On 11/03/2014 04:30 PM, Nishanth Menon wrote:
> On 12:09-20141103, Roger Quadros wrote:
>> For PIN_OUTPUT_PULLUP and PIN_OUTPUT_PULLDOWN we must not set the
>> PULL_DIS bit which disables the PULLs.
>>
>> PULL_ENA is a 0 and using it in an OR operation is a NOP, so don't
>> use it in the PIN_OUTPUT_PULLUP/DOWN macros.
>>
>> Fixes: 23d9cec07c58 ("pinctrl: dra: dt-bindings: Fix pull enable/disable")
>>
>> Signed-off-by: Roger Quadros <rogerq@xxxxxx>
>> ---
>> include/dt-bindings/pinctrl/dra.h | 4 ++--
>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>
>> diff --git a/include/dt-bindings/pinctrl/dra.h b/include/dt-bindings/pinctrl/dra.h
>> index 3d33794..7448edf 100644
>> --- a/include/dt-bindings/pinctrl/dra.h
>> +++ b/include/dt-bindings/pinctrl/dra.h
>> @@ -40,8 +40,8 @@
>>
>> /* Active pin states */
>> #define PIN_OUTPUT (0 | PULL_DIS)
>> -#define PIN_OUTPUT_PULLUP (PIN_OUTPUT | PULL_ENA | PULL_UP)
>> -#define PIN_OUTPUT_PULLDOWN (PIN_OUTPUT | PULL_ENA)
>> +#define PIN_OUTPUT_PULLUP (PULL_UP)
>> +#define PIN_OUTPUT_PULLDOWN (0)
>> #define PIN_INPUT (INPUT_EN | PULL_DIS)
>> #define PIN_INPUT_SLEW (INPUT_EN | SLEWCONTROL)
>> #define PIN_INPUT_PULLUP (PULL_ENA | INPUT_EN | PULL_UP)
>
> You are right, we do have an issue with using PIN_OUTPUT along with
> remaining setting.
>
> For a moment, I wondered why input was not impacted - then I realized
> that INPUT_EN was being used instead of PIN_INPUT - following that
> convention. With the intent being explicitly using macros that
> clearly indicate what each setting combination is is, how about the
> following?
>
>
> diff --git a/include/dt-bindings/pinctrl/dra.h b/include/dt-bindings/pinctrl/dra.h
> index 3d33794..d4037e7 100644
> --- a/include/dt-bindings/pinctrl/dra.h
> +++ b/include/dt-bindings/pinctrl/dra.h
> @@ -34,14 +34,15 @@
> #define PULL_DIS (1 << 16)
> #define PULL_UP (1 << 17)
> #define INPUT_EN (1 << 18)
> +#define OUTPUT_EN (0 << 18)
> #define SLEWCONTROL (1 << 19)
> #define WAKEUP_EN (1 << 24)
> #define WAKEUP_EVENT (1 << 25)
>
> /* Active pin states */
> -#define PIN_OUTPUT (0 | PULL_DIS)
> -#define PIN_OUTPUT_PULLUP (PIN_OUTPUT | PULL_ENA | PULL_UP)
> -#define PIN_OUTPUT_PULLDOWN (PIN_OUTPUT | PULL_ENA)
> +#define PIN_OUTPUT (OUTPUT_EN | PULL_DIS)
> +#define PIN_OUTPUT_PULLUP (OUTPUT_EN | PULL_ENA | PULL_UP)
> +#define PIN_OUTPUT_PULLDOWN (OUTPUT_EN | PULL_ENA)
To me it adds more confusion and this change is a NOP as we're ORing 0 here
with OUTPUT_EN.
> #define PIN_INPUT (INPUT_EN | PULL_DIS)
> #define PIN_INPUT_SLEW (INPUT_EN | SLEWCONTROL)
> #define PIN_INPUT_PULLUP (PULL_ENA | INPUT_EN | PULL_UP)
>
cheers,
-roger
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
