On 12.12.2022 12:45, Shazad Hussain wrote: > Add the pcie2a, pcie2a_phy, and respective tlmm > nodes that are needed to get pcie 2a controller > enabled on Qdrive3. > > This patch enables 4GB 64bit memory space for > PCIE_2A to have BAR allocations of 64bit pref mem > needed on this Qdrive3 platform with dual SoCs > for root port and switch NT-EP. Hence this ranges > property is overridden in sa8540p-ride.dts only. > > Signed-off-by: Shazad Hussain <quic_shazhuss@xxxxxxxxxxx> > --- > This patch depends on below patch series for vreg_l11a. > > [v4] arm64: dts: qcom: sa8540p-ride: enable PCIe support > https://lore.kernel.org/all/20221206161916.315640-1-bmasney@xxxxxxxxxx/ > > arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 44 +++++++++++++++++++++++ > 1 file changed, 44 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts > index bb4afd3a9632..ed20423ec8ac 100644 > --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts > +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts > @@ -146,6 +146,27 @@ vreg_l8g: ldo8 { > }; > }; > > +&pcie2a { > + ranges = <0x01000000 0x0 0x3c200000 0x0 0x3c200000 0x0 0x100000>, > + <0x02000000 0x0 0x3c300000 0x0 0x3c300000 0x0 0x1d00000>, > + <0x03000000 0x5 0x00000000 0x5 0x00000000 0x1 0x00000000>; Hi, please fix this indentation. Konrad > + > + perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>; > + wake-gpios = <&tlmm 145 GPIO_ACTIVE_HIGH>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie2a_default>; > + > + status = "okay"; > +}; > + > +&pcie2a_phy { > + vdda-phy-supply = <&vreg_l11a>; > + vdda-pll-supply = <&vreg_l3a>; > + > + status = "okay"; > +}; > + > &pcie3a { > ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, > <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x20000000>, > @@ -247,6 +268,29 @@ &xo_board_clk { > /* PINCTRL */ > > &tlmm { > + pcie2a_default: pcie2a-default-state { > + perst-pins { > + pins = "gpio143"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + clkreq-pins { > + pins = "gpio142"; > + function = "pcie2a_clkreq"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + wake-pins { > + pins = "gpio145"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + }; > + > pcie3a_default: pcie3a-default-state { > perst-pins { > pins = "gpio151";
