Re: [PATCH 3/3] arm64: dts: qcom: sm8150: Wire up MDSS

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Dec 12, 2022 at 10:33:14AM +0100, Konrad Dybcio wrote:
> Add required nodes for MDSS and hook up provided clocks in DISPCC.
> This setup is almost identical to 8[23]50.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/sm8150.dtsi | 271 ++++++++++++++++++++++++++-
>  1 file changed, 267 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> index ff04397777f4..c0c1e781eb43 100644
> --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
> @@ -9,6 +9,7 @@
>  #include <dt-bindings/power/qcom-rpmpd.h>
>  #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>  #include <dt-bindings/clock/qcom,rpmh.h>
> +#include <dt-bindings/clock/qcom,dispcc-sm8150.h>
>  #include <dt-bindings/clock/qcom,gcc-sm8150.h>
>  #include <dt-bindings/clock/qcom,gpucc-sm8150.h>
>  #include <dt-bindings/interconnect/qcom,osm-l3.h>
> @@ -3579,14 +3580,276 @@ camnoc_virt: interconnect@ac00000 {
>  			qcom,bcm-voters = <&apps_bcm_voter>;
>  		};
>  
> +		mdss: mdss@ae00000 {

As you're fixing up the dispcc patch, "display-subsystem@" seems nicer.

Regards,
Bjorn

> +			compatible = "qcom,sm8150-mdss";
> +			reg = <0 0x0ae00000 0 0x1000>;
> +			reg-names = "mdss";
> +
> +			interconnects = <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>,
> +					<&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>;
> +			interconnect-names = "mdp0-mem", "mdp1-mem";
> +
> +			power-domains = <&dispcc MDSS_GDSC>;
> +
> +			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +				 <&gcc GCC_DISP_HF_AXI_CLK>,
> +				 <&gcc GCC_DISP_SF_AXI_CLK>,
> +				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
> +			clock-names = "iface", "bus", "nrt_bus", "core";
> +
> +			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +
> +			iommus = <&apps_smmu 0x800 0x420>;
> +
> +			status = "disabled";
> +
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +
> +			mdss_mdp: display-controller@ae01000 {
> +				compatible = "qcom,sm8150-dpu";
> +				reg = <0 0x0ae01000 0 0x8f000>,
> +				      <0 0x0aeb0000 0 0x2008>;
> +				reg-names = "mdp", "vbif";
> +
> +				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_DISP_HF_AXI_CLK>,
> +					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
> +					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				clock-names = "iface", "bus", "core", "vsync";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> +				assigned-clock-rates = <19200000>;
> +
> +				operating-points-v2 = <&mdp_opp_table>;
> +				power-domains = <&rpmhpd SM8150_MMCX>;
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dpu_intf1_out: endpoint {
> +							remote-endpoint = <&mdss_dsi0_in>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dpu_intf2_out: endpoint {
> +							remote-endpoint = <&mdss_dsi1_in>;
> +						};
> +					};
> +				};
> +
> +				mdp_opp_table: opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-171428571 {
> +						opp-hz = /bits/ 64 <171428571>;
> +						required-opps = <&rpmhpd_opp_low_svs>;
> +					};
> +
> +					opp-300000000 {
> +						opp-hz = /bits/ 64 <300000000>;
> +						required-opps = <&rpmhpd_opp_svs>;
> +					};
> +
> +					opp-345000000 {
> +						opp-hz = /bits/ 64 <345000000>;
> +						required-opps = <&rpmhpd_opp_svs_l1>;
> +					};
> +
> +					opp-460000000 {
> +						opp-hz = /bits/ 64 <460000000>;
> +						required-opps = <&rpmhpd_opp_nom>;
> +					};
> +				};
> +			};
> +
> +			mdss_dsi0: dsi@ae94000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0 0x0ae94000 0 0x400>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <4>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> +					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_DISP_HF_AXI_CLK>;
> +				clock-names = "byte",
> +					      "byte_intf",
> +					      "pixel",
> +					      "core",
> +					      "iface",
> +					      "bus";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
> +						  <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
> +				assigned-clock-parents = <&mdss_dsi0_phy 0>,
> +							 <&mdss_dsi0_phy 1>;
> +
> +				operating-points-v2 = <&dsi_opp_table>;
> +				power-domains = <&rpmhpd SM8150_MMCX>;
> +
> +				phys = <&mdss_dsi0_phy>;
> +
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						mdss_dsi0_in: endpoint {
> +							remote-endpoint = <&dpu_intf1_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						mdss_dsi0_out: endpoint {
> +						};
> +					};
> +				};
> +
> +				dsi_opp_table: opp-table {
> +					compatible = "operating-points-v2";
> +
> +					opp-187500000 {
> +						opp-hz = /bits/ 64 <187500000>;
> +						required-opps = <&rpmhpd_opp_low_svs>;
> +					};
> +
> +					opp-300000000 {
> +						opp-hz = /bits/ 64 <300000000>;
> +						required-opps = <&rpmhpd_opp_svs>;
> +					};
> +
> +					opp-358000000 {
> +						opp-hz = /bits/ 64 <358000000>;
> +						required-opps = <&rpmhpd_opp_svs_l1>;
> +					};
> +				};
> +			};
> +
> +			mdss_dsi0_phy: phy@ae94400 {
> +				compatible = "qcom,dsi-phy-7nm";
> +				reg = <0 0x0ae94400 0 0x200>,
> +				      <0 0x0ae94600 0 0x280>,
> +				      <0 0x0ae94900 0 0x260>;
> +				reg-names = "dsi_phy",
> +					    "dsi_phy_lane",
> +					    "dsi_pll";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&rpmhcc RPMH_CXO_CLK>;
> +				clock-names = "iface", "ref";
> +
> +				status = "disabled";
> +			};
> +
> +			mdss_dsi1: dsi@ae96000 {
> +				compatible = "qcom,mdss-dsi-ctrl";
> +				reg = <0 0x0ae96000 0 0x400>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <5>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
> +					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
> +					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&gcc GCC_DISP_HF_AXI_CLK>;
> +				clock-names = "byte",
> +					      "byte_intf",
> +					      "pixel",
> +					      "core",
> +					      "iface",
> +					      "bus";
> +
> +				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>,
> +						  <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
> +				assigned-clock-parents = <&mdss_dsi1_phy 0>,
> +							 <&mdss_dsi1_phy 1>;
> +
> +				operating-points-v2 = <&dsi_opp_table>;
> +				power-domains = <&rpmhpd SM8150_MMCX>;
> +
> +				phys = <&mdss_dsi1_phy>;
> +
> +				status = "disabled";
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						mdss_dsi1_in: endpoint {
> +							remote-endpoint = <&dpu_intf2_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						mdss_dsi1_out: endpoint {
> +						};
> +					};
> +				};
> +			};
> +
> +			mdss_dsi1_phy: phy@ae96400 {
> +				compatible = "qcom,dsi-phy-7nm";
> +				reg = <0 0x0ae96400 0 0x200>,
> +				      <0 0x0ae96600 0 0x280>,
> +				      <0 0x0ae96900 0 0x260>;
> +				reg-names = "dsi_phy",
> +					    "dsi_phy_lane",
> +					    "dsi_pll";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> +					 <&rpmhcc RPMH_CXO_CLK>;
> +				clock-names = "iface", "ref";
> +
> +				status = "disabled";
> +			};
> +		};
> +
>  		dispcc: clock-controller@af00000 {
>  			compatible = "qcom,sm8150-dispcc";
>  			reg = <0 0x0af00000 0 0x10000>;
>  			clocks = <&rpmhcc RPMH_CXO_CLK>,
> -				 <0>,
> -				 <0>,
> -				 <0>,
> -				 <0>,
> +				 <&mdss_dsi0_phy 0>,
> +				 <&mdss_dsi0_phy 1>,
> +				 <&mdss_dsi1_phy 0>,
> +				 <&mdss_dsi1_phy 1>,
>  				 <0>,
>  				 <0>;
>  			clock-names = "bi_tcxo",
> -- 
> 2.38.1
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux