Hi Krzysztof,
On Tue, 13 Dec 2022 at 18:26, Krzysztof Kozlowski
<krzysztof.kozlowski@xxxxxxxxxx> wrote:
>
> On 13/12/2022 13:38, Bhupesh Sharma wrote:
> > Add USB superspeed qmp phy node to dtsi.
> >
> > Signed-off-by: Bhupesh Sharma <bhupesh.sharma@xxxxxxxxxx>
> > ---
> > arch/arm64/boot/dts/qcom/sm6115.dtsi | 38 ++++++++++++++++++++++++++--
> > 1 file changed, 36 insertions(+), 2 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> > index e4ce135264f3d..9c5c024919f92 100644
> > --- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
> > @@ -579,6 +579,40 @@ usb_hsphy: phy@1613000 {
> > status = "disabled";
> > };
> >
> > + usb_qmpphy: phy@1615000 {
> > + compatible = "qcom,sm6115-qmp-usb3-phy";
> > + reg = <0x01615000 0x200>;
> > + #clock-cells = <1>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
> > + clocks = <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
> > + <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
> > + <&gcc GCC_AHB2PHY_USB_CLK>;
> > + clock-names = "com_aux",
> > + "ref",
> > + "cfg_ahb";
> > + resets = <&gcc GCC_USB3_PHY_PRIM_SP0_BCR>,
> > + <&gcc GCC_USB3PHY_PHY_PRIM_SP0_BCR>;
> > + reset-names = "phy", "phy_phy";
> > + status = "disabled";
>
> Hm, you add a disabled PHY which is used by existing controller. The
> controller is enabled in board DTS, but new PHY node isn't. Aren't you
> now breaking it?
The USB controller is connected to two PHYs - one is HS PHY and the other is SS
QMP Phy. So while the exiting board dts describes and uses only the HS
PHY, newer
board dts files (which will soon be sent out as a separate patch),
will use both the HS and SS
USB PHYs.
So, this will not break the existing board dts files.
> > +
> > + usb_ssphy: phy@1615200 {
> > + reg = <0x01615200 0x200>,
> > + <0x01615400 0x200>,
> > + <0x01615c00 0x400>,
> > + <0x01615600 0x200>,
> > + <0x01615800 0x200>,
> > + <0x01615a00 0x100>;
> > + #phy-cells = <0>;
> > + #clock-cells = <1>;
> > + clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
> > + clock-names = "pipe0";
> > + clock-output-names = "usb3_phy_pipe_clk_src";
> > + };
> > + };
> > +
> > +
>
> Just one blank line.
Ok, Will fix it in v2.
> > qfprom@1b40000 {
> > compatible = "qcom,sm6115-qfprom", "qcom,qfprom";
> > reg = <0x01b40000 0x7000>;
> > @@ -1023,8 +1057,8 @@ usb_dwc3: usb@4e00000 {
> > compatible = "snps,dwc3";
> > reg = <0x04e00000 0xcd00>;
> > interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
> > - phys = <&usb_hsphy>;
> > - phy-names = "usb2-phy";
> > + phys = <&usb_hsphy>, <&usb_ssphy>;
> > + phy-names = "usb2-phy", "usb3-phy";
> > iommus = <&apps_smmu 0x120 0x0>;
> > snps,dis_u2_susphy_quirk;
> > snps,dis_enblslpm_quirk;
>
Thanks,
Bhupesh
