.dtsi.
> Signed-off-by: Krishna Kurapati <quic_kriskura@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 49 +++++++++++++++++++
> arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 60 ++++++++++++++++++++++++
> 2 files changed, 109 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> index 84cb6f3eeb56..f9eb854c3444 100644
> --- a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
> @@ -422,6 +422,20 @@ &usb_1_qmpphy {
> status = "okay";
> };
>
> +&usb_2 {
> + status = "okay";
Please the status property last in the node.
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb2_en_state>,
> + <&usb3_en_state>,
> + <&usb4_en_state>,
> + <&usb5_en_state>;
> +};
> +
> +&usb_2_dwc3 {
> + dr_mode = "host";
> +};
> +
> &usb_2_hsphy0 {
> vdda-pll-supply = <&vreg_l5a>;
> vdda18-supply = <&vreg_l7g>;
> @@ -472,6 +486,41 @@ &xo_board_clk {
> clock-frequency = <38400000>;
> };
>
> +/* PINCTRL */
No need to repeat this comment, its purpose is to indicate that nodes
above are sorted alphabetically and pinctrl-related nodes are kept here
at the end of the file. Please place your nodes below the existing /*
PINCTRL */ comment below.
Thanks,
Bjorn
> +&pm8450c_gpios {
> + usb2_en_state: usb2-en-state {
> + pins = "gpio9";
> + function = "normal";
> + output-high;
> + power-source = <0>;
> + };
> +};
> +
> +&pm8450e_gpios {
> + usb3_en_state: usb3-en-state {
> + pins = "gpio5";
> + function = "normal";
> + output-high;
> + power-source = <0>;
> + };
> +};
> +
> +&pm8450g_gpios {
> + usb4_en_state: usb4-en-state {
> + pins = "gpio5";
> + function = "normal";
> + output-high;
> + power-source = <0>;
> + };
> +
> + usb5_en_state: usb5-en-state {
> + pins = "gpio9";
> + function = "normal";
> + output-high;
> + power-source = <0>;
> + };
> +};
> +
> /* PINCTRL */
>
> &tlmm {
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> index 109c9d2b684d..e9866ab5c6e2 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> @@ -1969,6 +1969,66 @@ usb_1_dwc3: usb@a800000 {
> };
> };
>
> + usb_2: usb@a4f8800 {
> + compatible = "qcom,sc8280xp-dwc3", "qcom,dwc3";
> + reg = <0 0x0a4f8800 0 0x400>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + clocks = <&gcc GCC_CFG_NOC_USB3_MP_AXI_CLK>,
> + <&gcc GCC_USB30_MP_MASTER_CLK>,
> + <&gcc GCC_AGGRE_USB3_MP_AXI_CLK>,
> + <&gcc GCC_USB30_MP_SLEEP_CLK>,
> + <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
> + <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
> + <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
> + <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
> + <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
> + clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
> + "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
> +
> + assigned-clocks = <&gcc GCC_USB30_MP_MOCK_UTMI_CLK>,
> + <&gcc GCC_USB30_MP_MASTER_CLK>;
> + assigned-clock-rates = <19200000>, <200000000>;
> +
> + interrupts-extended = <&pdc 127 IRQ_TYPE_EDGE_RISING>,
> + <&pdc 126 IRQ_TYPE_EDGE_RISING>,
> + <&pdc 16 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupt-names = "dp_hs_phy_irq", "dm_hs_phy_irq",
> + "ss_phy_irq";
> +
> + power-domains = <&gcc USB30_MP_GDSC>;
> +
> + resets = <&gcc GCC_USB30_MP_BCR>;
> +
> + interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI1 0>,
> + <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
> + interconnect-names = "usb-ddr", "apps-usb";
> +
> + required-opps = <&rpmhpd_opp_nom>;
> +
> + status = "disabled";
> +
> + usb_2_dwc3: usb@a400000 {
> + compatible = "snps,dwc3";
> + reg = <0 0x0a400000 0 0xcd00>;
> + interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> + iommus = <&apps_smmu 0x800 0x0>;
> + num-ports = <4>;
> + num-ss-ports = <2>;
> + phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>,
> + <&usb_2_hsphy1>, <&usb_2_qmpphy1>,
> + <&usb_2_hsphy2>,
> + <&usb_2_hsphy3>;
> + phy-names = "usb2-phy_port0", "usb3-phy_port0",
> + "usb2-phy_port1", "usb3-phy_port1",
> + "usb2-phy_port2",
> + "usb2-phy_port3";
> + };
> + };
> +
> pdc: interrupt-controller@b220000 {
> compatible = "qcom,sc8280xp-pdc", "qcom,pdc";
> reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
> --
> 2.39.0
>
