The sc7180 phy compatible works fine for some cases, but it turns out sm6350 does need proper phy configuration in the driver, so use the newly added sm6350 compatible. Because the sm6350 compatible is using the new binding, we need to change the node quite a bit to match it. This fixes qmpphy init when no USB cable is plugged in during bootloader stage. Signed-off-by: Luca Weiss <luca.weiss@xxxxxxxxxxxxx> --- Changes since v2: * Rebase on https://lore.kernel.org/all/20221111094729.11842-2-johan+linaro@xxxxxxxxxx/ While this commit deletes the changes there it's still good to get it in for completeness * Fix clocks, add power-domain arch/arm64/boot/dts/qcom/sm6350.dtsi | 50 ++++++++-------------------- 1 file changed, 14 insertions(+), 36 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi index 43324bf291c3..cb48f03a6cc9 100644 --- a/arch/arm64/boot/dts/qcom/sm6350.dtsi +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi @@ -11,6 +11,7 @@ #include <dt-bindings/interconnect/qcom,sm6350.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/mailbox/qcom-ipcc.h> +#include <dt-bindings/phy/phy-qcom-qmp.h> #include <dt-bindings/power/qcom-rpmpd.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> @@ -1119,49 +1120,26 @@ usb_1_hsphy: phy@88e3000 { resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; }; - usb_1_qmpphy: phy@88e9000 { - compatible = "qcom,sc7180-qmp-usb3-dp-phy"; - reg = <0 0x088e9000 0 0x200>, - <0 0x088e8000 0 0x40>, - <0 0x088ea000 0 0x200>; - status = "disabled"; - #address-cells = <2>; - #size-cells = <2>; - ranges; + usb_1_qmpphy: phy@88e8000 { + compatible = "qcom,sm6350-qmp-usb3-dp-phy"; + reg = <0 0x088e8000 0 0x3000>; clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, - <&xo_board>, - <&rpmhcc RPMH_QLINK_CLK>, - <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>; - clock-names = "aux", "cfg_ahb", "ref", "com_aux"; + <&gcc GCC_USB3_PRIM_CLKREF_CLK>, + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>, + <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; + clock-names = "aux", "ref", "com_aux", "usb3_pipe"; + + power-domains = <&gcc USB30_PRIM_GDSC>; resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>, <&gcc GCC_USB3_PHY_PRIM_BCR>; reset-names = "phy", "common"; - usb_1_ssphy: usb3-phy@88e9200 { - reg = <0 0x088e9200 0 0x200>, - <0 0x088e9400 0 0x200>, - <0 0x088e9c00 0 0x400>, - <0 0x088e9600 0 0x200>, - <0 0x088e9800 0 0x200>, - <0 0x088e9a00 0 0x100>; - #clock-cells = <0>; - #phy-cells = <0>; - clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; - clock-names = "pipe0"; - clock-output-names = "usb3_phy_pipe_clk_src"; - }; + #clock-cells = <1>; + #phy-cells = <1>; - dp_phy: dp-phy@88ea200 { - reg = <0 0x088ea200 0 0x200>, - <0 0x088ea400 0 0x200>, - <0 0x088eaa00 0 0x200>, - <0 0x088ea600 0 0x200>, - <0 0x088ea800 0 0x200>; - #phy-cells = <0>; - #clock-cells = <1>; - }; + status = "disabled"; }; dc_noc: interconnect@9160000 { @@ -1235,7 +1213,7 @@ usb_1_dwc3: usb@a600000 { snps,dis_enblslpm_quirk; snps,has-lpm-erratum; snps,hird-threshold = /bits/ 8 <0x10>; - phys = <&usb_1_hsphy>, <&usb_1_ssphy>; + phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>; phy-names = "usb2-phy", "usb3-phy"; }; }; -- 2.38.1
