On 16/12/2022 00:37, Adam Ford wrote:
> Beacon Embedded has an i.MX8M Plus development kit which consists
> of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
> and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
> Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
> PHY.
>
> Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-beacon-kit.dts b/arch/arm64/boot/dts/freescale/imx8mp-beacon-kit.dts
> new file mode 100644
> index 000000000000..80131cf318ea
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-beacon-kit.dts
> @@ -0,0 +1,576 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2022 Logic PD, Inc dba Beacon EmbeddedWorks
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/usb/pd.h>
> +#include <dt-bindings/phy/phy-imx8-pcie.h>
> +#include "imx8mp.dtsi"
> +#include "imx8mp-beacon-som.dtsi"
> +
> +/ {
> + model = "Beacon EmbeddedWorks i.MX8MPlus Development kit";
> + compatible = "beacon,imx8mp-beacon-kit", "fsl,imx8mp";
> +
> + aliases {
> + ethernet0 = &eqos;
> + ethernet1 = &fec;
> + };
> +
> + chosen {
> + stdout-path = &uart2;
> + };
> +
> + connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port@0 {
> + reg = <0>;
> + hs_ep: endpoint {
> + remote-endpoint = <&usb3_hs_ep>;
> + };
> + };
> + port@1 {
> + reg = <1>;
> + ss_ep: endpoint {
> + remote-endpoint = <&hd3ss3220_in_ep>;
> + };
> + };
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + autorepeat;
> +
> + btn0 {
Does not look like you tested the bindings. Please run `make
dt_binding_check` (see
Documentation/devicetree/bindings/writing-schema.rst for instructions).
> + label = "btn0";
> + linux,code = <BTN_0>;
> + gpios = <&pca6416_1 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + wakeup-source;
> + };
> +
> + btn1 {
> + label = "btn1";
> + linux,code = <BTN_1>;
> + gpios = <&pca6416_1 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + wakeup-source;
> + };
> +
> + btn2 {
> + label = "btn2";
> + linux,code = <BTN_2>;
> + gpios = <&pca6416_1 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + wakeup-source;
> + };
> +
> + btn3 {
> + label = "btn3";
> + linux,code = <BTN_3>;
> + gpios = <&pca6416_1 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + wakeup-source;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led0 {
I think preferred is led-0
> + label = "gen_led0";
> + gpios = <&pca6416_1 4 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + led1 {
led-1
> + label = "gen_led1";
> + gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + led2 {
> + label = "gen_led2";
> + gpios = <&pca6416_1 6 GPIO_ACTIVE_HIGH>;
> + default-state = "off";
> + };
> +
> + led3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_led3>;
> + label = "heartbeat";
> + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + pcie0_refclk: pcie0-refclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <100000000>;
> + };
> +
> + reg_usdhc2_vmmc: regulator-usdhc2 {
> + compatible = "regulator-fixed";
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + startup-delay-us = <100>;
> + off-on-delay-us = <20000>;
> + };
> +
> + reg_usb1_host_vbus: regulator-usb1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb1_host_vbus";
> + regulator-max-microvolt = <5000000>;
> + regulator-min-microvolt = <5000000>;
> + gpio = <&pca6416_1 0 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&ecspi2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + fsl,spi-num-chipselects = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +
> + tpm: tpm_tis@0 {
Node names should be generic. No underscores in node name.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tpm>;
> + compatible = "infineon,slb9670";
> + reg = <0>;
compatible is the first propert, reg is second.
> + reset-gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
> + spi-max-frequency = <18500000>;
> + };
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy1>;
> + phy-reset-gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
> + phy-reset-post-delay = <150>;
> + phy-reset-duration = <10>;
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy1: ethernet1-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <3>;
> + };
> + };
> +};
> +
> +&flexcan1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + status = "okay";
> +};
> +
> +
> +&i2c2 {
> + clock-frequency = <384000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + pca6416_3: gpio-i2c2@20 {
Node names should be generic, so i2c
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "nxp,pcal6416";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +};
> +
> +&i2c3 {
> + /* Connected to USB Hub */
> + ptn5110: tcpc@52 {
What is a tcpc?
> + compatible = "nxp,ptn5110";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_typec>;
> + reg = <0x52>;
Order of your properties is quite random...
> + interrupt-parent = <&gpio4>;
> + interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
> +
> + usb_con: connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + power-role = "source";
> + data-role = "host";
> + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + };
> + };
> +};
> +
> +&i2c4 {
> + clock-frequency = <384000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c4>;
> + status = "okay";
> +
> + pca6416: gpio@20 {
> + compatible = "nxp,pcal6416";
> + reg = <0x20>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcal6414>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + pca6416_1: gpio@21 {
> + compatible = "nxp,pcal6416";
> + reg = <0x21>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-parent = <&gpio4>;
> + interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + usb-reset {
> + gpio-hog;
> + gpios = <7 0>;
> + output-low;
> + line-name = "USB Hub Reset";
> + };
> + };
> +
> + hd3ss3220@47 {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hd3ss3220>;
> + compatible = "ti,hd3ss3220";
> + reg = <0x47>;
pinctrl is not the first property.
> + interrupt-parent = <&gpio4>;
> + interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + port@0 {
> + reg = <0>;
> + hd3ss3220_in_ep: endpoint {
> + remote-endpoint = <&ss_ep>;
> + };
> + };
> + port@1 {
> + reg = <1>;
Wrong indentation.
> + hd3ss3220_out_ep: endpoint {
> + remote-endpoint = <&usb3_role_switch>;
> + };
> + };
> + };
> + };
> +};
> +
> +&gpio2 {
> + usb-reset {
Does it pass dtbs_check?
> + gpio-hog;
> + gpios = <20 0>;
> + output-low;
> + line-name = "USB-C Mux En";
> + };
> +};
> +
> +&pcie {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pcie>;
> + disable-gpio = <&gpio1 5 GPIO_ACTIVE_LOW>;
> + reset-gpio = <&gpio4 21 GPIO_ACTIVE_LOW>;
> + clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
> + <&clk IMX8MP_CLK_PCIE_ROOT>,
> + <&clk IMX8MP_CLK_HSIO_AXI>;
> + clock-names = "pcie", "pcie_aux", "pcie_bus";
> + assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>;
> + assigned-clock-rates = <10000000>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>;
> + status = "okay";
> +};
(...)
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi
> new file mode 100644
> index 000000000000..c915116cfc4b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi
> @@ -0,0 +1,500 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright LogicPD, Inc. dba Beacon EmbeddedWorks
> + */
> +
> +/ {
> + aliases {
> + rtc0 = &rtc;
> + rtc1 = &snvs_rtc;
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + reg = <0x0 0x40000000 0 0xc0000000>,
> + <0x1 0x00000000 0 0xc0000000>;
> + };
> +
> + reg_wl_bt: regulator-wl-bt-pow-dwn {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_wl_bt>;
> + interrupt-parent = <&gpio1>;
> + compatible = "regulator-fixed";
> + regulator-name = "wl-bt-pow-dwn";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 6 GPIO_ACTIVE_LOW>;
> + startup-delay-us = <70000>;
> + regulator-always-on;
> + };
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <&buck2>;
> +};
> +
> +&dsp {
> + status = "okay";
> +};
> +
> +&eqos {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_eqos>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy0>;
> + snps,force_thresh_dma_mode;
> + snps,mtl-tx-config = <&mtl_tx_setup>;
> + snps,mtl-rx-config = <&mtl_rx_setup>;
> + status = "okay";
> +
> + mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@3 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + interrupt-parent = <&gpio1>;
> + interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
> + reg = <3>;
> + };
> + };
> +
> + mtl_tx_setup: tx-queues-config {
> + snps,tx-queues-to-use = <5>;
> + snps,tx-sched-sp;
> +
> + queue0 {
> + snps,dcb-algorithm;
> + snps,priority = <0x1>;
> + };
> +
> + queue1 {
> + snps,dcb-algorithm;
> + snps,priority = <0x2>;
> + };
> +
> + queue2 {
> + snps,dcb-algorithm;
> + snps,priority = <0x4>;
> + };
> +
> + queue3 {
> + snps,dcb-algorithm;
> + snps,priority = <0x8>;
> + };
> +
> + queue4 {
> + snps,dcb-algorithm;
> + snps,priority = <0xf0>;
> + };
> + };
> +
> + mtl_rx_setup: rx-queues-config {
> + snps,rx-queues-to-use = <5>;
> + snps,rx-sched-sp;
> +
> + queue0 {
> + snps,dcb-algorithm;
> + snps,priority = <0x1>;
> + snps,map-to-dma-channel = <0>;
> + };
> +
> + queue1 {
> + snps,dcb-algorithm;
> + snps,priority = <0x2>;
> + snps,map-to-dma-channel = <1>;
> + };
> +
> + queue2 {
> + snps,dcb-algorithm;
> + snps,priority = <0x4>;
> + snps,map-to-dma-channel = <2>;
> + };
> +
> + queue3 {
> + snps,dcb-algorithm;
> + snps,priority = <0x8>;
> + snps,map-to-dma-channel = <3>;
> + };
> +
> + queue4 {
> + snps,dcb-algorithm;
> + snps,priority = <0xf0>;
> + snps,map-to-dma-channel = <4>;
> + };
> + };
> +};
> +
> +&flexspi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexspi0>;
> + status = "okay";
> +
> + flash0: mt25qu256aba@0 {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "jedec,spi-nor";
> + spi-max-frequency = <80000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <4>;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <384000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + pmic@25 {
> + compatible = "nxp,pca9450c";
> + reg = <0x25>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pmic>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +
> + regulators {
> + buck1: BUCK1 {
> + regulator-name = "BUCK1";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + buck2: BUCK2 {
> + regulator-name = "BUCK2";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <2187500>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + nxp,dvs-run-voltage = <950000>;
> + nxp,dvs-standby-voltage = <850000>;
> + };
> +
> + buck4: BUCK4 {
> + regulator-name = "BUCK4";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck5: BUCK5 {
> + regulator-name = "BUCK5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buck6: BUCK6 {
> + regulator-name = "BUCK6";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <3400000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1600000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo3: LDO3 {
> + regulator-name = "LDO3";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo4: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo5: LDO5 {
> + regulator-name = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <384000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + status = "okay";
> +
> + eeprom@50 {
> + compatible = "atmel,24c64";
> + pagesize = <32>;
> + read-only; /* Manufacturing EEPROM programmed at factory */
> + reg = <0x50>;
reg is second property
> + };
> +
> + rtc: rtc@51 {
> + compatible = "nxp,pcf85263";
> + reg = <0x51>;
> + quartz-load-femtofarads = <12500>;
> + };
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + assigned-clocks = <&clk IMX8MP_CLK_UART1>;
> + assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>;
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&usdhc1 {
> + vmmc-supply = <®_wl_bt>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + bus-width = <4>;
> + max-frequency = <200000000>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + keep-power-in-suspend;
> + enable-sdio-wakeup;
> + cap-sdio-irq;
> + non-removable;
> + cap-power-off-card;
> + status = "okay";
status is usually last
> + #address-cells = <1>;
> + #size-cells = <0>;
Do you need these?
> +
> + mwifiex: wifi@1 {
> + reg = <1>;
> + compatible = "marvell,sd8997";
compatible, then reg
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wlan>;
> + interrupt-parent = <&gpio2>;
> + interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
Best regards,
Krzysztof
