Add devices tree nodes describing display hardware on SM8550:
- Display Clock Controller
- MDSS
- MDP
- two DSI controllers and DSI PHYs
This does not provide support for DP controllers present on the SM8550.
Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sm8550.dtsi | 299 +++++++++++++++++++++++++++++++++++
1 file changed, 299 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 2d9377e01c3f..243fffa19c35 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -6,6 +6,7 @@
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/clock/qcom,sm8550-gcc.h>
#include <dt-bindings/clock/qcom,sm8550-tcsr.h>
+#include <dt-bindings/clock/qcom,sm8550-dispcc.h>
#include <dt-bindings/dma/qcom-gpi.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -1455,6 +1456,304 @@ opp-202000000 {
};
};
+ mdss: display-subsystem@ae00000 {
+ compatible = "qcom,sm8550-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+ resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+ power-domains = <&dispcc MDSS_GDSC>;
+
+ interconnects = <&mmss_noc MASTER_MDP 0 &gem_noc SLAVE_LLCC 0>,
+ <&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "mdp0-mem", "mdp1-mem";
+
+ iommus = <&apps_smmu 0x1c00 0x2>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdss_mdp: display-controller@ae01000 {
+ compatible = "qcom,sm8550-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus",
+ "nrt_bus",
+ "iface",
+ "lut",
+ "core",
+ "vsync";
+
+ power-domains = <&rpmhpd SM8550_MMCX>;
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <19200000>;
+
+ operating-points-v2 = <&mdp_opp_table>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint = <&mdss_dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dpu_intf2_out: endpoint {
+ remote-endpoint = <&mdss_dsi1_in>;
+ };
+ };
+ };
+
+ mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-325000000 {
+ opp-hz = /bits/ 64 <325000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-514000000 {
+ opp-hz = /bits/ 64 <514000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss_dsi0: dsi@ae94000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae94000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ power-domains = <&rpmhpd SM8550_MMCX>;
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+ operating-points-v2 = <&mdss_dsi_opp_table>;
+
+ phys = <&mdss_dsi0_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss_dsi0_in: endpoint {
+ remote-endpoint = <&dpu_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mdss_dsi0_out: endpoint {
+ };
+ };
+ };
+
+ mdss_dsi_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-187500000 {
+ opp-hz = /bits/ 64 <187500000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-358000000 {
+ opp-hz = /bits/ 64 <358000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+ };
+ };
+
+ mdss_dsi0_phy: phy@ae95000 {
+ compatible = "qcom,sm8550-dsi-phy-4nm";
+ reg = <0 0x0ae95000 0 0x200>,
+ <0 0x0ae95200 0 0x280>,
+ <0 0x0ae95500 0 0x400>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ mdss_dsi1: dsi@ae96000 {
+ compatible = "qcom,mdss-dsi-ctrl";
+ reg = <0 0x0ae96000 0 0x400>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5>;
+
+ clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+ <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>;
+ clock-names = "byte",
+ "byte_intf",
+ "pixel",
+ "core",
+ "iface",
+ "bus";
+
+ power-domains = <&rpmhpd SM8550_MMCX>;
+
+ assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>, <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+ assigned-clock-parents = <&mdss_dsi1_phy 0>, <&mdss_dsi1_phy 1>;
+
+ operating-points-v2 = <&mdss_dsi_opp_table>;
+
+ phys = <&mdss_dsi1_phy>;
+ phy-names = "dsi";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss_dsi1_in: endpoint {
+ remote-endpoint = <&dpu_intf2_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mdss_dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ mdss_dsi1_phy: phy@ae97000 {
+ compatible = "qcom,sm8550-dsi-phy-4nm";
+ reg = <0 0x0ae97000 0 0x200>,
+ <0 0x0ae97200 0 0x280>,
+ <0 0x0ae97500 0 0x400>;
+ reg-names = "dsi_phy",
+ "dsi_phy_lane",
+ "dsi_pll";
+
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface", "ref";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+ };
+
+ dispcc: clock-controller@af00000 {
+ compatible = "qcom,sm8550-dispcc";
+ reg = <0 0x0af00000 0 0x20000>;
+ clocks = <&bi_tcxo_div2>,
+ <&bi_tcxo_ao_div2>,
+ <&gcc GCC_DISP_AHB_CLK>,
+ <&sleep_clk>,
+ <&mdss_dsi0_phy 0>,
+ <&mdss_dsi0_phy 1>,
+ <&mdss_dsi1_phy 0>,
+ <&mdss_dsi1_phy 1>,
+ <0>, /* dp0 */
+ <0>,
+ <0>, /* dp1 */
+ <0>,
+ <0>, /* dp2 */
+ <0>,
+ <0>, /* dp3 */
+ <0>;
+ power-domains = <&rpmhpd SM8550_MMCX>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ status = "disabled";
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sm8550-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;
--
2.34.1
