Add dts support for yt8521 and yt8531s. This patch has
been tested on AM335x platform which has one YT8531S interface
card and passed all test cases.
Signed-off-by: Frank <Frank.Sae@xxxxxxxxxxxxxx>
---
drivers/net/phy/motorcomm.c | 517 ++++++++++++++++++++++++++++++------
1 file changed, 434 insertions(+), 83 deletions(-)
diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index 685190db72de..7ebcca374a67 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -10,10 +10,11 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
+#include <linux/of.h>
#define PHY_ID_YT8511 0x0000010a
-#define PHY_ID_YT8521 0x0000011A
-#define PHY_ID_YT8531S 0x4F51E91A
+#define PHY_ID_YT8521 0x0000011a
+#define PHY_ID_YT8531S 0x4f51e91a
/* YT8521/YT8531S Register Overview
* UTP Register space | FIBER Register space
@@ -144,6 +145,16 @@
#define YT8521_ESC1R_SLEEP_SW BIT(15)
#define YT8521_ESC1R_PLLON_SLP BIT(14)
+/* Phy Serdes analog cfg2 Register */
+#define YTPHY_SERDES_ANALOG_CFG2_REG 0xA1
+#define YTPHY_SAC2R_TX_AMPLITUDE_MASK ((0x7 << 13) | (0x7 << 1))
+#define YT8521_SAC2R_TX_AMPLITUDE_LOW ((0x7 << 13) | (0x0 << 1))
+#define YT8521_SAC2R_TX_AMPLITUDE_MIDDLE ((0x5 << 13) | (0x5 << 1))
+#define YT8521_SAC2R_TX_AMPLITUDE_HIGH ((0x3 << 13) | (0x6 << 1))
+#define YT8531S_SAC2R_TX_AMPLITUDE_LOW ((0x0 << 13) | (0x0 << 1))
+#define YT8531S_SAC2R_TX_AMPLITUDE_MIDDLE ((0x0 << 13) | (0x1 << 1))
+#define YT8531S_SAC2R_TX_AMPLITUDE_HIGH ((0x0 << 13) | (0x2 << 1))
+
/* Phy fiber Link timer cfg2 Register */
#define YT8521_LINK_TIMER_CFG2_REG 0xA5
#define YT8521_LTCR_EN_AUTOSEN BIT(15)
@@ -161,6 +172,7 @@
#define YT8521_CHIP_CONFIG_REG 0xA001
#define YT8521_CCR_SW_RST BIT(15)
+#define YT8521_CCR_RXC_DLY_EN BIT(8)
#define YT8521_CCR_MODE_SEL_MASK (BIT(2) | BIT(1) | BIT(0))
#define YT8521_CCR_MODE_UTP_TO_RGMII 0
@@ -178,22 +190,27 @@
#define YT8521_MODE_POLL 0x3
#define YT8521_RGMII_CONFIG1_REG 0xA003
-
+#define YT8521_RC1R_TX_CLK_SEL_MASK BIT(14)
+#define YT8521_RC1R_TX_CLK_SEL_ORIGINAL (0x0 << 14)
+#define YT8521_RC1R_TX_CLK_SEL_INVERTED (0x1 << 14)
/* TX Gig-E Delay is bits 3:0, default 0x1
* TX Fast-E Delay is bits 7:4, default 0xf
* RX Delay is bits 13:10, default 0x0
* Delay = 150ps * N
* On = 2250ps, off = 0ps
*/
-#define YT8521_RC1R_RX_DELAY_MASK (0xF << 10)
-#define YT8521_RC1R_RX_DELAY_EN (0xF << 10)
-#define YT8521_RC1R_RX_DELAY_DIS (0x0 << 10)
-#define YT8521_RC1R_FE_TX_DELAY_MASK (0xF << 4)
-#define YT8521_RC1R_FE_TX_DELAY_EN (0xF << 4)
-#define YT8521_RC1R_FE_TX_DELAY_DIS (0x0 << 4)
-#define YT8521_RC1R_GE_TX_DELAY_MASK (0xF << 0)
-#define YT8521_RC1R_GE_TX_DELAY_EN (0xF << 0)
-#define YT8521_RC1R_GE_TX_DELAY_DIS (0x0 << 0)
+#define YT8521_RC1R_GE_TX_DELAY_BIT (0)
+#define YT8521_RC1R_FE_TX_DELAY_BIT (4)
+#define YT8521_RC1R_RX_DELAY_BIT (10)
+#define YT8521_RC1R_RX_DELAY_MASK (0xF << YT8521_RC1R_RX_DELAY_BIT)
+#define YT8521_RC1R_RX_DELAY_EN (0xF << YT8521_RC1R_RX_DELAY_BIT)
+#define YT8521_RC1R_RX_DELAY_DIS (0x0 << YT8521_RC1R_RX_DELAY_BIT)
+#define YT8521_RC1R_FE_TX_DELAY_MASK (0xF << YT8521_RC1R_FE_TX_DELAY_BIT)
+#define YT8521_RC1R_FE_TX_DELAY_EN (0xF << YT8521_RC1R_FE_TX_DELAY_BIT)
+#define YT8521_RC1R_FE_TX_DELAY_DIS (0x0 << YT8521_RC1R_FE_TX_DELAY_BIT)
+#define YT8521_RC1R_GE_TX_DELAY_MASK (0xF << YT8521_RC1R_GE_TX_DELAY_BIT)
+#define YT8521_RC1R_GE_TX_DELAY_EN (0xF << YT8521_RC1R_GE_TX_DELAY_BIT)
+#define YT8521_RC1R_GE_TX_DELAY_DIS (0x0 << YT8521_RC1R_GE_TX_DELAY_BIT)
#define YTPHY_MISC_CONFIG_REG 0xA006
#define YTPHY_MCR_FIBER_SPEED_MASK BIT(0)
@@ -222,11 +239,33 @@
*/
#define YTPHY_WCR_TYPE_PULSE BIT(0)
-#define YT8531S_SYNCE_CFG_REG 0xA012
-#define YT8531S_SCR_SYNCE_ENABLE BIT(6)
+#define YTPHY_SYNCE_CFG_REG 0xA012
+#define YT8521_SCR_CLK_SRC_MASK (BIT(2) | BIT(1))
+#define YT8521_SCR_CLK_SRC_PLL_125M (0x0 << 1)
+#define YT8521_SCR_CLK_SRC_REF_25M (0x3 << 1)
+#define YT8521_SCR_SYNCE_ENABLE BIT(5)
+#define YT8521_SCR_CLK_FRE_SEL_MASK BIT(3)
+#define YT8521_SCR_CLK_FRE_SEL_125M (0x1 << 3)
+#define YT8521_SCR_CLK_FRE_SEL_25M (0x0 << 3)
+#define YT8531_SCR_CLK_SRC_MASK (BIT(3) | BIT(2) | BIT(1))
+#define YT8531_SCR_CLK_SRC_PLL_125M (0x0 << 1)
+#define YT8531_SCR_CLK_SRC_REF_25M (0x4 << 1)
+#define YT8531_SCR_SYNCE_ENABLE BIT(6)
+#define YT8531_SCR_CLK_FRE_SEL_MASK BIT(4)
+#define YT8531_SCR_CLK_FRE_SEL_125M (0x1 << 4)
+#define YT8531_SCR_CLK_FRE_SEL_25M (0x0 << 4)
/* Extended Register end */
+#define YTPHY_DTS_MAX_TX_AMPLITUDE 0x2
+#define YTPHY_DTS_MAX_DELAY_VAL 2250
+#define YTPHY_DTS_STEP_DELAY_VAL 150
+#define YTPHY_DTS_INVAL_VAL 0xFF
+
+#define YTPHY_DTS_OUTPUT_CLK_DIS 0
+#define YTPHY_DTS_OUTPUT_CLK_25M 25000000
+#define YTPHY_DTS_OUTPUT_CLK_125M 125000000
+
struct yt8521_priv {
/* combo_advertising is used for case of YT8521 in combo mode,
* this means that yt8521 may work in utp or fiber mode which depends
@@ -243,6 +282,30 @@ struct yt8521_priv {
* YT8521_RSSR_TO_BE_ARBITRATED
*/
u8 reg_page;
+
+ /* The following parameters are from dts */
+ /* rx delay = rx_delay_basic + rx_delay_additional
+ * basic delay is ~2ns, 0 = off, 1 = on
+ * rx_delay_additional,delay time = 150ps * val
+ */
+ u8 rx_delay_basic;
+ u8 rx_delay_additional;
+
+ /* tx_delay_ge is tx_delay for 1000Mbps
+ * tx_delay_fe is tx_delay for 100Mbps or 10Mbps
+ * delay time = 150ps * val
+ */
+ u8 tx_delay_ge;
+ u8 tx_delay_fe;
+ u8 sds_tx_amplitude;
+ bool keep_pll_enabled;
+ bool auto_sleep_disabled;
+ bool clock_ouput; /* output clock ctl: 0=off, 1=on */
+ bool clock_freq_125M; /* output clock freq selcect: 0=25M, 1=125M */
+ bool tx_clk_adj_enabled;/* tx clk adj ctl: 0=off, 1=on */
+ bool tx_clk_10_inverted;
+ bool tx_clk_100_inverted;
+ bool tx_clk_1000_inverted;
};
/**
@@ -593,6 +656,325 @@ static int yt8521_write_page(struct phy_device *phydev, int page)
return ytphy_modify_ext(phydev, YT8521_REG_SPACE_SELECT_REG, mask, set);
};
+static int ytphy_parse_dt(struct phy_device *phydev)
+{
+ struct device_node *node = phydev->mdio.dev.of_node;
+ struct yt8521_priv *priv = phydev->priv;
+ u32 freq, val;
+ int ret;
+
+ priv->rx_delay_additional = YTPHY_DTS_INVAL_VAL;
+ priv->sds_tx_amplitude = YTPHY_DTS_INVAL_VAL;
+ priv->rx_delay_basic = YTPHY_DTS_INVAL_VAL;
+ priv->tx_delay_ge = YTPHY_DTS_INVAL_VAL;
+ priv->tx_delay_fe = YTPHY_DTS_INVAL_VAL;
+
+ if (!IS_ENABLED(CONFIG_OF_MDIO)) {
+ priv->auto_sleep_disabled = true;
+ priv->keep_pll_enabled = true;
+ return 0;
+ }
+
+ ret = of_property_read_u32(node, "motorcomm,clk-out-frequency", &freq);
+ if (ret < 0)
+ freq = YTPHY_DTS_OUTPUT_CLK_DIS;/* default value as dts*/
+
+ switch (freq) {
+ case YTPHY_DTS_OUTPUT_CLK_DIS:
+ priv->clock_ouput = false;
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_25M:
+ priv->clock_freq_125M = false;
+ priv->clock_ouput = true;
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_125M:
+ priv->clock_freq_125M = true;
+ priv->clock_ouput = true;
+ break;
+ default:
+ phydev_err(phydev, "invalid motorcomm,clk-out-frequency\n");
+ return -EINVAL;
+ }
+
+ if (!of_property_read_u32(node, "motorcomm,rx-delay-basic", &val)) {
+ if (val > 1) {
+ phydev_err(phydev,
+ "invalid motorcomm,rx-delay-basic\n");
+ return -EINVAL;
+ }
+ priv->rx_delay_basic = val;
+ }
+
+ if (!of_property_read_u32(node, "motorcomm,rx-delay-additional-ps", &val)) {
+ if (val > YTPHY_DTS_MAX_DELAY_VAL) {
+ phydev_err(phydev, "invalid motorcomm,rx-delay-additional-ps\n");
+ return -EINVAL;
+ }
+ if (val)
+ val /= YTPHY_DTS_STEP_DELAY_VAL;
+ priv->rx_delay_additional = val;
+ }
+
+ if (!of_property_read_u32(node, "motorcomm,tx-delay-fe-ps", &val)) {
+ if (val > YTPHY_DTS_MAX_DELAY_VAL) {
+ phydev_err(phydev,
+ "invalid motorcomm,tx-delay-fe-ps\n");
+ return -EINVAL;
+ }
+ if (val)
+ val /= YTPHY_DTS_STEP_DELAY_VAL;
+ priv->tx_delay_fe = val;
+ }
+
+ if (!of_property_read_u32(node, "motorcomm,tx-delay-ge-ps", &val)) {
+ if (val > YTPHY_DTS_MAX_DELAY_VAL) {
+ phydev_err(phydev,
+ "invalid motorcomm,tx-delay-ge-ps\n");
+ return -EINVAL;
+ }
+ if (val)
+ val /= YTPHY_DTS_STEP_DELAY_VAL;
+ priv->tx_delay_ge = val;
+ }
+
+ if (of_property_read_bool(node, "motorcomm,keep-pll-enabled"))
+ priv->keep_pll_enabled = true;
+
+ if (of_property_read_bool(node, "motorcomm,auto-sleep-disabled"))
+ priv->auto_sleep_disabled = true;
+
+ if (of_property_read_bool(node, "motorcomm,tx-clk-adj-enabled"))
+ priv->tx_clk_adj_enabled = true;
+ if (priv->tx_clk_adj_enabled) {
+ if (of_property_read_bool(node, "motorcomm,tx-clk-10-inverted"))
+ priv->tx_clk_10_inverted = true;
+ if (of_property_read_bool(node, "motorcomm,tx-clk-100-inverted"))
+ priv->tx_clk_100_inverted = true;
+ if (of_property_read_bool(node, "motorcomm,tx-clk-1000-inverted"))
+ priv->tx_clk_1000_inverted = true;
+ }
+
+ if (!of_property_read_u32(node, "motorcomm,sds-tx-amplitude", &val)) {
+ if (val > YTPHY_DTS_MAX_TX_AMPLITUDE) {
+ phydev_err(phydev,
+ "invalid motorcomm,sds-tx-amplitude\n");
+ return -EINVAL;
+ }
+ priv->sds_tx_amplitude = val;
+ }
+
+ return 0;
+}
+
+static int ytphy_clk_out_config(struct phy_device *phydev)
+{
+ struct yt8521_priv *priv = phydev->priv;
+ u16 set = 0;
+ u16 mask;
+
+ switch (phydev->drv->phy_id) {
+ case PHY_ID_YT8511:
+ /* YT8511 will be supported later */
+ return -EOPNOTSUPP;
+ case PHY_ID_YT8521:
+ mask = YT8521_SCR_SYNCE_ENABLE;
+ if (priv->clock_ouput) {
+ mask |= YT8521_SCR_CLK_SRC_MASK;
+ mask |= YT8521_SCR_CLK_FRE_SEL_MASK;
+ set |= YT8521_SCR_SYNCE_ENABLE;
+ if (priv->clock_freq_125M) {
+ set |= YT8521_SCR_CLK_FRE_SEL_125M;
+ set |= YT8521_SCR_CLK_SRC_PLL_125M;
+ } else {
+ set |= YT8521_SCR_CLK_FRE_SEL_25M;
+ set |= YT8521_SCR_CLK_SRC_REF_25M;
+ }
+ }
+ break;
+ case PHY_ID_YT8531:
+ case PHY_ID_YT8531S:
+ mask = YT8531_SCR_SYNCE_ENABLE;
+ if (priv->clock_ouput) {
+ mask |= YT8531_SCR_CLK_SRC_MASK;
+ mask |= YT8531_SCR_CLK_FRE_SEL_MASK;
+ set |= YT8531_SCR_SYNCE_ENABLE;
+ if (priv->clock_freq_125M) {
+ set |= YT8531_SCR_CLK_FRE_SEL_125M;
+ set |= YT8531_SCR_CLK_SRC_PLL_125M;
+ } else {
+ set |= YT8531_SCR_CLK_FRE_SEL_25M;
+ set |= YT8531_SCR_CLK_SRC_REF_25M;
+ }
+ }
+ break;
+ default:
+ phydev_err(phydev, "invalid phy id\n");
+ return -EINVAL;
+ }
+
+ return ytphy_modify_ext(phydev, YTPHY_SYNCE_CFG_REG, mask, set);
+}
+
+static int ytphy_serdes_tx_amplitude_config(struct phy_device *phydev)
+{
+ u16 yt8531s_tx_amplitude[] = { YT8531S_SAC2R_TX_AMPLITUDE_LOW,
+ YT8531S_SAC2R_TX_AMPLITUDE_MIDDLE,
+ YT8531S_SAC2R_TX_AMPLITUDE_HIGH };
+ u16 yt8521_tx_amplitude[] = { YT8521_SAC2R_TX_AMPLITUDE_LOW,
+ YT8521_SAC2R_TX_AMPLITUDE_MIDDLE,
+ YT8521_SAC2R_TX_AMPLITUDE_HIGH };
+ struct yt8521_priv *priv = phydev->priv;
+ u16 tx_amplitude;
+
+ if (priv->sds_tx_amplitude == YTPHY_DTS_INVAL_VAL)
+ /* don't config Serdes tx amplitude.*/
+ return 0;
+
+ switch (phydev->drv->phy_id) {
+ case PHY_ID_YT8511:
+ case PHY_ID_YT8531:
+ /* YT8511 and YT8531 not support this function.*/
+ return -EOPNOTSUPP;
+ case PHY_ID_YT8521:
+ tx_amplitude = yt8521_tx_amplitude[priv->sds_tx_amplitude];
+ break;
+ case PHY_ID_YT8531S:
+ tx_amplitude = yt8531s_tx_amplitude[priv->sds_tx_amplitude];
+ break;
+ default:
+ phydev_err(phydev, "invalid phy id\n");
+ return -EINVAL;
+ }
+
+ return ytphy_modify_ext(phydev, YTPHY_SERDES_ANALOG_CFG2_REG,
+ YTPHY_SAC2R_TX_AMPLITUDE_MASK, tx_amplitude);
+}
+
+static int ytphy_rgmii_clk_delay_config(struct phy_device *phydev)
+{
+ struct yt8521_priv *priv = phydev->priv;
+ u16 mask = 0;
+ u16 val = 0;
+ int ret;
+
+ /* rx delay basic controlled by dts.*/
+ if (priv->rx_delay_basic != YTPHY_DTS_INVAL_VAL) {
+ if (priv->rx_delay_basic)
+ val = YT8521_CCR_RXC_DLY_EN;
+ ret = ytphy_modify_ext(phydev, YT8521_CHIP_CONFIG_REG,
+ YT8521_CCR_RXC_DLY_EN, val);
+ if (ret < 0)
+ return ret;
+ }
+
+ val = 0;
+ /* If rx_delay_additional and tx_delay_* are all not be seted in dts,
+ * then used the fixed *_DELAY_DIS or *_DELAY_EN. Otherwise, use the
+ * value set by rx_delay_additional, tx_delay_ge and tx_delay_fe.
+ */
+ if ((priv->rx_delay_additional & priv->tx_delay_ge & priv->tx_delay_fe)
+ == YTPHY_DTS_INVAL_VAL) {
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ val |= YT8521_RC1R_GE_TX_DELAY_DIS;
+ val |= YT8521_RC1R_FE_TX_DELAY_DIS;
+ val |= YT8521_RC1R_RX_DELAY_DIS;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ val |= YT8521_RC1R_GE_TX_DELAY_DIS;
+ val |= YT8521_RC1R_FE_TX_DELAY_DIS;
+ val |= YT8521_RC1R_RX_DELAY_EN;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ val |= YT8521_RC1R_GE_TX_DELAY_EN;
+ val |= YT8521_RC1R_FE_TX_DELAY_EN;
+ val |= YT8521_RC1R_RX_DELAY_DIS;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ val |= YT8521_RC1R_GE_TX_DELAY_EN;
+ val |= YT8521_RC1R_FE_TX_DELAY_EN;
+ val |= YT8521_RC1R_RX_DELAY_EN;
+ break;
+ default: /* do not support other modes */
+ return -EOPNOTSUPP;
+ }
+ mask = YT8521_RC1R_RX_DELAY_MASK | YT8521_RC1R_FE_TX_DELAY_MASK
+ | YT8521_RC1R_GE_TX_DELAY_MASK;
+ } else {
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ if (priv->rx_delay_additional != YTPHY_DTS_INVAL_VAL) {
+ mask |= YT8521_RC1R_RX_DELAY_MASK;
+ val |= (priv->rx_delay_additional) << YT8521_RC1R_RX_DELAY_BIT;
+ }
+ if (priv->tx_delay_fe != YTPHY_DTS_INVAL_VAL) {
+ mask |= YT8521_RC1R_FE_TX_DELAY_MASK;
+ val |= (priv->tx_delay_fe) << YT8521_RC1R_FE_TX_DELAY_BIT;
+ }
+ if (priv->tx_delay_ge != YTPHY_DTS_INVAL_VAL) {
+ mask |= YT8521_RC1R_GE_TX_DELAY_MASK;
+ val |= (priv->tx_delay_ge) << YT8521_RC1R_GE_TX_DELAY_BIT;
+ }
+ break;
+ default: /* do not support other modes */
+ return -EOPNOTSUPP;
+ }
+ }
+
+ return ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG, mask, val);
+}
+
+static int ytphy_clk_delay_config(struct phy_device *phydev)
+{
+ switch (phydev->drv->phy_id) {
+ case PHY_ID_YT8511:
+ /* YT8511 will be supported later */
+ return -EOPNOTSUPP;
+ case PHY_ID_YT8521:
+ case PHY_ID_YT8531S:
+ /* YT8521 and YT8531S support SGMII mode, but don't need
+ * delay.
+ */
+ if (phydev->interface == PHY_INTERFACE_MODE_SGMII)
+ return 0;
+
+ return ytphy_rgmii_clk_delay_config(phydev);
+ case PHY_ID_YT8531:
+ /* YT8531 don't support SGMII mode. */
+ return ytphy_rgmii_clk_delay_config(phydev);
+ default:
+ phydev_err(phydev, "invalid phy id\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int ytphy_probe_helper(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct yt8521_priv *priv;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ phydev->priv = priv;
+
+ ret = ytphy_parse_dt(phydev);
+ if (ret < 0)
+ return ret;
+
+ phy_lock_mdio_bus(phydev);
+ ret = ytphy_clk_out_config(phydev);
+ phy_unlock_mdio_bus(phydev);
+ return ret;
+}
+
/**
* yt8521_probe() - read chip config then set suitable polling_mode
* @phydev: a pointer to a &struct phy_device
@@ -601,16 +983,15 @@ static int yt8521_write_page(struct phy_device *phydev, int page)
*/
static int yt8521_probe(struct phy_device *phydev)
{
- struct device *dev = &phydev->mdio.dev;
struct yt8521_priv *priv;
int chip_config;
int ret;
- priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
- if (!priv)
- return -ENOMEM;
+ ret = ytphy_probe_helper(phydev);
+ if (ret < 0)
+ return ret;
- phydev->priv = priv;
+ priv = phydev->priv;
chip_config = ytphy_read_ext_with_lock(phydev, YT8521_CHIP_CONFIG_REG);
if (chip_config < 0)
@@ -651,26 +1032,6 @@ static int yt8521_probe(struct phy_device *phydev)
return 0;
}
-/**
- * yt8531s_probe() - read chip config then set suitable polling_mode
- * @phydev: a pointer to a &struct phy_device
- *
- * returns 0 or negative errno code
- */
-static int yt8531s_probe(struct phy_device *phydev)
-{
- int ret;
-
- /* Disable SyncE clock output by default */
- ret = ytphy_modify_ext_with_lock(phydev, YT8531S_SYNCE_CFG_REG,
- YT8531S_SCR_SYNCE_ENABLE, 0);
- if (ret < 0)
- return ret;
-
- /* same as yt8521_probe */
- return yt8521_probe(phydev);
-}
-
/**
* ytphy_utp_read_lpa() - read LPA then setup lp_advertising for utp
* @phydev: a pointer to a &struct phy_device
@@ -1125,6 +1486,34 @@ static int yt8521_resume(struct phy_device *phydev)
return yt8521_modify_utp_fiber_bmcr(phydev, BMCR_PDOWN, 0);
}
+static int ytphy_config_init_helper(struct phy_device *phydev)
+{
+ struct yt8521_priv *priv = phydev->priv;
+ int ret;
+
+ ret = ytphy_clk_delay_config(phydev);
+ if (ret < 0)
+ return ret;
+
+ /* disable auto sleep */
+ if (priv->auto_sleep_disabled) {
+ ret = ytphy_modify_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1_REG,
+ YT8521_ESC1R_SLEEP_SW, 0);
+ if (ret < 0)
+ return ret;
+ }
+
+ /* enable RXC clock when no wire plug */
+ if (priv->keep_pll_enabled) {
+ ret = ytphy_modify_ext(phydev, YT8521_CLOCK_GATING_REG,
+ YT8521_CGR_RX_CLK_EN, 0);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
/**
* yt8521_config_init() - called to initialize the PHY
* @phydev: a pointer to a &struct phy_device
@@ -1135,59 +1524,21 @@ static int yt8521_config_init(struct phy_device *phydev)
{
int old_page;
int ret = 0;
- u16 val;
old_page = phy_select_page(phydev, YT8521_RSSR_UTP_SPACE);
if (old_page < 0)
goto err_restore_page;
- switch (phydev->interface) {
- case PHY_INTERFACE_MODE_RGMII:
- val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_FE_TX_DELAY_DIS;
- val |= YT8521_RC1R_RX_DELAY_DIS;
- break;
- case PHY_INTERFACE_MODE_RGMII_RXID:
- val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_FE_TX_DELAY_DIS;
- val |= YT8521_RC1R_RX_DELAY_EN;
- break;
- case PHY_INTERFACE_MODE_RGMII_TXID:
- val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_FE_TX_DELAY_EN;
- val |= YT8521_RC1R_RX_DELAY_DIS;
- break;
- case PHY_INTERFACE_MODE_RGMII_ID:
- val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_FE_TX_DELAY_EN;
- val |= YT8521_RC1R_RX_DELAY_EN;
- break;
- case PHY_INTERFACE_MODE_SGMII:
- break;
- default: /* do not support other modes */
- ret = -EOPNOTSUPP;
- goto err_restore_page;
- }
-
- /* set rgmii delay mode */
- if (phydev->interface != PHY_INTERFACE_MODE_SGMII) {
- ret = ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG,
- (YT8521_RC1R_RX_DELAY_MASK |
- YT8521_RC1R_FE_TX_DELAY_MASK |
- YT8521_RC1R_GE_TX_DELAY_MASK),
- val);
- if (ret < 0)
- goto err_restore_page;
- }
-
- /* disable auto sleep */
- ret = ytphy_modify_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1_REG,
- YT8521_ESC1R_SLEEP_SW, 0);
+ ret = ytphy_config_init_helper(phydev);
if (ret < 0)
goto err_restore_page;
- /* enable RXC clock when no wire plug */
- ret = ytphy_modify_ext(phydev, YT8521_CLOCK_GATING_REG,
- YT8521_CGR_RX_CLK_EN, 0);
+ ret = yt8521_write_page(phydev, YT8521_RSSR_FIBER_SPACE);
if (ret < 0)
goto err_restore_page;
+ ret = ytphy_serdes_tx_amplitude_config(phydev);
+
err_restore_page:
return phy_restore_page(phydev, old_page, ret);
}
@@ -1778,7 +2129,7 @@ static struct phy_driver motorcomm_phy_drvs[] = {
PHY_ID_MATCH_EXACT(PHY_ID_YT8531S),
.name = "YT8531S Gigabit Ethernet",
.get_features = yt8521_get_features,
- .probe = yt8531s_probe,
+ .probe = yt8521_probe,
.read_page = yt8521_read_page,
.write_page = yt8521_write_page,
.get_wol = ytphy_get_wol,
@@ -1804,7 +2155,7 @@ static const struct mdio_device_id __maybe_unused motorcomm_tbl[] = {
{ PHY_ID_MATCH_EXACT(PHY_ID_YT8511) },
{ PHY_ID_MATCH_EXACT(PHY_ID_YT8521) },
{ PHY_ID_MATCH_EXACT(PHY_ID_YT8531S) },
- { /* sentinal */ }
+ { /* sentinel */ }
};
MODULE_DEVICE_TABLE(mdio, motorcomm_tbl);
--
2.34.1
