From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx> Add support for Bananapi R3 SBC. - SD/eMMC support (switching first 4 bits of data-bus with sw6/D) - all rj45 ports and both SFP working (eth1/lan4) - all USB-Ports + SIM-Slot tested - i2c and all uarts tested - wifi tested (with eeprom calibration data) Signed-off-by: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx> --- The device can boot from all 4 storage options. Both, SPI and MMC, can be switched using hardware switches on the board, see https://wiki.banana-pi.org/Banana_Pi_BPI-R3#Jumper_setting I have added base dtb for sd/emmc to have a bootable version in mainline linux. SPI-NAND/NOR switched (CS by sw5/C) can be done with DT-Overlays, but don't know how to do it in upstream the right way...added dts files for dtbo and added them with dtbo extension to Makefile works. there is a commit which adds support building dtso files to dtbo in next: "kbuild: Allow DTB overlays to built from .dtso named source files" https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2 if Overlays are accepted then we can change my current dts from here to overlays too to have all as such. Till then imho the best way is to have mmc as board dts and add the right spi-device via overlay if needed. changes: v6: - drop usb 5v regulator from bpi-r3 based on chunfengs response it is only needed if regulator is switched (like for otg), usb works without it. v4: - add PCIe nodes - fix sfp-properties of sfp-1 (need to be plural) thx to Denis Odintsov for this v3: - rename factory-key to reset-key - add dcin regulator and add it as input for 3v3 (with renaming) - remove memory-node - dropped wifi eeprom (calibration) data - move mmc0 pinctrl to common dtsi and drop sdcard comment - change mmc pull-up/down to have generic bias-pull* v2: - remove pcie to be added later (discussion about clocks) - some fixes based on suggestions on ML - add key suffix like it's done in mt7622-bpi-r64 devicetree - add dash in sfp node names - use reg as unit for switch-node - drop "-3-4" suffix from i2c-pins node name - fix order in Makefile --- arch/arm64/boot/dts/mediatek/Makefile | 2 + .../mediatek/mt7986a-bananapi-bpi-r3-emmc.dts | 31 ++ .../mediatek/mt7986a-bananapi-bpi-r3-sd.dts | 25 + .../dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi | 446 ++++++++++++++++++ 4 files changed, 504 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index 0ec90cb3ef28..e8902f2cc58f 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -7,6 +7,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts new file mode 100644 index 000000000000..a0ca35b5977e --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-emmc.dts @@ -0,0 +1,31 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Author: Sam.Shih <sam.shih@xxxxxxxxxxxx> + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> + +#include "mt7986a-bananapi-bpi-r3.dtsi" + +/ { + model = "Bananapi BPI-R3 (emmc)"; +}; + +&mmc0 { + bus-width = <8>; + max-frequency = <200000000>; + cap-mmc-highspeed; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + hs400-ds-delay = <0x14014>; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_1p8v>; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts new file mode 100644 index 000000000000..06e4691cb815 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-sd.dts @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Author: Sam.Shih <sam.shih@xxxxxxxxxxxx> + */ + +/dts-v1/; +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> + +#include "mt7986a-bananapi-bpi-r3.dtsi" + +/ { + model = "Bananapi BPI-R3 (sdmmc)"; +}; + +&mmc0 { + bus-width = <4>; + max-frequency = <52000000>; + cap-sd-highspeed; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_1p8v>; + status = "okay"; +}; + diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi new file mode 100644 index 000000000000..455e958ea08a --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3.dtsi @@ -0,0 +1,446 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Authors: Sam.Shih <sam.shih@xxxxxxxxxxxx> + * Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx> + * Daniel Golle <daniel@xxxxxxxxxxxxxx> + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/mt65xx.h> + +#include "mt7986a.dtsi" + +/ { + model = "Bananapi BPI-R3"; + compatible = "bananapi,bpi-r3", "mediatek,mt7986a"; + + aliases { + serial0 = &uart0; + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + dcin: regulator-12vd { + compatible = "regulator-fixed"; + regulator-name = "12vd"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-boot-on; + regulator-always-on; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset-key { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + wps-key { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + }; + }; + + /* i2c of the left SFP cage (wan) */ + i2c_sfp1: i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&pio 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&pio 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + /* i2c of the right SFP cage (lan) */ + i2c_sfp2: i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&pio 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&pio 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + leds { + compatible = "gpio-leds"; + + green_led: led-0 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_POWER; + gpios = <&pio 69 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + blue_led: led-1 { + color = <LED_COLOR_ID_BLUE>; + function = LED_FUNCTION_STATUS; + gpios = <&pio 86 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1.8vd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <&dcin>; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3.3vd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <&dcin>; + }; + + /* left SFP cage (wan) */ + sfp1: sfp-1 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + los-gpios = <&pio 46 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 49 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 20 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 7 GPIO_ACTIVE_HIGH>; + }; + + /* right SFP cage (lan) */ + sfp2: sfp-2 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + los-gpios = <&pio 31 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 47 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 15 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 48 GPIO_ACTIVE_HIGH>; + }; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "2500base-x"; + sfp = <&sfp1>; + managed = "in-band-status"; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + }; +}; + +&mdio { + switch: switch@31 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + }; +}; + +&mmc0 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins>; + status = "okay"; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_pins>; + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + +&pio { + i2c_pins: i2c-pins { + mux { + function = "i2c"; + groups = "i2c"; + }; + }; + + mmc0_pins_default: mmc0-pins { + mux { + function = "emmc"; + groups = "emmc_51"; + }; + conf-cmd-dat { + pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", + "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", + "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; + input-enable; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + conf-clk { + pins = "EMMC_CK"; + drive-strength = <6>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-ds { + pins = "EMMC_DSL"; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-rst { + pins = "EMMC_RSTB"; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + }; + + mmc0_pins_uhs: mmc0-uhs-pins { + mux { + function = "emmc"; + groups = "emmc_51"; + }; + conf-cmd-dat { + pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", + "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", + "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; + input-enable; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + conf-clk { + pins = "EMMC_CK"; + drive-strength = <6>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-ds { + pins = "EMMC_DSL"; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-rst { + pins = "EMMC_RSTB"; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + }; + + pcie_pins: pcie-pins { + mux { + function = "pcie"; + groups = "pcie_clk", "pcie_pereset"; + }; + }; + + spi_flash_pins: spi-flash-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + }; + + spic_pins: spic-pins { + mux { + function = "spi"; + groups = "spi1_0"; + }; + }; + + uart1_pins: uart1-pins { + mux { + function = "uart"; + groups = "uart1_rx_tx"; + }; + }; + + uart2_pins: uart2-pins { + mux { + function = "uart"; + groups = "uart2_0_rx_tx"; + }; + }; + + wf_2g_5g_pins: wf-2g-5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + wf_dbdc_pins: wf-dbdc-pins { + mux { + function = "wifi"; + groups = "wf_dbdc"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + wf_led_pins: wf-led-pins { + mux { + function = "led"; + groups = "wifi_led"; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + cs-gpios = <0>, <0>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spic_pins>; + cs-gpios = <0>, <0>; + status = "okay"; +}; + +&ssusb { + status = "okay"; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "wan"; + }; + + port@1 { + reg = <1>; + label = "lan0"; + }; + + port@2 { + reg = <2>; + label = "lan1"; + }; + + port@3 { + reg = <3>; + label = "lan2"; + }; + + port@4 { + reg = <4>; + label = "lan3"; + }; + + port5: port@5 { + reg = <5>; + label = "lan4"; + phy-mode = "2500base-x"; + sfp = <&sfp2>; + managed = "in-band-status"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default", "dbdc"; + pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>; + pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>; +}; + -- 2.34.1
