This I2C module is integrated into the Loongson-2K SoCs and Loongson
LS7A bridge chip.
Signed-off-by: Binbin Zhou <zhoubinbin@xxxxxxxxxxx>
---
drivers/i2c/busses/Kconfig | 11 +
drivers/i2c/busses/Makefile | 1 +
drivers/i2c/busses/i2c-ls2x.c | 379 ++++++++++++++++++++++++++++++++++
3 files changed, 391 insertions(+)
create mode 100644 drivers/i2c/busses/i2c-ls2x.c
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index e50f9603d189..908096a762ca 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -888,6 +888,17 @@ config I2C_OWL
Say Y here if you want to use the I2C bus controller on
the Actions Semiconductor Owl SoC's.
+config I2C_LS2X
+ tristate "Loongson LS2X I2C adapter"
+ depends on MACH_LOONGSON64 || COMPILE_TEST
+ help
+ If you say yes to this option, support will be included for the
+ I2C interface on the Loongson-2K SoCs and Loongson LS7A bridge
+ chip.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-ls2x.
+
config I2C_PASEMI
tristate "PA Semi SMBus interface"
depends on PPC_PASEMI && PCI
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index e73cdb1d2b5a..df332ec3c489 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -86,6 +86,7 @@ obj-$(CONFIG_I2C_MV64XXX) += i2c-mv64xxx.o
obj-$(CONFIG_I2C_MXS) += i2c-mxs.o
obj-$(CONFIG_I2C_NOMADIK) += i2c-nomadik.o
obj-$(CONFIG_I2C_NPCM) += i2c-npcm7xx.o
+obj-$(CONFIG_I2C_LS2X) += i2c-ls2x.o
obj-$(CONFIG_I2C_OCORES) += i2c-ocores.o
obj-$(CONFIG_I2C_OMAP) += i2c-omap.o
obj-$(CONFIG_I2C_OWL) += i2c-owl.o
diff --git a/drivers/i2c/busses/i2c-ls2x.c b/drivers/i2c/busses/i2c-ls2x.c
new file mode 100644
index 000000000000..788296380118
--- /dev/null
+++ b/drivers/i2c/busses/i2c-ls2x.c
@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Loongson-2K/Loongson LS7A I2C master mode driver
+ *
+ * Copyright (C) 2013 Loongson Technology Corporation Limited.
+ * Copyright (C) 2014-2017 Lemote, Inc.
+ * Copyright (C) 2018-2022 Loongson Technology Corporation Limited.
+ *
+ * Originally written by liushaozong
+ *
+ * Rewritten for mainline by Binbin Zhou <zhoubinbin@xxxxxxxxxxx>
+ */
+
+#include <linux/bits.h>
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/platform_device.h>
+#include <linux/units.h>
+
+/* I2C Registers */
+#define I2C_LS2X_PRER_LO 0x0 /* Freq Division Low Byte Register */
+#define I2C_LS2X_PRER_HI 0x1 /* Freq Division High Byte Register */
+#define I2C_LS2X_CTR 0x2 /* Control Register */
+#define I2C_LS2X_TXR 0x3 /* Transport Data Register */
+#define I2C_LS2X_RXR 0x3 /* Receive Data Register */
+#define I2C_LS2X_CR 0x4 /* Command Control Register */
+#define I2C_LS2X_SR 0x4 /* State Register */
+
+/* Command Control Register Bit */
+#define LS2X_CR_START BIT(7) /* Start signal */
+#define LS2X_CR_STOP BIT(6) /* Stop signal */
+#define LS2X_CR_READ BIT(5) /* Read signal */
+#define LS2X_CR_WRITE BIT(4) /* Write signal */
+#define LS2X_CR_ACK BIT(3) /* Response signal */
+#define LS2X_CR_IACK BIT(0) /* Interrupt response signal */
+
+/* State Register Bit */
+#define LS2X_SR_NOACK BIT(7) /* Receive NACK */
+#define LS2X_SR_BUSY BIT(6) /* Bus busy state */
+#define LS2X_SR_AL BIT(5) /* Arbitration lost */
+#define LS2X_SR_TIP BIT(1) /* Transmission state */
+#define LS2X_SR_IF BIT(0) /* Interrupt flag */
+
+/* Control Register Bit */
+#define LS2X_CTR_EN BIT(7) /* 0: I2c frequency setting 1: Normal */
+#define LS2X_CTR_IEN BIT(6) /* Enable i2c interrupt */
+#define LS2X_CTR_MST BIT(5) /* 0: Slave mode 1: Master mode */
+
+struct ls2x_i2c_priv {
+ struct i2c_adapter adapter;
+ struct device *dev;
+ void __iomem *base;
+ struct i2c_timings i2c_t;
+ struct completion cmd_complete;
+ unsigned int suspended:1;
+};
+
+static int ls2x_i2c_xfer_byte(struct i2c_adapter *adap, u8 txdata, u8 *rxdatap)
+{
+ u8 rxdata;
+ unsigned long time_left;
+ struct ls2x_i2c_priv *priv = i2c_get_adapdata(adap);
+
+ writeb(txdata, priv->base + I2C_LS2X_CR);
+
+ time_left = wait_for_completion_timeout(&priv->cmd_complete,
+ adap->timeout);
+ if (!time_left) {
+ dev_err(&adap->dev, "transaction timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ rxdata = readb(priv->base + I2C_LS2X_SR);
+ if (rxdatap)
+ *rxdatap = rxdata;
+
+ return 0;
+}
+
+static int ls2x_i2c_send_byte(struct i2c_adapter *adap, u8 txdata)
+{
+ int ret;
+ u8 rxdata;
+
+ ret = ls2x_i2c_xfer_byte(adap, txdata, &rxdata);
+ if (ret)
+ return ret;
+
+ if (rxdata & LS2X_SR_NOACK)
+ return -ENXIO;
+
+ return 0;
+}
+
+static int ls2x_i2c_stop(struct i2c_adapter *adap)
+{
+ int ret = ls2x_i2c_send_byte(adap, LS2X_CR_STOP);
+
+ return (ret == -ENXIO) ? 0 : ret;
+}
+
+static int ls2x_i2c_start(struct i2c_adapter *adap, struct i2c_msg *msgs)
+{
+ struct ls2x_i2c_priv *priv = i2c_get_adapdata(adap);
+
+ reinit_completion(&priv->cmd_complete);
+
+ writeb(i2c_8bit_addr_from_msg(msgs), priv->base + I2C_LS2X_TXR);
+ return ls2x_i2c_send_byte(adap, (LS2X_CR_START | LS2X_CR_WRITE));
+}
+
+static int ls2x_i2c_rx(struct i2c_adapter *adap, u8 *buf, u16 len)
+{
+ unsigned long time_left;
+ int cmd = LS2X_CR_READ;
+ struct ls2x_i2c_priv *priv = i2c_get_adapdata(adap);
+
+ while (len--) {
+ writeb(cmd | (len ? 0 : LS2X_CR_ACK), priv->base + I2C_LS2X_CR);
+
+ time_left = wait_for_completion_timeout(&priv->cmd_complete,
+ adap->timeout);
+ if (unlikely(!time_left)) {
+ dev_err(priv->dev, "transaction timeout\n");
+ return -ETIMEDOUT;
+ }
+
+ *buf++ = readb(priv->base + I2C_LS2X_RXR);
+ }
+
+ return 0;
+}
+
+static int ls2x_i2c_tx(struct i2c_adapter *adap, u8 *buf, u16 len)
+{
+ int ret;
+ struct ls2x_i2c_priv *priv = i2c_get_adapdata(adap);
+
+ while (len--) {
+ writeb(*buf++, priv->base + I2C_LS2X_TXR);
+
+ ret = ls2x_i2c_send_byte(adap, LS2X_CR_WRITE);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int ls2x_i2c_xfer_one(struct i2c_adapter *adap,
+ struct i2c_msg *msg, bool stop)
+{
+ int ret;
+ bool is_read = msg->flags & I2C_M_RD;
+
+ /* Contains steps to send start condition and address */
+ ret = ls2x_i2c_start(adap, msg);
+ if (ret)
+ return ret;
+
+ if (is_read)
+ ret = ls2x_i2c_rx(adap, msg->buf, msg->len);
+ else
+ ret = ls2x_i2c_tx(adap, msg->buf, msg->len);
+
+ /* could not acquire bus. bail out without STOP */
+ if (ret == -EAGAIN)
+ return ret;
+
+ if (stop)
+ ret = ls2x_i2c_stop(adap);
+
+ return ret;
+}
+
+static int ls2x_i2c_master_xfer(struct i2c_adapter *adap,
+ struct i2c_msg *msgs, int num)
+{
+ int ret;
+ struct i2c_msg *msg, *emsg = msgs + num;
+
+ for (msg = msgs; msg < emsg; msg++) {
+ /* Emit STOP if it is the last message or I2C_M_STOP is set */
+ bool stop = (msg + 1 == emsg) || (msg->flags & I2C_M_STOP);
+
+ ret = ls2x_i2c_xfer_one(adap, msg, stop);
+ if (ret)
+ return ret;
+ }
+
+ return num;
+}
+
+static unsigned int ls2x_i2c_func(struct i2c_adapter *adap)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static const struct i2c_algorithm ls2x_i2c_algo = {
+ .master_xfer = ls2x_i2c_master_xfer,
+ .functionality = ls2x_i2c_func,
+};
+
+/*
+ * Interrupt service routine.
+ * This gets called whenever an I2C interrupt occurs.
+ */
+static irqreturn_t ls2x_i2c_irq_handler(int this_irq, void *dev_id)
+{
+ struct ls2x_i2c_priv *priv = dev_id;
+
+ if (!(readb(priv->base + I2C_LS2X_SR) & LS2X_SR_IF))
+ return IRQ_NONE;
+
+ writeb(LS2X_CR_IACK, priv->base + I2C_LS2X_CR);
+ complete(&priv->cmd_complete);
+ return IRQ_HANDLED;
+}
+
+/*
+ * The I2C controller has a fixed I2C bus frequency by default, but to
+ * be compatible with more client devices, we can obtain the set I2C
+ * bus frequency from ACPI or FDT.
+ */
+static void ls2x_i2c_adjust_bus_speed(struct ls2x_i2c_priv *priv)
+{
+ u16 val = 0x12c; /* Default value of I2C divider latch register */
+ struct i2c_timings *t = &priv->i2c_t;
+ u32 acpi_speed = i2c_acpi_find_bus_speed(priv->dev);
+
+ i2c_parse_fw_timings(priv->dev, t, false);
+
+ if (acpi_speed || t->bus_freq_hz)
+ val = 10 * HZ_PER_MHZ / max(t->bus_freq_hz, acpi_speed) - 1;
+
+ /* Set LS2X I2C frequency */
+ writel(val, priv->base + I2C_LS2X_PRER_LO);
+}
+
+static void ls2x_i2c_reginit(struct ls2x_i2c_priv *priv)
+{
+ u8 data;
+
+ /* Enable operations about frequency divider register */
+ data = readb(priv->base + I2C_LS2X_CTR);
+ writeb(data & ~LS2X_CTR_EN, priv->base + I2C_LS2X_CTR);
+
+ ls2x_i2c_adjust_bus_speed(priv);
+
+ /* Set to normal I2C operating mode and enable interrupts */
+ data = readb(priv->base + I2C_LS2X_CTR);
+ writeb(data | LS2X_CTR_EN | LS2X_CTR_IEN | LS2X_CTR_MST,
+ priv->base + I2C_LS2X_CTR);
+}
+
+static int ls2x_i2c_probe(struct platform_device *pdev)
+{
+ int r, irq;
+ struct i2c_adapter *adap;
+ struct ls2x_i2c_priv *priv;
+ struct device *dev = &pdev->dev;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ /* Map hardware registers */
+ priv->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ r = devm_request_irq(dev, irq, ls2x_i2c_irq_handler,
+ IRQF_SHARED, "ls2x-i2c", priv);
+ if (r < 0)
+ return dev_err_probe(dev, r, "Unable to request irq %d\n", irq);
+
+ /* Add the i2c adapter */
+ adap = &priv->adapter;
+ adap->nr = pdev->id;
+ adap->owner = THIS_MODULE;
+ adap->retries = 5;
+ adap->algo = &ls2x_i2c_algo;
+ adap->dev.parent = dev;
+ device_set_node(&adap->dev, dev_fwnode(dev));
+ i2c_set_adapdata(adap, priv);
+ strscpy(adap->name, pdev->name, sizeof(adap->name));
+ init_completion(&priv->cmd_complete);
+
+ priv->dev = dev;
+ platform_set_drvdata(pdev, priv);
+
+ ls2x_i2c_reginit(priv);
+
+ r = devm_i2c_add_adapter(dev, adap);
+ if (r)
+ return dev_err_probe(dev, r, "Failure adding adapter\n");
+
+ return 0;
+}
+
+static int ls2x_i2c_remove(struct platform_device *pdev)
+{
+ struct ls2x_i2c_priv *priv = platform_get_drvdata(pdev);
+
+ i2c_del_adapter(&priv->adapter);
+ return 0;
+}
+
+static int ls2x_i2c_suspend(struct device *dev)
+{
+ struct ls2x_i2c_priv *priv = dev_get_drvdata(dev);
+
+ priv->suspended = 1;
+ return 0;
+}
+
+static int ls2x_i2c_resume(struct device *dev)
+{
+ struct ls2x_i2c_priv *priv = dev_get_drvdata(dev);
+
+ priv->suspended = 0;
+ ls2x_i2c_reginit(priv);
+ return 0;
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(ls2x_i2c_pm_ops,
+ ls2x_i2c_suspend, ls2x_i2c_resume, NULL);
+
+static const struct of_device_id ls2x_i2c_id_table[] = {
+ { .compatible = "loongson,ls2k-i2c" },
+ { .compatible = "loongson,ls7a-i2c" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, ls2x_i2c_id_table);
+
+static const struct acpi_device_id ls2x_i2c_acpi_match[] = {
+ { "LOON0004" },
+ { }
+};
+MODULE_DEVICE_TABLE(acpi, ls2x_i2c_acpi_match);
+
+static struct platform_driver ls2x_i2c_driver = {
+ .probe = ls2x_i2c_probe,
+ .remove = ls2x_i2c_remove,
+ .driver = {
+ .name = "ls2x-i2c",
+ .pm = pm_sleep_ptr(&ls2x_i2c_pm_ops),
+ .of_match_table = ls2x_i2c_id_table,
+ .acpi_match_table = ls2x_i2c_acpi_match,
+ },
+};
+
+static int __init ls2x_i2c_init_driver(void)
+{
+ return platform_driver_register(&ls2x_i2c_driver);
+}
+subsys_initcall(ls2x_i2c_init_driver);
+
+static void __exit ls2x_i2c_exit_driver(void)
+{
+ platform_driver_unregister(&ls2x_i2c_driver);
+}
+module_exit(ls2x_i2c_exit_driver);
+
+MODULE_DESCRIPTION("Loongson LS2X I2C Bus driver");
+MODULE_AUTHOR("Loongson Technology Corporation Limited");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:ls2x-i2c");
--
2.31.1
