On 08/12/2022 04:31, Trevor Wu wrote: > Add mt8188 audio afe document. Use subject prefixes matching the subsystem (git log --oneline -- ...). > > Signed-off-by: Trevor Wu <trevor.wu@xxxxxxxxxxxx> > --- > .../devicetree/bindings/sound/mt8188-afe.yaml | 196 ++++++++++++++++++ > 1 file changed, 196 insertions(+) > create mode 100644 Documentation/devicetree/bindings/sound/mt8188-afe.yaml > > diff --git a/Documentation/devicetree/bindings/sound/mt8188-afe.yaml b/Documentation/devicetree/bindings/sound/mt8188-afe.yaml > new file mode 100644 > index 000000000000..6ab26494d924 > --- /dev/null > +++ b/Documentation/devicetree/bindings/sound/mt8188-afe.yaml This is a friendly reminder during the review process. It seems my previous comments were not fully addressed. Maybe my feedback got lost between the quotes, maybe you just forgot to apply it. Please go back to the previous discussion and either implement all requested changes or keep discussing them. Thank you. Comment was about filename matching compatible, so with vendor prefix. > @@ -0,0 +1,196 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/sound/mt8188-afe.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: MediaTek AFE PCM controller for mt8188 > + > +maintainers: > + - Trevor Wu <trevor.wu@xxxxxxxxxxxx> > + > +properties: > + compatible: > + const: mediatek,mt8188-afe > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + resets: > + maxItems: 1 > + > + reset-names: > + const: audiosys > + > + mediatek,topckgen: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: The phandle of the mediatek topckgen controller > + > + power-domains: > + maxItems: 1 > + > + clocks: > + items: > + - description: 26M clock > + - description: audio pll1 clock > + - description: audio pll2 clock > + - description: clock divider for i2si1_mck > + - description: clock divider for i2si2_mck > + - description: clock divider for i2so1_mck > + - description: clock divider for i2so2_mck > + - description: clock divider for dptx_mck > + - description: a1sys hoping clock > + - description: audio intbus clock > + - description: audio hires clock > + - description: audio local bus clock > + - description: mux for dptx_mck > + - description: mux for i2so1_mck > + - description: mux for i2so2_mck > + - description: mux for i2si1_mck > + - description: mux for i2si2_mck > + - description: audio 26m clock > + > + clock-names: > + items: > + - const: clk26m > + - const: apll1_ck > + - const: apll2_ck > + - const: apll12_div0 > + - const: apll12_div1 > + - const: apll12_div2 > + - const: apll12_div3 > + - const: apll12_div9 > + - const: a1sys_hp_sel > + - const: aud_intbus_sel > + - const: audio_h_sel > + - const: audio_local_bus_sel > + - const: dptx_m_sel > + - const: i2so1_m_sel > + - const: i2so2_m_sel > + - const: i2si1_m_sel > + - const: i2si2_m_sel > + - const: adsp_audio_26m > + > +patternProperties: > + "^mediatek,etdm-in[1-2]-chn-disabled$": > + $ref: /schemas/types.yaml#/definitions/uint8-array > + minItems: 1 > + maxItems: 16 > + description: > + By default, all data received from ETDM pins will be outputed to > + memory. etdm in supports disable_out in direct mode(w/o interconn). > + User can specify the channel ID which they hope dropping and then > + the specified channel won't be seen on memory. So we know what are the IDs but it's a mystery what are the values. Especially with unique values - how any of these should case that channel "won't be seen in memory"? > + uniqueItems: true > + items: > + minimum: 0 > + maximum: 15 > + > + "^mediatek,etdm-in[1-2]-mclk-always-on-rate-hz$": > + description: Specify etdm in mclk output rate for always on case. How is it different than assigned-clock-rates? > + > + "^mediatek,etdm-out[1-3]-mclk-always-on-rate-hz$": > + description: Specify etdm out mclk output rate for always on case. > + > + "^mediatek,etdm-in[1-2]-multi-pin-mode$": > + type: boolean > + description: if present, the etdm data mode is I2S. > + > + "^mediatek,etdm-out[1-3]-multi-pin-mode$": > + type: boolean > + description: if present, the etdm data mode is I2S. > + > + "^mediatek,etdm-in[1-2]-cowork-source$": > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: > + etdm modules can share the same external clock pin. Specify > + which etdm clock source is required by this etdm in moudule. typo: module > + enum: > + - 0 # etdm1_in > + - 1 # etdm2_in > + - 2 # etdm1_out I don't get. This suggests that etdm1_out can be clock source of etdm-in1. Or etdm1_in can be clock source of etdm-in1... It does not make sense... > + - 3 # etdm2_out > + > + "^mediatek,etdm-out[1-2]-cowork-source$": > + $ref: /schemas/types.yaml#/definitions/uint32 > + description: | > + etdm modules can share the same external clock pin. Specify > + which etdm clock source is required by this etdm out moudule. > + enum: > + - 0 # etdm1_in > + - 1 # etdm2_in > + - 2 # etdm1_out > + - 3 # etdm2_out > + > +required: > + - compatible > + - reg > + - interrupts > + - resets > + - reset-names > + - mediatek,topckgen > + - power-domains > + - clocks > + - clock-names > + Best regards, Krzysztof
