Re: [PATCH 5/7] riscv: dts: bouffalolab: add the bl808 SoC base device tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, 21 Nov 2022 at 04:37, Icenowy Zheng <uwu@xxxxxxxxxx> wrote:
>
> 在 2022-11-20星期日的 15:57 +0100,Emil Renner Berthing写道:
> > On Sun, 20 Nov 2022 at 09:32, Jisheng Zhang <jszhang@xxxxxxxxxx>
> > wrote:
> > >
> > > Add a baisc dtsi for the bouffalolab bl808 SoC.
> > >
> > > Signed-off-by: Jisheng Zhang <jszhang@xxxxxxxxxx>
> > > ---
> > >  arch/riscv/boot/dts/Makefile               |  1 +
> > >  arch/riscv/boot/dts/bouffalolab/bl808.dtsi | 74
> > > ++++++++++++++++++++++
> > >  2 files changed, 75 insertions(+)
> > >  create mode 100644 arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> > >
> > > diff --git a/arch/riscv/boot/dts/Makefile
> > > b/arch/riscv/boot/dts/Makefile
> > > index ff174996cdfd..b525467152b2 100644
> > > --- a/arch/riscv/boot/dts/Makefile
> > > +++ b/arch/riscv/boot/dts/Makefile
> > > @@ -1,4 +1,5 @@
> > >  # SPDX-License-Identifier: GPL-2.0
> > > +subdir-y += bouffalolab
> > >  subdir-y += sifive
> > >  subdir-y += starfive
> > >  subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> > > diff --git a/arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> > > b/arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> > > new file mode 100644
> > > index 000000000000..c98ebb14ee10
> > > --- /dev/null
> > > +++ b/arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> > > @@ -0,0 +1,74 @@
> > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> > > +/*
> > > + * Copyright (C) 2022 Jisheng Zhang <jszhang@xxxxxxxxxx>
> > > + */
> > > +
> > > +#include <dt-bindings/interrupt-controller/irq.h>
> > > +
> > > +/ {
> > > +       compatible = "bouffalolab,bl808";
> > > +       #address-cells = <1>;
> > > +       #size-cells = <1>;
> > > +
> > > +       cpus {
> > > +               timebase-frequency = <1000000>;
> > > +               #address-cells = <1>;
> > > +               #size-cells = <0>;
> > > +
> > > +               cpu0: cpu@0 {
> > > +                       compatible = "thead,c906", "riscv";
> > > +                       device_type = "cpu";
> > > +                       reg = <0>;
> > > +                       d-cache-block-size = <64>;
> > > +                       d-cache-sets = <256>;
> > > +                       d-cache-size = <32768>;
> > > +                       i-cache-block-size = <64>;
> > > +                       i-cache-sets = <128>;
> > > +                       i-cache-size = <32768>;
> > > +                       mmu-type = "riscv,sv39";
> > > +                       riscv,isa = "rv64imafdc";
> > > +
> > > +                       cpu0_intc: interrupt-controller {
> > > +                               compatible = "riscv,cpu-intc";
> > > +                               interrupt-controller;
> > > +                               #address-cells = <0>;
> > > +                               #interrupt-cells = <1>;
> > > +                       };
> > > +               };
> > > +       };
> > > +
> > > +       xtal: xtal-clk {
> > > +               compatible = "fixed-clock";
> > > +               clock-frequency = <40000000>;
> >
> > This was discussed many times before, but I think the conclusion was
> > that the frequency is a property of the crystal on the board, so this
> > should be 0 in the SoC dtsi, and then overwritten in the board device
> > tree.
>
> But many chips just specify an accepted frequency in their datasheet,
> and using a frequency other than this is undefined behavior.

Yes, this was the argument in previous discussions, but the conclusion
was still that it should go in the board dts. To be clear I'm just
summing up the conclusion from previous discussions about this, and
have no strong opinion other than we should do the same everywhere.

> >
> > > +               clock-output-names = "xtal";
> > > +               #clock-cells = <0>;
> > > +       };
> > > +
> > > +       soc {
> > > +               compatible = "simple-bus";
> > > +               ranges;
> > > +               interrupt-parent = <&plic>;
> > > +               dma-noncoherent;
> > > +               #address-cells = <1>;
> > > +               #size-cells = <1>;
> > > +
> > > +               uart0: serial@30002000 {
> > > +                       compatible = "bouffalolab,uart";
> > > +                       reg = <0x30002000 0x1000>;
> > > +                       interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
> > > +                       clocks = <&xtal>;
> > > +                       status = "disabled";
> > > +               };
> > > +
> > > +               plic: interrupt-controller@e0000000 {
> > > +                       compatible = "thead,c900-plic";
> > > +                       reg = <0xe0000000 0x4000000>;
> > > +                       interrupts-extended = <&cpu0_intc
> > > 0xffffffff>,
> > > +                                             <&cpu0_intc 9>;
> > > +                       interrupt-controller;
> > > +                       #address-cells = <0>;
> > > +                       #interrupt-cells = <2>;
> > > +                       riscv,ndev = <64>;
> > > +               };
> > > +       };
> > > +};
> > > --
> > > 2.37.2
> > >
> > >
> > > _______________________________________________
> > > linux-riscv mailing list
> > > linux-riscv@xxxxxxxxxxxxxxxxxxx
> > > http://lists.infradead.org/mailman/listinfo/linux-riscv
> >
> > _______________________________________________
> > linux-riscv mailing list
> > linux-riscv@xxxxxxxxxxxxxxxxxxx
> > http://lists.infradead.org/mailman/listinfo/linux-riscv
>




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux