On 01/12/2022 23:57, Dmitry Rokosov wrote:
> This patch adds clkc_periphs and clkc_pll dts nodes to A1 SoC main dtsi.
> The first one clk controller is responsible for all SoC peripherals
> clocks excluding audio clocks. The second one clk controller is used by
> A1 SoC PLLs. Actually, there are two different APB heads, so we have two
> different drivers.
>
> Signed-off-by: Dmitry Rokosov <ddrokosov@xxxxxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/amlogic/meson-a1.dtsi | 27 ++++++++++++++++++++++-
> 1 file changed, 26 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> index b4000cf65a9a..38e6517c603c 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-a1.dtsi
> @@ -6,6 +6,8 @@
> #include <dt-bindings/interrupt-controller/irq.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/gpio/meson-a1-gpio.h>
> +#include <dt-bindings/clock/a1-pll-clkc.h>
> +#include <dt-bindings/clock/a1-clkc.h>
>
> / {
> compatible = "amlogic,a1";
> @@ -81,7 +83,6 @@ apb: bus@fe000000 {
> #size-cells = <2>;
> ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x1000000>;
>
> -
> reset: reset-controller@0 {
> compatible = "amlogic,meson-a1-reset";
> reg = <0x0 0x0 0x0 0x8c>;
> @@ -124,6 +125,30 @@ uart_AO_B: serial@2000 {
> clock-names = "xtal", "pclk", "baud";
> status = "disabled";
> };
> +
> + clkc_periphs: periphs-clock-controller@800 {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "amlogic,a1-periphs-clkc";
> + reg = <0 0x800 0 0x104>;
> + #clock-cells = <1>;
> + clocks = <&clkc_pll CLKID_FCLK_DIV2>,
> + <&clkc_pll CLKID_FCLK_DIV3>,
> + <&clkc_pll CLKID_FCLK_DIV5>,
> + <&clkc_pll CLKID_FCLK_DIV7>,
> + <&clkc_pll CLKID_HIFI_PLL>,
> + <&xtal>;
> + clock-names = "fclk_div2", "fclk_div3",
> + "fclk_div5", "fclk_div7",
> + "hifi_pll", "xtal";
> + };
> +
> + clkc_pll: pll-clock-controller@7c80 {
Node names should be generic.
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
> + compatible = "amlogic,a1-pll-clkc";
Best regards,
Krzysztof
