From: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
Add nodes for PM8550vs in separate dtsi file.
Signed-off-by: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/pm8550vs.dtsi | 194 +++++++++++++++++++++++++
1 file changed, 194 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm8550vs.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm8550vs.dtsi b/arch/arm64/boot/dts/qcom/pm8550vs.dtsi
new file mode 100644
index 000000000000..97b1c18aa7d8
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8550vs.dtsi
@@ -0,0 +1,194 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pm8550vs-c-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pm8550vs_c_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550vs-d-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pm8550vs_d_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550vs-e-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pm8550vs_e_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pm8550vs-g-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pm8550vs_g_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+ };
+};
+
+
+&spmi_bus {
+ pm8550vs_c: pmic@2 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x2 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550vs_c_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550vs_c_gpios: gpio@8800 {
+ compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550vs_c_gpios 0 0 6>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8550vs_d: pmic@3 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x3 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550vs_d_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550vs_d_gpios: gpio@8800 {
+ compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550vs_d_gpios 0 0 6>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8550vs_e: pmic@4 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550vs_e_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550vs_e_gpios: gpio@8800 {
+ compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550vs_e_gpios 0 0 6>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pm8550vs_g: pmic@6 {
+ compatible = "qcom,pm8550", "qcom,spmi-pmic";
+ reg = <0x6 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8550vs_g_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0x6 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8550vs_g_gpios: gpio@8800 {
+ compatible = "qcom,pm8550vs-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pm8550vs_g_gpios 0 0 6>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
--
2.34.1
