Re: [PATCH net-next] powerpc: dts: t208x: Disable 10G on MAC1 and MAC2

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 12/15/22 11:12, Camelia Alexandra Groza wrote:
>> -----Original Message-----
>> From: Sean Anderson <sean.anderson@xxxxxxxx>
>> Sent: Thursday, November 3, 2022 23:29
>> To: David S . Miller <davem@xxxxxxxxxxxxx>; netdev@xxxxxxxxxxxxxxx
>> Cc: devicetree@xxxxxxxxxxxxxxx; Michael Ellerman <mpe@xxxxxxxxxxxxxx>;
>> linux-kernel@xxxxxxxxxxxxxxx; Rob Herring <robh+dt@xxxxxxxxxx>;
>> Christophe Leroy <christophe.leroy@xxxxxxxxxx>; linuxppc-
>> dev@xxxxxxxxxxxxxxxx; Nicholas Piggin <npiggin@xxxxxxxxx>; Krzysztof
>> Kozlowski <krzysztof.kozlowski+dt@xxxxxxxxxx>; Sean Anderson
>> <sean.anderson@xxxxxxxx>; Camelia Alexandra Groza
>> <camelia.groza@xxxxxxx>
>> Subject: [PATCH net-next] powerpc: dts: t208x: Disable 10G on MAC1 and
>> MAC2
>> 
>> There aren't enough resources to run these ports at 10G speeds. Just
>> keep the pcs changes, and revert the rest. This is not really correct,
>> since the hardware could support 10g in some other configuration...
>> 
>> Fixes: 36926a7d70c2 ("powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G")
>> Reported-by: Camelia Alexandra Groza <camelia.groza@xxxxxxx>
>> Signed-off-by: Sean Anderson <sean.anderson@xxxxxxxx>
>> ---
>> 
> 
> Hi Sean,
> 
> I know I'm late, but there are a couple of issues with this patch. Do you intend
> on sending a v2 or should I pick it up?
> 
>>  .../boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi     | 45 -------------------
>>  .../boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi     | 45 -------------------
>>  arch/powerpc/boot/dts/fsl/t2081si-post.dtsi   |  6 ++-
>>  3 files changed, 4 insertions(+), 92 deletions(-)
>>  delete mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
>>  delete mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
>> 
>> diff --git a/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
>> b/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
>> deleted file mode 100644
>> index 6b3609574b0f..000000000000
>> --- a/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
>> +++ /dev/null
>> @@ -1,45 +0,0 @@
>> -// SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0-or-later
>> -/*
>> - * QorIQ FMan v3 10g port #2 device tree stub [ controller @ offset
>> 0x400000 ]
>> - *
>> - * Copyright 2022 Sean Anderson <sean.anderson@xxxxxxxx>
>> - * Copyright 2012 - 2015 Freescale Semiconductor Inc.
>> - */
>> -
>> -fman@400000 {
>> -	fman0_rx_0x08: port@88000 {
>> -		cell-index = <0x8>;
>> -		compatible = "fsl,fman-v3-port-rx";
>> -		reg = <0x88000 0x1000>;
>> -		fsl,fman-10g-port;
>> -	};
>> -
>> -	fman0_tx_0x28: port@a8000 {
>> -		cell-index = <0x28>;
>> -		compatible = "fsl,fman-v3-port-tx";
>> -		reg = <0xa8000 0x1000>;
>> -		fsl,fman-10g-port;
>> -	};
>> -
>> -	ethernet@e0000 {
>> -		cell-index = <0>;
>> -		compatible = "fsl,fman-memac";
>> -		reg = <0xe0000 0x1000>;
>> -		fsl,fman-ports = <&fman0_rx_0x08 &fman0_tx_0x28>;
>> -		ptp-timer = <&ptp_timer0>;
>> -		pcsphy-handle = <&pcsphy0>, <&pcsphy0>;
>> -		pcs-handle-names = "sgmii", "xfi";
>> -	};
>> -
>> -	mdio@e1000 {
>> -		#address-cells = <1>;
>> -		#size-cells = <0>;
>> -		compatible = "fsl,fman-memac-mdio", "fsl,fman-xmdio";
>> -		reg = <0xe1000 0x1000>;
>> -		fsl,erratum-a011043; /* must ignore read errors */
>> -
>> -		pcsphy0: ethernet-phy@0 {
>> -			reg = <0x0>;
>> -		};
>> -	};
>> -};
>> diff --git a/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
>> b/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
>> deleted file mode 100644
>> index 28ed1a85a436..000000000000
>> --- a/arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi
>> +++ /dev/null
>> @@ -1,45 +0,0 @@
>> -// SPDX-License-Identifier: BSD-3-Clause OR GPL-2.0-or-later
>> -/*
>> - * QorIQ FMan v3 10g port #3 device tree stub [ controller @ offset
>> 0x400000 ]
>> - *
>> - * Copyright 2022 Sean Anderson <sean.anderson@xxxxxxxx>
>> - * Copyright 2012 - 2015 Freescale Semiconductor Inc.
>> - */
>> -
>> -fman@400000 {
>> -	fman0_rx_0x09: port@89000 {
>> -		cell-index = <0x9>;
>> -		compatible = "fsl,fman-v3-port-rx";
>> -		reg = <0x89000 0x1000>;
>> -		fsl,fman-10g-port;
>> -	};
>> -
>> -	fman0_tx_0x29: port@a9000 {
>> -		cell-index = <0x29>;
>> -		compatible = "fsl,fman-v3-port-tx";
>> -		reg = <0xa9000 0x1000>;
>> -		fsl,fman-10g-port;
>> -	};
>> -
>> -	ethernet@e2000 {
>> -		cell-index = <1>;
>> -		compatible = "fsl,fman-memac";
>> -		reg = <0xe2000 0x1000>;
>> -		fsl,fman-ports = <&fman0_rx_0x09 &fman0_tx_0x29>;
>> -		ptp-timer = <&ptp_timer0>;
>> -		pcsphy-handle = <&pcsphy1>, <&pcsphy1>;
>> -		pcs-handle-names = "sgmii", "xfi";
>> -	};
>> -
>> -	mdio@e3000 {
>> -		#address-cells = <1>;
>> -		#size-cells = <0>;
>> -		compatible = "fsl,fman-memac-mdio", "fsl,fman-xmdio";
>> -		reg = <0xe3000 0x1000>;
>> -		fsl,erratum-a011043; /* must ignore read errors */
>> -
>> -		pcsphy1: ethernet-phy@0 {
>> -			reg = <0x0>;
>> -		};
>> -	};
>> -};
>> diff --git a/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
>> b/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
>> index 74e17e134387..fed3879fa0aa 100644
>> --- a/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
>> +++ b/arch/powerpc/boot/dts/fsl/t2081si-post.dtsi
>> @@ -609,8 +609,8 @@ usb1: usb@211000 {
>>  /include/ "qoriq-bman1.dtsi"
>> 
>>  /include/ "qoriq-fman3-0.dtsi"
>> -/include/ "qoriq-fman3-0-10g-2.dtsi"
>> -/include/ "qoriq-fman3-0-10g-3.dtsi"
>> +/include/ "qoriq-fman3-0-1g-2.dtsi"
>> +/include/ "qoriq-fman3-0-1g-3.dtsi"
> 
> These two should be qoriq-fman3-0-1g-0.dtsi and qoriq-fman3-0-1g-1.dtsi.
> You are including 1g-2.dtsi and 1g-3.dtsi twice.

So they should.

>>  /include/ "qoriq-fman3-0-1g-2.dtsi"
>>  /include/ "qoriq-fman3-0-1g-3.dtsi"
>>  /include/ "qoriq-fman3-0-1g-4.dtsi"
>> @@ -619,9 +619,11 @@ usb1: usb@211000 {
>>  /include/ "qoriq-fman3-0-10g-1.dtsi"
>>  	fman@400000 {
>>  		enet0: ethernet@e0000 {
>> +			pcs-handle-names = "sgmii", "xfi";
>>  		};
>> 
>>  		enet1: ethernet@e2000 {
>> +			pcs-handle-names = "sgmii", "xfi";
> 
> The second pcsphy for this port is still qsgmiia_pcs1 as described in
> qoriq-fman3-0-1g-1.dtsi. It should also be overwritten, not only the name
> property:
> 	pcsphy-handle = <&pcsphy1>, <&pcsphy1>;

This is the sort of reason I wanted to just delete the 10g property.

--Sean

>>  		};
>> 
>>  		enet2: ethernet@e4000 {
>> --
>> 2.35.1.1320.gc452695387.dirty
> 




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux