Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the Yoshino devices DTs to better document the hardware and
rename already-defined GPIO nodes to fit the "official" names.
Note that 4k_ is replaced with four_k_ in one pin, as labels can't start
with numbers.
Lilac and Poplar have identical pin assignments.
Diff between these two and maple:
TLMM:
- "NC",
+ "TS_VDDIO_EN",
PMI8998:
- "NC"
+ "USB_SWITCH_SEL"
- "NC"
+ "4K_DISP_DCDC_EN"
PM8005:
- "NC"
+ "EAR_EN"
Which is probably due to Maple being designed and released quite a bit
earlier than the other two and it having a super high tech true-4K
display.
Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
---
.../msm8998-sony-xperia-yoshino-maple.dts | 179 +++++++++++-
.../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 260 +++++++++++++++---
2 files changed, 406 insertions(+), 33 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
index 20fe0394a3c1..e813b41f6db8 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
@@ -22,7 +22,7 @@ disp_dvdd_vreg: disp-dvdd-vreg {
enable-active-high;
gpio = <&pmi8998_gpio 10 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
- pinctrl-0 = <&disp_dvdd_en>;
+ pinctrl-0 = <&four_k_disp_dcdc_en>;
};
};
@@ -37,8 +37,30 @@ &lab {
qcom,soft-start-us = <200>;
};
+&pm8005_gpio {
+ gpio-line-names = "EAR_EN", /* GPIO_1 */
+ "NC",
+ "SLB",
+ "OPTION_1_PM8005";
+};
+
&pmi8998_gpio {
- disp_dvdd_en: disp-dvdd-en-active-state {
+ gpio-line-names = "MAIN_CAM_PWR_IO_EN", /* GPIO_1 */
+ "NC",
+ "NC",
+ "TYPEC_UUSB_SEL",
+ "VIB_LDO_EN",
+ "NC",
+ "DISPLAY_TYPE_SEL",
+ "USB_SWITCH_SEL",
+ "NC",
+ "4K_DISP_DCDC_EN", /* GPIO_10 */
+ "NC",
+ "DIV_CLK3",
+ "SPMI_I2C_SEL",
+ "NC";
+
+ four_k_disp_dcdc_en: 4k-disp-dcdc-en-state {
pins = "gpio10";
function = "normal";
bias-disable;
@@ -49,6 +71,159 @@ disp_dvdd_en: disp-dvdd-en-active-state {
};
};
+&tlmm {
+ gpio-line-names = "", /* GPIO_0 */
+ "",
+ "",
+ "",
+ "DEBUG_UART_TX",
+ "DEBUG_UART_RX",
+ "CAMSENSOR_I2C_SDA",
+ "CAMSENSOR_I2C_SCL",
+ "NC",
+ "NC",
+ "MDP_VSYNC_P", /* GPIO_10 */
+ "RGBC_IR_INT",
+ "NFC_VEN",
+ "CAM_MCLK0",
+ "CAM_MCLK1",
+ "NC",
+ "NC",
+ "CCI_I2C_SDA0",
+ "CCI_I2C_SCL0",
+ "CCI_I2C_SDA1",
+ "CCI_I2C_SCL1", /* GPIO_20 */
+ "MAIN_CAM_PWR_EN",
+ "TOF_INT_N",
+ "NC",
+ "NC",
+ "CHAT_CAM_PWR_EN",
+ "NC",
+ "TOF_RESET_N",
+ "CAM2_RSTN",
+ "NC",
+ "CAM1_RSTN", /* GPIO_30 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "CC_DIR",
+ "UIM2_DETECT_EN",
+ "FP_RESET_N", /* GPIO_40 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "BT_HCI_UART_TXD",
+ "BT_HCI_UART_RXD",
+ "BT_HCI_UART_CTS_N",
+ "BT_HCI_UART_RFR_N",
+ "NC",
+ "NC", /* GPIO_50 */
+ "NC",
+ "NC",
+ "CODEC_INT2_N",
+ "CODEC_INT1_N",
+ "APPS_I2C_SDA",
+ "APPS_I2C_SCL",
+ "FORCED_USB_BOOT",
+ "NC",
+ "NC",
+ "NC", /* GPIO_60 */
+ "NC",
+ "NC",
+ "TRAY2_DET_DS",
+ "CODEC_RST_N",
+ "WSA_L_EN",
+ "WSA_R_EN",
+ "NC",
+ "NC",
+ "NC",
+ "LPASS_SLIMBUS_CLK", /* GPIO_70 */
+ "LPASS_SLIMBUS_DATA0",
+ "LPASS_SLIMBUS_DATA1",
+ "BT_FM_SLIMBUS_DATA",
+ "BT_FM_SLIMBUS_CLK",
+ "NC",
+ "RF_LCD_ID_EN",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO_80 */
+ "SW_SERVICE",
+ "TX_GTR_THRES_IN",
+ "HW_ID0",
+ "HW_ID1",
+ "NC",
+ "NC",
+ "TS_I2C_SDA",
+ "TS_I2C_SCL",
+ "TS_RESET_N",
+ "NC", /* GPIO_90 */
+ "NC",
+ "NFC_IRQ",
+ "NFC_DWLD_EN",
+ "DISP_RESET_N",
+ "TRAY2_DET",
+ "CAM_SOF",
+ "RFFE6_CLK",
+ "RFFE6_DATA",
+ "DEBUG_GPIO0",
+ "DEBUG_GPIO1", /* GPIO_100 */
+ "GRFC4",
+ "NC",
+ "NC",
+ "RSVD",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RESET",
+ "UIM2_PRESENT",
+ "UIM1_DATA",
+ "UIM1_CLK", /* GPIO_110 */
+ "UIM1_RST",
+ "UIM1_PRESENT",
+ "UIM_BATT_ALARM",
+ "RSVD",
+ "NC",
+ "NC",
+ "ACCEL_INT",
+ "GYRO_INT",
+ "COMPASS_INT",
+ "ALS_PROX_INT_N", /* GPIO_120 */
+ "FP_INT_N",
+ "NC",
+ "BAROMETER_INT",
+ "ACC_COVER_OPEN",
+ "TS_INT_N",
+ "NC",
+ "NC",
+ "USB_DETECT_EN",
+ "NC",
+ "QLINK_REQUEST", /* GPIO_130 */
+ "QLINK_ENABLE",
+ "NC",
+ "TS_VDDIO_EN",
+ "WMSS_RESET_N",
+ "PA_INDICATOR_OR",
+ "NC",
+ "RFFE3_DATA",
+ "RFFE3_CLK",
+ "RFFE4_DATA",
+ "RFFE4_CLK", /* GPIO_140 */
+ "RFFE5_DATA",
+ "RFFE5_CLK",
+ "GNSS_EN",
+ "MSS_LTE_COXM_TXD",
+ "MSS_LTE_COXM_RXD",
+ "RFFE2_DATA",
+ "RFFE2_CLK",
+ "RFFE1_DATA",
+ "RFFE1_CLK";
+};
+
&vreg_l22a_2p85 {
regulator-min-microvolt = <2704000>;
regulator-max-microvolt = <2704000>;
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 5da87baa2b23..a083361a7bc4 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -21,7 +21,7 @@ / {
clocks {
div1_mclk: divclk1 {
compatible = "gpio-gate-clock";
- pinctrl-0 = <&audio_mclk_pin>;
+ pinctrl-0 = <&div_clk1>;
pinctrl-names = "default";
clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
#clock-cells = <0>;
@@ -46,7 +46,7 @@ cam0_vdig_vreg: cam0-vdig {
enable-active-high;
gpio = <&tlmm 21 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
- pinctrl-0 = <&cam0_vdig_default>;
+ pinctrl-0 = <&main_cam_pwr_en>;
};
cam1_vdig_vreg: cam1-vdig {
@@ -56,7 +56,7 @@ cam1_vdig_vreg: cam1-vdig {
enable-active-high;
gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
- pinctrl-0 = <&cam1_vdig_default>;
+ pinctrl-0 = <&chat_cam_pwr_en>;
vin-supply = <&vreg_s3a_1p35>;
};
@@ -67,7 +67,7 @@ cam_vio_vreg: cam-vio-vreg {
enable-active-high;
gpio = <&pmi8998_gpio 1 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
- pinctrl-0 = <&cam_vio_default>;
+ pinctrl-0 = <&main_cam_pwr_io_en>;
vin-supply = <&vreg_lvs1a_1p8>;
};
@@ -92,15 +92,14 @@ extcon_usb: extcon-usb {
id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>;
vbus-gpio = <&tlmm 128 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
- pinctrl-0 = <&usb_extcon_active &usb_vbus_active>;
+ pinctrl-0 = <&cc_dir_default &usb_detect_en>;
};
gpio-keys {
compatible = "gpio-keys";
label = "Side buttons";
pinctrl-names = "default";
- pinctrl-0 = <&vol_down_pin_a>, <&cam_focus_pin_a>,
- <&cam_snapshot_pin_a>;
+ pinctrl-0 = <&vol_down_n &focus_n &snapshot_n>;
button-vol-down {
label = "Volume Down";
gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
@@ -131,7 +130,7 @@ gpio-hall-sensor {
compatible = "gpio-keys";
label = "Hall sensors";
pinctrl-names = "default";
- pinctrl-0 = <&hall_sensor0_default>;
+ pinctrl-0 = <&acc_cover_open>;
event-hall-sensor0 {
label = "Cover Hall Sensor";
@@ -189,7 +188,7 @@ vibrator {
compatible = "gpio-vibrator";
enable-gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
- pinctrl-0 = <&vib_default>;
+ pinctrl-0 = <&vib_ldo_en>;
};
};
@@ -263,7 +262,7 @@ proximity@29 {
vdd-supply = <&cam_vio_vreg>;
pinctrl-names = "default";
- pinctrl-0 = <&tof_int &tof_reset>;
+ pinctrl-0 = <&tof_int_n &tof_reset>;
};
};
@@ -292,6 +291,13 @@ &lab {
regulator-soft-start;
};
+&pm8005_gpio {
+ gpio-line-names = "NC", /* GPIO_1 */
+ "NC",
+ "SLB",
+ "OPTION_1_PM8005";
+};
+
&pm8005_regulators {
/* VDD_GFX supply */
pm8005_s1: s1 {
@@ -304,7 +310,34 @@ pm8005_s1: s1 {
};
&pm8998_gpio {
- vol_down_pin_a: vol-down-active-state {
+ gpio-line-names = "UIM_BATT_ALARM", /* GPIO_1 */
+ "NC",
+ "WLAN_SW_CTRL (DISALLOWED)",
+ "SSC_PWR_EN",
+ "VOL_DOWN_N",
+ "VOL_UP_N",
+ "SNAPSHOT_N",
+ "FOCUS_N",
+ "FLASH_THERM",
+ "", /* GPIO_10 */
+ "",
+ "",
+ "DIV_CLK1",
+ "NC",
+ "NC (DISALLOWED)",
+ "DIV_CLK3",
+ "NC",
+ "NC",
+ "NC",
+ "NC (DISALLOWED)", /* GPIO_20 */
+ "NFC_CLK_REQ",
+ "NC (DISALLOWED)",
+ "WCSS_PWR_REQ",
+ "OPTION_1 (DISALLOWED)",
+ "OPTION_2 (DISALLOWED)",
+ "PM_SLB (DISALLOWED)";
+
+ vol_down_n: vol-down-n-state {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
bias-pull-up;
@@ -312,7 +345,7 @@ vol_down_pin_a: vol-down-active-state {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
- cam_focus_pin_a: cam-focus-btn-active-state {
+ focus_n: focus-n-state {
pins = "gpio7";
function = PMIC_GPIO_FUNC_NORMAL;
bias-pull-up;
@@ -320,7 +353,7 @@ cam_focus_pin_a: cam-focus-btn-active-state {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
- cam_snapshot_pin_a: cam-snapshot-btn-active-state {
+ snapshot_n: snapshot-n-state {
pins = "gpio8";
function = PMIC_GPIO_FUNC_NORMAL;
bias-pull-up;
@@ -328,7 +361,7 @@ cam_snapshot_pin_a: cam-snapshot-btn-active-state {
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
- audio_mclk_pin: audio-mclk-pin-active-state {
+ div_clk1: div-clk1-state {
pins = "gpio13";
function = "func2";
power-source = <0>;
@@ -336,7 +369,22 @@ audio_mclk_pin: audio-mclk-pin-active-state {
};
&pmi8998_gpio {
- cam_vio_default: cam-vio-active-state {
+ gpio-line-names = "MAIN_CAM_PWR_IO_EN", /* GPIO_1 */
+ "NC",
+ "NC",
+ "TYPEC_UUSB_SEL",
+ "VIB_LDO_EN",
+ "NC",
+ "DISPLAY_TYPE_SEL",
+ "NC",
+ "NC",
+ "NC", /* GPIO_10 */
+ "NC",
+ "DIV_CLK3",
+ "SPMI_I2C_SEL",
+ "NC";
+
+ main_cam_pwr_io_en: main-cam-pwr-io-en-state {
pins = "gpio1";
function = PMIC_GPIO_FUNC_NORMAL;
bias-disable;
@@ -346,7 +394,7 @@ cam_vio_default: cam-vio-active-state {
power-source = <1>;
};
- vib_default: vib-en-state {
+ vib_ldo_en: vib-ldo-en-state {
pins = "gpio5";
function = PMIC_GPIO_FUNC_NORMAL;
bias-disable;
@@ -595,8 +643,158 @@ &sdhc2 {
&tlmm {
gpio-reserved-ranges = <0 4>, <81 4>;
-
- mdp_vsync_n: mdp-vsync-n-state {
+ gpio-line-names = "", /* GPIO_0 */
+ "",
+ "",
+ "",
+ "DEBUG_UART_TX",
+ "DEBUG_UART_RX",
+ "CAMSENSOR_I2C_SDA",
+ "CAMSENSOR_I2C_SCL",
+ "NC",
+ "NC",
+ "MDP_VSYNC_P", /* GPIO_10 */
+ "RGBC_IR_INT",
+ "NFC_VEN",
+ "CAM_MCLK0",
+ "CAM_MCLK1",
+ "NC",
+ "NC",
+ "CCI_I2C_SDA0",
+ "CCI_I2C_SCL0",
+ "CCI_I2C_SDA1",
+ "CCI_I2C_SCL1", /* GPIO_20 */
+ "MAIN_CAM_PWR_EN",
+ "TOF_INT_N",
+ "NC",
+ "NC",
+ "CHAT_CAM_PWR_EN",
+ "NC",
+ "TOF_RESET_N",
+ "CAM2_RSTN",
+ "NC",
+ "CAM1_RSTN", /* GPIO_30 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "CC_DIR",
+ "UIM2_DETECT_EN",
+ "FP_RESET_N", /* GPIO_40 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "BT_HCI_UART_TXD",
+ "BT_HCI_UART_RXD",
+ "BT_HCI_UART_CTS_N",
+ "BT_HCI_UART_RFR_N",
+ "NC",
+ "NC", /* GPIO_50 */
+ "NC",
+ "NC",
+ "CODEC_INT2_N",
+ "CODEC_INT1_N",
+ "APPS_I2C_SDA",
+ "APPS_I2C_SCL",
+ "FORCED_USB_BOOT",
+ "NC",
+ "NC",
+ "NC", /* GPIO_60 */
+ "NC",
+ "NC",
+ "TRAY2_DET_DS",
+ "CODEC_RST_N",
+ "WSA_L_EN",
+ "WSA_R_EN",
+ "NC",
+ "NC",
+ "NC",
+ "LPASS_SLIMBUS_CLK", /* GPIO_70 */
+ "LPASS_SLIMBUS_DATA0",
+ "LPASS_SLIMBUS_DATA1",
+ "BT_FM_SLIMBUS_DATA",
+ "BT_FM_SLIMBUS_CLK",
+ "NC",
+ "RF_LCD_ID_EN",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO_80 */
+ "SW_SERVICE",
+ "TX_GTR_THRES_IN",
+ "HW_ID0",
+ "HW_ID1",
+ "NC",
+ "NC",
+ "TS_I2C_SDA",
+ "TS_I2C_SCL",
+ "TS_RESET_N",
+ "NC", /* GPIO_90 */
+ "NC",
+ "NFC_IRQ",
+ "NFC_DWLD_EN",
+ "DISP_RESET_N",
+ "TRAY2_DET",
+ "CAM_SOF",
+ "RFFE6_CLK",
+ "RFFE6_DATA",
+ "DEBUG_GPIO0",
+ "DEBUG_GPIO1", /* GPIO_100 */
+ "GRFC4",
+ "NC",
+ "NC",
+ "RSVD",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RESET",
+ "UIM2_PRESENT",
+ "UIM1_DATA",
+ "UIM1_CLK", /* GPIO_110 */
+ "UIM1_RST",
+ "UIM1_PRESENT",
+ "UIM_BATT_ALARM",
+ "RSVD",
+ "NC",
+ "NC",
+ "ACCEL_INT",
+ "GYRO_INT",
+ "COMPASS_INT",
+ "ALS_PROX_INT_N", /* GPIO_120 */
+ "FP_INT_N",
+ "NC",
+ "BAROMETER_INT",
+ "ACC_COVER_OPEN",
+ "TS_INT_N",
+ "NC",
+ "NC",
+ "USB_DETECT_EN",
+ "NC",
+ "QLINK_REQUEST", /* GPIO_130 */
+ "QLINK_ENABLE",
+ "NC",
+ "NC",
+ "WMSS_RESET_N",
+ "PA_INDICATOR_OR",
+ "NC",
+ "RFFE3_DATA",
+ "RFFE3_CLK",
+ "RFFE4_DATA",
+ "RFFE4_CLK", /* GPIO_140 */
+ "RFFE5_DATA",
+ "RFFE5_CLK",
+ "GNSS_EN",
+ "MSS_LTE_COXM_TXD",
+ "MSS_LTE_COXM_RXD",
+ "RFFE2_DATA",
+ "RFFE2_CLK",
+ "RFFE1_DATA",
+ "RFFE1_CLK";
+
+ mdp_vsync_p: mdp-vsync-p-state {
pins = "gpio10";
function = "mdp_vsync_a";
drive-strength = <2>;
@@ -611,14 +809,14 @@ nfc_ven: nfc-ven-state {
output-low;
};
- msm_mclk0_default: msm-mclk0-active-state {
+ cam_mclk0_active: cam-mclk0-active-state {
pins = "gpio13";
function = "cam_mclk";
drive-strength = <2>;
bias-disable;
};
- msm_mclk1_default: msm-mclk1-active-state {
+ cam_mclk1_active: cam-mclk1-active-state {
pins = "gpio14";
function = "cam_mclk";
drive-strength = <2>;
@@ -639,14 +837,14 @@ cci1_default: cci1-default-state {
drive-strength = <2>;
};
- cam0_vdig_default: cam0-vdig-default-state {
+ main_cam_pwr_en: main-cam-pwr-en-default-state {
pins = "gpio21";
function = "gpio";
bias-disable;
drive-strength = <2>;
};
- tof_int: tof-int-state {
+ tof_int_n: tof-int-n-state {
pins = "gpio22";
function = "gpio";
bias-pull-up;
@@ -654,28 +852,28 @@ tof_int: tof-int-state {
input-enable;
};
- cam1_vdig_default: cam1-vdig-default-state {
+ chat_cam_pwr_en: chat-cam-pwr-en-default-state {
pins = "gpio25";
function = "gpio";
bias-disable;
drive-strength = <2>;
};
- usb_extcon_active: usb-extcon-active-state {
- pins = "gpio38";
+ tof_reset: tof-reset-state {
+ pins = "gpio27";
function = "gpio";
bias-disable;
- drive-strength = <16>;
+ drive-strength = <2>;
};
- tof_reset: tof-reset-state {
- pins = "gpio27";
+ cc_dir_default: cc-dir-active-state {
+ pins = "gpio38";
function = "gpio";
bias-disable;
- drive-strength = <2>;
+ drive-strength = <16>;
};
- hall_sensor0_default: acc-cover-open-state {
+ acc_cover_open: acc-cover-open-state {
pins = "gpio124";
function = "gpio";
bias-disable;
@@ -690,7 +888,7 @@ ts_int_n: ts-int-n-state {
bias-pull-up;
};
- usb_vbus_active: usb-vbus-active-state {
+ usb_detect_en: usb-detect-en-active-state {
pins = "gpio128";
function = "gpio";
bias-disable;
--
2.39.0
