[PATCH v4] arm64: dts: qcom: sa8540p-ride: enable pcie2a node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add the pcie2a, pcie2a_phy, and respective tlmm
nodes that are needed to get pcie 2a controller
enabled on Qdrive3.

This patch enables 4GB 64bit memory space for
PCIE_2A to have BAR allocations of 64bit pref mem
needed on this Qdrive3 platform with dual SoCs
for root port and switch NT-EP. Hence this ranges
property is overridden in sa8540p-ride.dts only.

Signed-off-by: Shazad Hussain <quic_shazhuss@xxxxxxxxxxx>
Reviewed-by: Brian Masney <bmasney@xxxxxxxxxx>
Reported-by: kernel test robot <lkp@xxxxxxxxx>
---
Changes since v3:
- Fix syntax error and add Reported-by (Kernel test robot)

Changes since v2:
- Discard below patch as v3 is merged in qcom tree
  [v4] arm64: dts: qcom: sa8540p-ride: enable PCIe support
  https://lore.kernel.org/all/20221206161916.315640-1-bmasney@xxxxxxxxxx/
- Move tlmm PINCTRL to the end and add R-b (Brian)

Changes since v1:
- Fix ranges property indentation (Konrad)

 arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 96 +++++++++++++++++------
 1 file changed, 71 insertions(+), 25 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
index 6c547f1b13dc..d70859803fbd 100644
--- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
@@ -146,6 +146,27 @@ vreg_l8g: ldo8 {
 	};
 };
 
+&pcie2a {
+	ranges = <0x01000000 0x0 0x3c200000 0x0 0x3c200000 0x0 0x100000>,
+		 <0x02000000 0x0 0x3c300000 0x0 0x3c300000 0x0 0x1d00000>,
+		 <0x03000000 0x5 0x00000000 0x5 0x00000000 0x1 0x00000000>;
+
+	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 145 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie2a_default>;
+
+	status = "okay";
+};
+
+&pcie2a_phy {
+	vdda-phy-supply = <&vreg_l11a>;
+	vdda-pll-supply = <&vreg_l3a>;
+
+	status = "okay";
+};
+
 &pcie3a {
 	ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
 		 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x20000000>,
@@ -186,31 +207,6 @@ &remoteproc_nsp1 {
 	status = "okay";
 };
 
-&tlmm {
-	pcie3a_default: pcie3a-default-state {
-		perst-pins {
-			pins = "gpio151";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-
-		clkreq-pins {
-			pins = "gpio150";
-			function = "pcie3a_clkreq";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-
-		wake-pins {
-			pins = "gpio56";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-up;
-		};
-	};
-};
-
 &ufs_mem_hc {
 	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
 
@@ -268,3 +264,53 @@ &usb_2_qmpphy0 {
 &xo_board_clk {
 	clock-frequency = <38400000>;
 };
+
+/* PINCTRL */
+
+&tlmm {
+	pcie2a_default: pcie2a-default-state {
+		perst-pins {
+			pins = "gpio143";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		clkreq-pins {
+			pins = "gpio142";
+			function = "pcie2a_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		wake-pins {
+			pins = "gpio145";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie3a_default: pcie3a-default-state {
+		perst-pins {
+			pins = "gpio151";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		clkreq-pins {
+			pins = "gpio150";
+			function = "pcie3a_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		wake-pins {
+			pins = "gpio56";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
-- 
2.38.0




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux