On 20/12/2022 09:01, Jim Liu wrote: > Add dt-bindings document for the NPCM7xx sgpio driver > > Signed-off-by: Jim Liu <JJLIU0@xxxxxxxxxxx> > --- > Changes for v3: > - modify description > - modify in/out property name > Changes for v2: > - modify description > --- > .../bindings/gpio/nuvoton,sgpio.yaml | 83 +++++++++++++++++++ > 1 file changed, 83 insertions(+) > create mode 100644 Documentation/devicetree/bindings/gpio/nuvoton,sgpio.yaml > > diff --git a/Documentation/devicetree/bindings/gpio/nuvoton,sgpio.yaml b/Documentation/devicetree/bindings/gpio/nuvoton,sgpio.yaml > new file mode 100644 > index 000000000000..673535314cff > --- /dev/null > +++ b/Documentation/devicetree/bindings/gpio/nuvoton,sgpio.yaml > @@ -0,0 +1,83 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/gpio/nuvoton,sgpio.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Nuvoton SGPIO controller > + > +maintainers: > + - Jim LIU <JJLIU0@xxxxxxxxxxx> > + > +description: > + This SGPIO controller is for NUVOTON NPCM7xx and NPCM8xx SoC. > + Nuvoton NPCM7xx SGPIO module is combine serial to parallel IC (HC595) > + and parallel to serial IC (HC165), and use APB3 clock to control it. > + This interface has 4 pins (D_out , D_in, S_CLK, LDSH). > + NPCM7xx/NPCM8xx have two sgpio module each module can support up > + to 64 output pins,and up to 64 input pin, the pin is only for gpi or gpo. > + GPIO pins have sequential, First half is gpo and second half is gpi. > + GPIO pins can be programmed to support the following options > + - Support interrupt option for each input port and various interrupt > + sensitivity option (level-high, level-low, edge-high, edge-low) > + - Directly connected to APB bus and its shift clock is from APB bus clock > + divided by a programmable value. > + - ngpios is number of nuvoton,input-ngpios GPIO lines and nuvoton,output-ngpios GPIO lines. > + nuvoton,input-ngpios GPIO lines is only for gpi. > + nuvoton,output-ngpios GPIO lines is only for gpo. > + > +properties: > + compatible: > + enum: > + - nuvoton,npcm750-sgpio > + - nuvoton,npcm845-sgpio > + > + reg: > + maxItems: 1 > + > + gpio-controller: true > + > + '#gpio-cells': > + const: 2 > + > + interrupts: > + maxItems: 1 > + > + clocks: > + maxItems: 1 > + > + nuvoton,input-ngpios: true > + > + nuvoton,output-ngpios: true You did not solve previous comments. Fields cannot be just "true" but need description, type and constraints. You need to solve previous comments. > + > + bus-frequency: true This is a friendly reminder during the review process. It seems my previous comments were not fully addressed. Maybe my feedback got lost between the quotes, maybe you just forgot to apply it. Please go back to the previous discussion and either implement all requested changes or keep discussing them. Thank you. > + > +required: > + - compatible > + - reg > + - gpio-controller > + - '#gpio-cells' > + - interrupts > + - nuvoton,input-ngpios > + - nuvoton,output-ngpios > + - clocks > + - bus-frequency > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/nuvoton,npcm7xx-clock.h> > + #include <dt-bindings/interrupt-controller/arm-gic.h> > + gpio8: gpio@101000 { > + compatible = "nuvoton,npcm750-sgpio"; > + reg = <0x101000 0x200>; > + clocks = <&clk NPCM7XX_CLK_APB3>; > + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; > + bus-frequency = <16000000>; > + gpio-controller; > + #gpio-cells = <2>; > + nuvoton,input-ngpios = <64>; > + nuvoton,output-ngpios = <64>; > + status = "disabled"; This is a friendly reminder during the review process. It seems my previous comments were not fully addressed. Maybe my feedback got lost between the quotes, maybe you just forgot to apply it. Please go back to the previous discussion and either implement all requested changes or keep discussing them. Thank you. > + }; Best regards, Krzysztof
