From: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
The SC8280XP CRD has a EDP display on MDSS0 DP3, enable relevant nodes
and link it together with the backlight control.
Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
Signed-off-by: Bjorn Andersson <quic_bjorande@xxxxxxxxxxx>
---
Changes since v4:
- None
arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 72 ++++++++++++++++++++++-
1 file changed, 71 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
index f09810e3d956..a7d2384cbbe8 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
@@ -20,7 +20,7 @@ aliases {
serial0 = &qup2_uart17;
};
- backlight {
+ backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pmc8280c_lpg 3 1000000>;
enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
@@ -34,6 +34,22 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ vreg_edp_3p3: regulator-edp-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_EDP_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_reg_en>;
+
+ regulator-boot-on;
+ };
+
vreg_edp_bl: regulator-edp-bl {
compatible = "regulator-fixed";
@@ -230,6 +246,54 @@ vreg_l9d: ldo9 {
};
};
+&dispcc0 {
+ status = "okay";
+};
+
+&mdss0 {
+ status = "okay";
+};
+
+&mdss0_dp3 {
+ compatible = "qcom,sc8280xp-edp";
+ status = "okay";
+
+ data-lanes = <0 1 2 3>;
+
+ aux-bus {
+ panel {
+ compatible = "edp-panel";
+ power-supply = <&vreg_edp_3p3>;
+
+ backlight = <&backlight>;
+
+ ports {
+ port {
+ edp_panel_in: endpoint {
+ remote-endpoint = <&mdss0_dp3_out>;
+ };
+ };
+ };
+ };
+ };
+
+ ports {
+ port@1 {
+ reg = <1>;
+ mdss0_dp3_out: endpoint {
+ remote-endpoint = <&edp_panel_in>;
+ };
+ };
+ };
+};
+
+&mdss0_dp3_phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l6b>;
+ vdda-pll-supply = <&vreg_l3b>;
+};
+
&pcie2a {
perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
@@ -496,6 +560,12 @@ hastings_reg_en: hastings-reg-en-state {
&tlmm {
gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
+ edp_reg_en: edp-reg-en-state {
+ pins = "gpio25";
+ function = "gpio";
+ output-enable;
+ };
+
kybd_default: kybd-default-state {
disable-pins {
pins = "gpio102";
--
2.37.3
