On 2022/12/29 3:50, Conor Dooley wrote:
> Hey Walker,
> Took another bit of a look.
Hey Conor, sorry for delay respond as I was busy with other things.
>
> On Wed, Dec 28, 2022 at 10:08:55AM +0800, Walker Chen wrote:
>> On 2022/12/20 4:40, Conor Dooley wrote:
>> > Hey Walker,
>> >
>> > Hopefully just some minor bits here. Hopefully either Emil who has a
>> > board, or someone that knows power management stuff better can give this
>> > a proper review.
>> >
>> > On Thu, Dec 08, 2022 at 04:45:22PM +0800, Walker Chen wrote:
>> >> Add pmu driver for the StarFive JH71XX SoC.
>> >>
>> >> As the power domains provider, the Power Management Unit (PMU) is
>> >> designed for including multiple PM domains that can be used for power
>> >> gating of selected IP blocks for power saving by reduced leakage
>> >> current. It accepts software encourage command to switch the power mode
>> >> of SoC.
>> >>
>> >> Signed-off-by: Walker Chen <walker.chen@xxxxxxxxxxxxxxxx>
>> >> ---
>> >> MAINTAINERS | 14 ++
>> >> drivers/soc/Kconfig | 1 +
>> >> drivers/soc/Makefile | 1 +
>> >> drivers/soc/starfive/Kconfig | 11 +
>> >> drivers/soc/starfive/Makefile | 3 +
>> >> drivers/soc/starfive/jh71xx_pmu.c | 396 ++++++++++++++++++++++++++++++
>> >> 6 files changed, 426 insertions(+)
>> >> create mode 100644 drivers/soc/starfive/Kconfig
>> >> create mode 100644 drivers/soc/starfive/Makefile
>> >> create mode 100644 drivers/soc/starfive/jh71xx_pmu.c
>> >>
>> >
>> >> +config JH71XX_PMU
>> >> + bool "Support PMU for StarFive JH71XX Soc"
>> >> + depends on PM && (SOC_STARFIVE || COMPILE_TEST)
>> >
>> > Why not just do:
>> > depends on PM
>> > depends on SOC_STARFIVE || COMPILE_TEST
>> > I think that way reads a little better.
>>
>> No problem, will be changed like this way.
>>
>> >
>> >> + default SOC_STARFIVE
>> >> + select PM_GENERIC_DOMAINS
>> >> + help
>> >> + Say 'y' here to enable support power domain support.
>> >> + In order to meet low power requirements, a Power Management Unit (PMU)
>> >> + is designed for controlling power resources in StarFive JH71XX SoCs.
>> >> diff --git a/drivers/soc/starfive/Makefile b/drivers/soc/starfive/Makefile
>> >> new file mode 100644
>> >> index 000000000000..13b589d6b5f3
>> >> --- /dev/null
>> >> +++ b/drivers/soc/starfive/Makefile
>> >> @@ -0,0 +1,3 @@
>> >> +# SPDX-License-Identifier: GPL-2.0
>> >> +
>> >> +obj-$(CONFIG_JH71XX_PMU) += jh71xx_pmu.o
>> >> diff --git a/drivers/soc/starfive/jh71xx_pmu.c b/drivers/soc/starfive/jh71xx_pmu.c
>> >> new file mode 100644
>> >> index 000000000000..7a0145779e07
>> >> --- /dev/null
>> >> +++ b/drivers/soc/starfive/jh71xx_pmu.c
>> >> @@ -0,0 +1,396 @@
>> >> +// SPDX-License-Identifier: GPL-2.0-or-later
>> >> +/*
>> >> + * StarFive JH71XX PMU (Power Management Unit) Controller Driver
>> >> + *
>> >> + * Copyright (C) 2022 StarFive Technology Co., Ltd.
>> >> + */
>> >> +
>> >> +#include <linux/interrupt.h>
>> >> +#include <linux/io.h>
>> >> +#include <linux/iopoll.h>
>> >> +#include <linux/module.h>
>> >> +#include <linux/of.h>
>> >> +#include <linux/of_device.h>
>> >> +#include <linux/platform_device.h>
>> >> +#include <linux/pm_domain.h>
>> >> +#include <dt-bindings/power/starfive,jh7110-pmu.h>
>> >> +
>> >> +/* register offset */
>> >> +#define JH71XX_PMU_HW_EVENT_ON 0x04
>> >> +#define JH71XX_PMU_HW_EVENT_OFF 0x08
>
> Neither of these are used here at the moment - would they be used in the
> future? Also the docs fail to describe this PMU_HW_EVENT_OFF register,
> although the HW_ON, and SW_FOO ones are described.
They are not used in the current version, may be used in the future with the improvement of driver.
If so, how about your suggestion ? drop them ?
>
>> >> +#define JH71XX_PMU_SW_TURN_ON_POWER 0x0C
>> >> +#define JH71XX_PMU_SW_TURN_OFF_POWER 0x10
>> >> +#define JH71XX_PMU_SW_ENCOURAGE 0x44
>> >> +#define JH71XX_PMU_INT_MASK 0x48
>
> This one is called the "Timer Interrupt Mask", so we may as well match
> that naming here, no?
OK, will be changed.
>
>> >> +#define JH71XX_PMU_PCH_BYPASS 0x4C
>> >> +#define JH71XX_PMU_PCH_PSTATE 0x50
>> >> +#define JH71XX_PMU_PCH_TIMEOUT 0x54
>> >> +#define JH71XX_PMU_LP_TIMEOUT 0x58
>> >> +#define JH71XX_PMU_HW_TURN_ON 0x5C
>
> Same here, this HW related bit is also not used AFAICT.
> Do you intend adding a user of the HW encourage at some point in the
> future?
I haven't thought about this yet. At least SW encourage can work now.
>
>> >> +#define JH71XX_PMU_CURR_POWER_MODE 0x80
>> >> +#define JH71XX_PMU_EVENT_STATUS 0x88
>> >> +#define JH71XX_PMU_INT_STATUS 0x8C
>> >> +
>> >> +/* sw encourage cfg */
>> >> +#define JH71XX_PMU_SW_ENCOURAGE_EN_LO 0x05
>> >> +#define JH71XX_PMU_SW_ENCOURAGE_EN_HI 0x50
>> >> +#define JH71XX_PMU_SW_ENCOURAGE_DIS_LO 0x0A
>> >> +#define JH71XX_PMU_SW_ENCOURAGE_DIS_HI 0xA0
>> >> +#define JH71XX_PMU_SW_ENCOURAGE_ON 0xFF
>
> This all seems to correspond w/ docs...
>
>> >> +
>> >> +/* pmu int status */
>> >> +#define JH71XX_PMU_INT_SEQ_DONE BIT(0)
>> >> +#define JH71XX_PMU_INT_HW_REQ BIT(1)
>> >> +#define JH71XX_PMU_INT_SW_FAIL GENMASK(3, 2)
>> >> +#define JH71XX_PMU_INT_HW_FAIL GENMASK(5, 4)
>> >> +#define JH71XX_PMU_INT_PCH_FAIL GENMASK(8, 6)
>> >> +#define JH71XX_PMU_INT_FAIL_MASK (JH71XX_PMU_INT_SW_FAIL | \
>> >> + JH71XX_PMU_INT_HW_FAIL | \
>> >> + JH71XX_PMU_INT_PCH_FAIL)
>> >> +#define JH71XX_PMU_INT_ALL_MASK (JH71XX_PMU_INT_SEQ_DONE | \
>> >> + JH71XX_PMU_INT_HW_REQ | \
>> >> + JH71XX_PMU_INT_FAIL_MASK)
>
> ...as does all of this - although, could the FAIL_MASK be dropped as it
> appears to only be used here & the ALL_MASK definition be replaced with
> GENMASK(8, 0)?
> I don't really mind what you do here, think it just may be slightly
> easier to read, so if you disagree leave it as is.
Maybe your way is more readable.
>
>> >> +
>> >> +/*
>> >> + * The time required for switching power status is based on the time
>> >> + * to turn on the largest domain's power, which is at microsecond level
>
> Would you mind mentioning which domain that is?
> USB seems to be listed in Table 3-9 as 200 us.
Hardware colleague told me this time is based on the time to turn on the largest
domain's power, but he didn't tell me which one it was. This time refers to the
time required for switching the status of power domains, is not the time of power-up for analog PHY.
USB is not one of power domains in JH7110 SoC.
>
>> >> + */
>> >> +#define JH71XX_PMU_TIMEOUT_US 100
>
> I'm happy enough with things, apart from my lack of familiarity with the
> power management APIs. Perhaps when you send the next version, someone
> else can comment there.
Anyway, I appreciate your detailed reading and comments.
>
>> >> +struct jh71xx_domain_info {
>> >
>> > const char * const name;
>> > unsigned int flags;
>> > u8 bit;
>> >
>> >> +};
>> >> +
>> >> +struct jh71xx_pmu_match_data {
>> >
>> > const struct jh71xx_domain_info *domain_info;
>> > int num_domains;
>> >
>> > Can you switch these two around like so?
>>
>> Should be no problem.
>>
>> >> +};
>> >> +
>> >> +struct jh71xx_pmu {
>> >> + struct device *dev;
>> >> + const struct jh71xx_pmu_match_data *match_data;
>> >> + void __iomem *base;
>> >> + spinlock_t lock; /* protects pmu reg */
>> >> + int irq;
>> >> + struct genpd_onecell_data genpd_data;
>> >> + struct generic_pm_domain **genpd;
>> >> +};
>> >> +
>> >> +struct jh71xx_pmu_dev {
>> >> + struct generic_pm_domain genpd;
>> >> + const struct jh71xx_domain_info *domain_info;
>> >> + struct jh71xx_pmu *pmu;
>> >
>> > And these two too please in the same way.
>>
>> Nice :)
>>
>> >
>> >> +};
>> >> +
>> >> +static int jh71xx_pmu_get_state(struct jh71xx_pmu_dev *pmd, u32 mask, bool *is_on)
>> >> +{
>> >> + struct jh71xx_pmu *pmu = pmd->pmu;
>> >> +
>> >> + if (!mask) {
>> >> + *is_on = false;
>> >> + return -EINVAL;
>> >> + }
>> >> +
>> >> + *is_on = readl(pmu->base + JH71XX_PMU_CURR_POWER_MODE) & mask;
>> >> +
>> >> + return 0;
>> >> +}
>> >> +
>> >> +static int jh71xx_pmu_set_state(struct jh71xx_pmu_dev *pmd, u32 mask, bool on)
>> >> +{
>> >> + struct jh71xx_pmu *pmu = pmd->pmu;
>> >> + unsigned long flags;
>> >> + u32 val;
>> >> + u32 mode;
>> >> + u32 encourage_lo;
>> >> + u32 encourage_hi;
>> >> + bool is_on;
>> >> + int ret;
>> >> +
>> >> + ret = jh71xx_pmu_get_state(pmd, mask, &is_on);
>> >> + if (ret) {
>> >> + dev_dbg(pmu->dev, "unable to get current state for %s\n",
>> >> + pmd->genpd.name);
>> >> + return ret;
>> >> + }
>> >> +
>> >> + if (is_on == on) {
>> >> + dev_dbg(pmu->dev, "pm domain [%s] is already %sable status.\n",
>> >> + pmd->genpd.name, on ? "en" : "dis");
>> >> + return 0;
>> >> + }
>> >> +
>> >> + spin_lock_irqsave(&pmu->lock, flags);
>> >> +
>> >> + /*
>> >> + * The PMU accepts software encourage to switch power mode in the following 2 steps:
>> >> + *
>> >> + * 1. Configure the register SW_TURN_ON_POWER (offset 0x0c), write 1 to
>> >> + * the bit which power domain will be turn-on, write 0 to the others.
>> >
>> > Some grammatical nit picking..
>> >
>> > "Configure the register blah (offset 0x0c) by writing 1 to the bit
>> > corresponding to the power domain that will be turned on and writing
>> > zero to the others."
>> >
>> > Is that a correct correct summation of the operation?
>>
>> Yes, maybe your description is better easy-to-understand.
>>
>> >
>> >> + * Likewise, configure the register SW_TURN_OFF_POWER (offset 0x10),
>> >> + * write 1 to the bit which power domain will be turn-off, write 0 to the others.
>> >
>> >
>> >> + */
>> >> + if (on) {
>> >> + mode = JH71XX_PMU_SW_TURN_ON_POWER;
>> >> + encourage_lo = JH71XX_PMU_SW_ENCOURAGE_EN_LO;
>> >> + encourage_hi = JH71XX_PMU_SW_ENCOURAGE_EN_HI;
>> >> + } else {
>> >> + mode = JH71XX_PMU_SW_TURN_OFF_POWER;
>> >> + encourage_lo = JH71XX_PMU_SW_ENCOURAGE_DIS_LO;
>> >> + encourage_hi = JH71XX_PMU_SW_ENCOURAGE_DIS_HI;
>> >> + }
>> >> +
>> >> + writel(mask, pmu->base + mode);
>> >> +
>> >> + /*
>> >> + * 2. Write SW encourage command sequence to the Software Encourage Reg (offset 0x44)
>> >> + * SW turn-on command sequence: 0xff -> 0x05 -> 0x50
>> >> + * SW turn-off command sequence: 0xff -> 0x0a -> 0xa0
>> >
>> > I think you could replace the hard "coded" numbers here with a better
>> > description idk without looking at the #defines above what these
>> > correspond to. AFAICT, it'd be something like:
>> > First write the ...ENCOURAGE_ON to reset the state machine which parses
>> > the command sequence. It must be written every time.
>> > Then write the lower bits of the command sequence, followed by the upper
>> > bits. The sequence differs between powering on & off a domain.
>>
>> Thank you for correction for these description. Because English is not my native language,
>> so not very good in some sentences. I'll take your advice.
>
> It may be mine but that does not mean I don't make mistakes either :)
> In this case, I'd like to re-word my suggestion. How about:
> First write ...ENCOURAGE_ON to ...SW_ENCOURAGE. This will reset the state
> machine which parses the command sequence. This register must be written
> every time software wants to power on/off a domain.
> Then write the lower bits of the command sequence, followed by the upper
> bits. The sequence differs between powering on & off a domain.
>
> When I read my previous suggestion back, I had to read it more than once
> to get what I had meant...
In brief, the key is to clearly describe the software steps and it's easy to understand.
>
>> >> + * Note: writing SW_MODE_ENCOURAGE_ON (0xFF) to the SW_ENCOURAGE register,
>> >> + * the purpose is to reset the state machine which is going to parse instruction
>> >> + * sequence. It has to be written every time.
>> >> + */
>> >> + writel(JH71XX_PMU_SW_ENCOURAGE_ON, pmu->base + JH71XX_PMU_SW_ENCOURAGE);
>> >> + writel(encourage_lo, pmu->base + JH71XX_PMU_SW_ENCOURAGE);
>> >> + writel(encourage_hi, pmu->base + JH71XX_PMU_SW_ENCOURAGE);
>> >> +
>> >> + spin_unlock_irqrestore(&pmu->lock, flags);
>> >> +
>> >> + /* Wait for the power domain bit to be enabled / disabled */
>> >> + if (on) {
>> >> + ret = readl_poll_timeout_atomic(pmu->base + JH71XX_PMU_CURR_POWER_MODE,
>> >> + val, val & mask,
>> >> + 1, JH71XX_PMU_TIMEOUT_US);
>> >> + } else {
>> >> + ret = readl_poll_timeout_atomic(pmu->base + JH71XX_PMU_CURR_POWER_MODE,
>> >> + val, !(val & mask),
>> >> + 1, JH71XX_PMU_TIMEOUT_US);
>> >> + }
>> >> +
>> >> + if (ret) {
>> >> + dev_err(pmu->dev, "%s: failed to power %s\n",
>> >> + pmd->genpd.name, on ? "on" : "off");
>> >> + return -ETIMEDOUT;
>> >> + }
>> >> +
>> >> + return 0;
>> >> +}
>> >
>> >> +static int jh71xx_pmu_probe(struct platform_device *pdev)
>> >> +{
>> >> + struct device *dev = &pdev->dev;
>> >> + struct device_node *np = dev->of_node;
>> >> + const struct jh71xx_pmu_match_data *match_data;
>> >> + struct jh71xx_pmu *pmu;
>> >> + unsigned int i;
>> >> + int ret;
>> >> +
>> >> + pmu = devm_kzalloc(dev, sizeof(*pmu), GFP_KERNEL);
>> >> + if (!pmu)
>> >> + return -ENOMEM;
>> >> +
>> >> + pmu->base = devm_platform_ioremap_resource(pdev, 0);
>> >> + if (IS_ERR(pmu->base))
>> >> + return PTR_ERR(pmu->base);
>> >> +
>> >> + /* initialize pmu interrupt */
>> >
>> > nit: this comment is ~pointless.
>>
>> Will be dropped.
>>
>> >
>> >> + pmu->irq = platform_get_irq(pdev, 0);
>> >> + if (pmu->irq < 0)
>> >> + return pmu->irq;
>> >> +
>> >> + ret = devm_request_irq(dev, pmu->irq, jh71xx_pmu_interrupt,
>> >> + 0, pdev->name, pmu);
>> >> + if (ret)
>> >> + dev_err(dev, "request irq failed.\n");
>> >
>> > nit: s/request/requesting
>>
>> Will be fixed.
>>
>> >
>> > Unfortunately I cannot really review the rest of this, but hopefully
>> > I'll get a board soon and can try it out - or else send me a link to
>> > your TRM or w/e.
>>
>> Anyway, I would like to thank you very much for your time.
>
> Oh, while I think of it - I was talking to some people from Imagination
> at the RISC-V Summit who said they're working on open sourcing their
> GPU drivers, so hopefully we do end up with an open source driver for
> the one on JH7110 soon :)
Of course, hopefully the GPU can also be open source eventually.
Best regards,
Walker Chen
