Re: [PATCH] arm64: dts: qcom: sm6115: Move SDHC node(s)'s 'pinctrl' properties to dts

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2022-12-20 17:06:16, Bhupesh Sharma wrote:
> Normally the 'pinctrl' properties of a SDHC controller and the
> chip detect pin settings are dependent on the type of the slots
> (for e.g uSD card slot), regulators and GPIO(s) available on the
> board(s).

I always thought it was okay to give the `sdcX_*` pins to the sdhc_X
node unconditionally in SoC DTSI, and leave board-dependent card-detect
(if this SDHCI slot is even used for removable cards) pins to the board
DTS.

> So, move the same from the sm6115 dtsi file to the respective
> board file(s).
> 
> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@xxxxxxxxxx>

Thanks for cleaning this up, we're already using this pattern in quite a
few SoCs now.

Reviewed-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>

Though...

> ---
>  .../boot/dts/qcom/sm4250-oneplus-billie2.dts  | 10 +++++++++
>  arch/arm64/boot/dts/qcom/sm6115.dtsi          | 22 -------------------
>  2 files changed, 10 insertions(+), 22 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts b/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
> index a3f1c7c41fd73..329eb496bbc5f 100644
> --- a/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
> +++ b/arch/arm64/boot/dts/qcom/sm4250-oneplus-billie2.dts
> @@ -202,12 +202,22 @@ &sdhc_2 {
>  	vqmmc-supply = <&vreg_l5a>;
>  
>  	cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>;
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&sdc2_state_on &sdc2_card_det_n>;
> +	pinctrl-1 = <&sdc2_state_off &sdc2_card_det_n>;
>  
>  	status = "okay";
>  };
>  
>  &tlmm {
>  	gpio-reserved-ranges = <14 4>;
> +
> +	sdc2_card_det_n: sd-card-det-n-state {
> +		pins = "gpio88";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-up;

Note that SoC DTSI uses bias-disable in the off state.

> +	};
>  };
>  
>  &ufs_mem_hc {
> diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> index 572bf04adf906..6be763d39870d 100644
> --- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> @@ -518,13 +518,6 @@ data-pins {
>  					bias-pull-up;
>  					drive-strength = <10>;
>  				};
> -
> -				sd-cd-pins {
> -					pins = "gpio88";
> -					function = "gpio";
> -					bias-pull-up;
> -					drive-strength = <2>;
> -				};
>  			};
>  
>  			sdc2_state_off: sdc2-off-state {
> @@ -545,13 +538,6 @@ data-pins {
>  					bias-pull-up;
>  					drive-strength = <2>;
>  				};
> -
> -				sd-cd-pins {
> -					pins = "gpio88";
> -					function = "gpio";
> -					bias-disable;
> -					drive-strength = <2>;
> -				};
>  			};
>  		};
>  
> @@ -652,10 +638,6 @@ sdhc_1: mmc@4744000 {
>  				 <&gcc GCC_SDCC1_ICE_CORE_CLK>;
>  			clock-names = "iface", "core", "xo", "ice";
>  
> -			pinctrl-0 = <&sdc1_state_on>;
> -			pinctrl-1 = <&sdc1_state_off>;
> -			pinctrl-names = "default", "sleep";
> -

You can probably leave these and below?  Only boards needing to extend
pinctrl with board-specific SDCard pins would have to update/override
these properties that way?

- Marijn

>  			bus-width = <8>;
>  			status = "disabled";
>  		};
> @@ -672,10 +654,6 @@ sdhc_2: mmc@4784000 {
>  			clocks = <&gcc GCC_SDCC2_AHB_CLK>, <&gcc GCC_SDCC2_APPS_CLK>, <&xo_board>;
>  			clock-names = "iface", "core", "xo";
>  
> -			pinctrl-0 = <&sdc2_state_on>;
> -			pinctrl-1 = <&sdc2_state_off>;
> -			pinctrl-names = "default", "sleep";
> -
>  			power-domains = <&rpmpd SM6115_VDDCX>;
>  			operating-points-v2 = <&sdhc2_opp_table>;
>  			iommus = <&apps_smmu 0x00a0 0x0>;
> -- 
> 2.38.1
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux