Hi Uwe, On 15-11-2022 10:31 pm, Uwe Kleine-König wrote:
Hello, On Tue, Nov 15, 2022 at 01:20:05PM +0100, Naresh Solanki wrote:max6639_platform_data is not used by any in-kernel driver and does not address the MAX6639 fans separately. Move to device tree configuration with explicit properties to configure each fan.My overall impression is that this patch mixes too much things. IMHO it should be split in (at least) - Add dt support - Drop platform support - Add PWM provider support - Make use of the PWM API maybe also add the 2nd PWM in a separate step. Some more comments inline.Non-DT platform can still use this module with its default configuration. Signed-off-by: Marcello Sylvester Bauer <sylv@xxxxxxx> Signed-off-by: Naresh Solanki <Naresh.Solanki@xxxxxxxxxxxxx> --- drivers/hwmon/Kconfig | 1 + drivers/hwmon/max6639.c | 465 +++++++++++++++++++++++++++++++++------- 2 files changed, 392 insertions(+), 74 deletions(-) diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig index 5695b266abcf..ad1f6742ca50 100644 --- a/drivers/hwmon/Kconfig +++ b/drivers/hwmon/Kconfig @@ -1106,6 +1106,7 @@ config SENSORS_MAX6621 config SENSORS_MAX6639 tristate "Maxim MAX6639 sensor chip" depends on I2C + depends on PWM help If you say yes here you get support for the MAX6639 sensor chips. diff --git a/drivers/hwmon/max6639.c b/drivers/hwmon/max6639.c index 9b895402c80d..d1ae77e8f72e 100644 --- a/drivers/hwmon/max6639.c +++ b/drivers/hwmon/max6639.c @@ -19,7 +19,7 @@ #include <linux/hwmon-sysfs.h> #include <linux/err.h> #include <linux/mutex.h> -#include <linux/platform_data/max6639.h>This file is now unused and can be dropped.
Sure in next version.
+#include <linux/pwm.h>/* Addresses to scan */static const unsigned short normal_i2c[] = { 0x2c, 0x2e, 0x2f, I2C_CLIENT_END }; @@ -54,11 +54,20 @@ static const unsigned short normal_i2c[] = { 0x2c, 0x2e, 0x2f, I2C_CLIENT_END }; #define MAX6639_GCONFIG_PWM_FREQ_HI 0x08#define MAX6639_FAN_CONFIG1_PWM 0x80- +#define MAX6639_REG_FAN_CONFIG2a_PWM_POL 0x02 #define MAX6639_FAN_CONFIG3_THERM_FULL_SPEED 0x40 +#define MAX6639_FAN_CONFIG3_FREQ_MASK 0x03 +#define MAX6639_REG_TARGTDUTY_SLOT 120+/* Tach supported range. This internally controls tach frequency */static const int rpm_ranges[] = { 2000, 4000, 8000, 16000 };+/* Supported PWM frequency */+static const unsigned int freq_table[] = { 20, 33, 50, 100, 5000, 8333, 12500, + 25000 };I would have put these in a single line, or one line per freq, or at least aligned the last value such that it is at a higher column than the opening {.
Sure will align.
+ + +Three empty lines? One or two only should do it.
Oh. Will correct this in next version.
That depends on DT. For testing purpose, I specified different pwm handle & those pwm unreference in DT where available for use via sysfs export otherwise the resource was busy.#define FAN_FROM_REG(val, rpm_range) ((val) == 0 || (val) == 255 ? \ 0 : (rpm_ranges[rpm_range] * 30) / (val)) #define TEMP_LIMIT_TO_REG(val) clamp_val((val) / 1000, 0, 255) @@ -76,20 +85,24 @@ struct max6639_data { u16 temp[2]; /* Temperature, in 1/8 C, 0..255 C */ bool temp_fault[2]; /* Detected temperature diode failure */ u8 fan[2]; /* Register value: TACH count for fans >=30 */ + struct pwm_device *pwmd[2]; /* max6639 has two pwm device */ + u32 target_rpm[2]; + u32 max_rpm[2]; + u8 status; /* Detected channel alarms and fan failures *//* Register values only written to */- u8 pwm[2]; /* Register value: Duty cycle 0..120 */ u8 temp_therm[2]; /* THERM Temperature, 0..255 C (->_max) */ u8 temp_alert[2]; /* ALERT Temperature, 0..255 C (->_crit) */ u8 temp_ot[2]; /* OT Temperature, 0..255 C (->_emergency) *//* Register values initialized only once */- u8 ppr; /* Pulses per rotation 0..3 for 1..4 ppr */ - u8 rpm_range; /* Index in above rpm_ranges table */ - + u8 ppr[2]; /* Pulses per rotation 0..3 for 1..4 ppr */ + u8 rpm_range[2]; /* Index in above rpm_ranges table */ /* Optional regulator for FAN supply */ struct regulator *reg; + /* max6639 pwm chip */ + struct pwm_chip chip; };static struct max6639_data *max6639_update_device(struct device *dev)@@ -280,8 +293,12 @@ static ssize_t pwm_show(struct device *dev, struct device_attribute *dev_attr, { struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); struct max6639_data *data = dev_get_drvdata(dev); + struct pwm_state state; + + pwm_get_state(data->pwmd[attr->index], &state); + + return sprintf(buf, "%d\n", pwm_get_relative_duty_cycle(&state, 255));- return sprintf(buf, "%d\n", data->pwm[attr->index] * 255 / 120);}static ssize_t pwm_store(struct device *dev,@@ -290,9 +307,9 @@ static ssize_t pwm_store(struct device *dev, { struct sensor_device_attribute *attr = to_sensor_dev_attr(dev_attr); struct max6639_data *data = dev_get_drvdata(dev); - struct i2c_client *client = data->client; unsigned long val; int res; + struct pwm_state state;res = kstrtoul(buf, 10, &val);if (res) @@ -300,12 +317,12 @@ static ssize_t pwm_store(struct device *dev,val = clamp_val(val, 0, 255); - mutex_lock(&data->update_lock);- data->pwm[attr->index] = (u8)(val * 120 / 255); - i2c_smbus_write_byte_data(client, - MAX6639_REG_TARGTDUTY(attr->index), - data->pwm[attr->index]); - mutex_unlock(&data->update_lock); + pwm_get_state(data->pwmd[attr->index], &state); + pwm_set_relative_duty_cycle(&state, val, 255); + res = pwm_apply_state(data->pwmd[attr->index], &state); + if (res) + return res; + return count; }@@ -319,7 +336,7 @@ static ssize_t fan_input_show(struct device *dev,return PTR_ERR(data);return sprintf(buf, "%d\n", FAN_FROM_REG(data->fan[attr->index],- data->rpm_range)); + data->rpm_range[attr->index])); }static ssize_t alarm_show(struct device *dev,@@ -386,29 +403,41 @@ static struct attribute *max6639_attrs[] = { ATTRIBUTE_GROUPS(max6639);/*- * returns respective index in rpm_ranges table - * 1 by default on invalid range + * Get respective index in rpm_ranges table */ -static int rpm_range_to_reg(int range) +static int rpm_range_to_index(struct device *dev, u8 *index, int rpm) { - int i; - - for (i = 0; i < ARRAY_SIZE(rpm_ranges); i++) { - if (rpm_ranges[i] == range) - return i; + if (rpm < 0) + return -EINVAL; + + /* Set index based on chip support */ + switch (rpm) { + case 0 ... 2000: + *index = 0; + break; + case 2001 ... 4000: + *index = 1; + break; + case 4001 ... 8000: + *index = 2; + break; + case 8001 ... 16000: + *index = 3; + break; + default: + /* Use max range for higher RPM */ + dev_warn(dev, + "RPM higher than supported range. Default to 16000 RPM"); + *index = 3; } - - return 1; /* default: 4000 RPM */ + return 0; }static int max6639_init_client(struct i2c_client *client,struct max6639_data *data) { - struct max6639_platform_data *max6639_info = - dev_get_platdata(&client->dev); - int i; - int rpm_range = 1; /* default: 4000 RPM */ - int err; + int i, err; + struct pwm_state state;/* Reset chip to default values, see below for GCONFIG setup */err = i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG, @@ -416,51 +445,29 @@ static int max6639_init_client(struct i2c_client *client, if (err) goto exit;- /* Fans pulse per revolution is 2 by default */- if (max6639_info && max6639_info->ppr > 0 && - max6639_info->ppr < 5) - data->ppr = max6639_info->ppr; - else - data->ppr = 2; - data->ppr -= 1; - - if (max6639_info) - rpm_range = rpm_range_to_reg(max6639_info->rpm_range); - data->rpm_range = rpm_range; - for (i = 0; i < 2; i++) {/* Set Fan pulse per revolution */- err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_PPR(i), - data->ppr << 6); + err = i2c_smbus_write_byte_data(client, MAX6639_REG_FAN_PPR(i), + data->ppr[i] << 6); if (err) goto exit;/* Fans config PWM, RPM */err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_CONFIG1(i), - MAX6639_FAN_CONFIG1_PWM | rpm_range); - if (err) - goto exit; - - /* Fans PWM polarity high by default */ - if (max6639_info && max6639_info->pwm_polarity == 0) - err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_CONFIG2a(i), 0x00); - else - err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_CONFIG2a(i), 0x02); + MAX6639_REG_FAN_CONFIG1(i), + MAX6639_FAN_CONFIG1_PWM | + data->rpm_range[i]); if (err) goto exit;/*- * /THERM full speed enable, + * /THERM full speed disable, * PWM frequency 25kHz, see also GCONFIG below */ err = i2c_smbus_write_byte_data(client, - MAX6639_REG_FAN_CONFIG3(i), - MAX6639_FAN_CONFIG3_THERM_FULL_SPEED | 0x03); + MAX6639_REG_FAN_CONFIG3(i), + 0x03); if (err) goto exit;@@ -469,31 +476,35 @@ static int max6639_init_client(struct i2c_client *client,data->temp_alert[i] = 90; data->temp_ot[i] = 100; err = i2c_smbus_write_byte_data(client, - MAX6639_REG_THERM_LIMIT(i), - data->temp_therm[i]); + MAX6639_REG_THERM_LIMIT(i), + data->temp_therm[i]); if (err) goto exit; err = i2c_smbus_write_byte_data(client, - MAX6639_REG_ALERT_LIMIT(i), - data->temp_alert[i]); + MAX6639_REG_ALERT_LIMIT(i), + data->temp_alert[i]); if (err) goto exit; err = i2c_smbus_write_byte_data(client, - MAX6639_REG_OT_LIMIT(i), data->temp_ot[i]); + MAX6639_REG_OT_LIMIT(i), + data->temp_ot[i]); if (err) goto exit;- /* PWM 120/120 (i.e. 100%) */- data->pwm[i] = 120; - err = i2c_smbus_write_byte_data(client, - MAX6639_REG_TARGTDUTY(i), data->pwm[i]); + /* Configure PWM controller */ + pwm_get_state(data->pwmd[i], &state); + pwm_set_relative_duty_cycle(&state, data->target_rpm[i], + data->max_rpm[i]); + err = pwm_apply_state(data->pwmd[i], &state); if (err) goto exit; + } /* Start monitoring */ err = i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG, MAX6639_GCONFIG_DISABLE_TIMEOUT | MAX6639_GCONFIG_CH2_LOCAL | MAX6639_GCONFIG_PWM_FREQ_HI); + exit: return err; } @@ -524,12 +535,276 @@ static void max6639_regulator_disable(void *data) regulator_disable(data); }+static int max6639_probe_child_from_dt(struct i2c_client *client,+ struct device_node *child, + struct max6639_data *data) + +{ + struct device *dev = &client->dev; + u32 i, maxrpm; + int val, err; + + err = of_property_read_u32(child, "reg", &i); + if (err) { + dev_err(dev, "missing reg property of %pOFn\n", child); + return err; + } + + if (i >= 2) { + dev_err(dev, "invalid reg %d of %pOFn\n", i, child); + return -EINVAL; + } + + err = of_property_read_u32(child, "pulses-per-revolution", &val); + if (err) { + dev_err(dev, "missing pulses-per-revolution property of %pOFn", + child); + return err; + } + + if (val < 0 || val > 5) { + dev_err(dev, "invalid pulses-per-revolution %d of %pOFn\n", val, + child); + return -EINVAL; + } + data->ppr[i] = val; + + err = of_property_read_u32(child, "max-rpm", &maxrpm); + if (err) { + dev_err(dev, "missing max-rpm property of %pOFn\n", child); + return err; + } + + err = rpm_range_to_index(dev, &data->rpm_range[i], maxrpm); + if (err) { + dev_err(dev, "invalid max-rpm %d of %pOFn\n", maxrpm, child); + return err; + } + data->max_rpm[i] = maxrpm; + + err = of_property_read_u32(child, "target-rpm", &val); + /* Use provided target RPM else default to maxrpm */ + if (!err) + data->target_rpm[i] = val; + else + data->target_rpm[i] = maxrpm; + + /* Get pwms property for PWM control */ + data->pwmd[i] = devm_fwnode_pwm_get(dev, &child->fwnode, NULL); + + if (!IS_ERR(data->pwmd[i])) + return 0; + + if (PTR_ERR(data->pwmd[i]) == -EPROBE_DEFER) + return PTR_ERR(data->pwmd[i]); + + dev_dbg(dev, "Using chip default PWM"); + data->pwmd[i] = pwm_request_from_chip(&data->chip, i, NULL); + if (!IS_ERR(data->pwmd[i])) + return 0;Are these PWMs usuable at all for a consumer other than the driver itself? If not I'd doubt the added value of this patch.
+ dev_dbg(dev, "Failed to configure pwm for fan %d", i); + return PTR_ERR_OR_ZERO(data->pwmd[i]); +} + +static int max6639_probe_from_dt(struct i2c_client *client, + struct max6639_data *data) +{ + struct device *dev = &client->dev; + const struct device_node *np = dev->of_node; + struct device_node *child; + int err; + + /* Compatible with non-DT platforms */ + if (!np) + return 0; + + for_each_child_of_node(np, child) { + if (strcmp(child->name, "fan")) + continue; + + err = max6639_probe_child_from_dt(client, child, data); + if (err) { + of_node_put(child); + return err; + } + } + + return 0; +} + +static struct max6639_data *to_max6639_pwm(struct pwm_chip *chip) +{ + return container_of(chip, struct max6639_data, chip); +} + +static void max6639_pwm_get_state(struct pwm_chip *chip, + struct pwm_device *pwm, + struct pwm_state *state) +{ + + struct max6639_data *data = to_max6639_pwm(chip); + struct i2c_client *client = data->client; + int value, i = pwm->hwpwm, x;Please use pwm->hwpwm directly instead of i, this makes the code IMHO a bit more readable.
I used variable 'i' to make it look short. Can switch to pwm->hwpwm
+ unsigned int freq; + + mutex_lock(&data->update_lock); + + value = i2c_smbus_read_byte_data(client, MAX6639_REG_FAN_CONFIG1(i)); + if (value < 0) + goto abort; + + if (value & MAX6639_FAN_CONFIG1_PWM) { + state->enabled = true; + + /* Determine frequency from respective registers */ + value = i2c_smbus_read_byte_data(client, + MAX6639_REG_FAN_CONFIG3(i)); + if (value < 0) + goto abort; + x = value & MAX6639_FAN_CONFIG3_FREQ_MASK; + + value = i2c_smbus_read_byte_data(client, MAX6639_REG_GCONFIG); + if (value < 0) + goto abort; + if (value & MAX6639_GCONFIG_PWM_FREQ_HI) + x |= 0x4; + x &= 0x7; + freq = freq_table[x]; + + state->period = DIV_ROUND_UP_ULL(NSEC_PER_SEC, freq);both NSEC_PER_SEC and freq fit into an unsigned int, so you can use the (cheaper) DIV_ROUND_UP here.
Sure. will update in next version
+ + value = i2c_smbus_read_byte_data(client, + MAX6639_REG_TARGTDUTY(i)); + if (value < 0) + goto abort; + /* max6639 supports 120 slots only */ + state->duty_cycle = DIV_ROUND_UP_ULL(value * state->period, + 120);s/120/MAX6639_REG_TARGTDUTY_SLOT/ ? value * state->period might overflow. Use something like mul_u64_u32_div. (Hmm, there doesn't seem to be a variant for unsigned * unsigned / unsigned?)
Yeah that seems better. Will update in next version
You're loosing precision here. Consider freq = 8333 and TARGTDUTY = 97 then you have state->period = 120005 and calulate duty_cycle as: DIV_ROUND_UP_ULL(97 * 120005, 120) = 97005 . The exact value is (I guess) 97 * NSEC_PER_SEC / (8333 * 120) = 97003.880
For this chip, it may not matter as it supports only 120 slots.
+ value = i2c_smbus_read_byte_data(client, + MAX6639_REG_FAN_CONFIG2a(i)); + if (value < 0) + goto abort; + value &= MAX6639_REG_FAN_CONFIG2a_PWM_POL; + state->polarity = (value != 0); + } else + state->enabled = false; + +abort: + mutex_unlock(&data->update_lock); + +} + +static int max6639_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, + const struct pwm_state *state) +{ + struct max6639_data *data = to_max6639_pwm(chip); + struct i2c_client *client = data->client; + int value = 0, i = pwm->hwpwm, x;Please use pwm->hwpwm directly instead of i, this makes the code IMHO a bit more readable.
I used variable 'i' to make it look short. Can switch to pwm->hwpwm
+ unsigned int freq; + struct pwm_state cstate; + + pwm_get_state(pwm, &cstate);Please don't use pwm API functions in PWM callbacks. Accessing pwm->state is fine here.
Sure.
+ mutex_lock(&data->update_lock); + + if (state->period != cstate.period) { + /* Configure frequency */ + freq = DIV_ROUND_UP_ULL(NSEC_PER_SEC, state->period); + /* Chip supports limited number of frequency */ + for (x = 0; x < sizeof(freq_table); x++) + if (freq < freq_table[x]) + break;For state->period = 80000 we get: freq = 12500 and then x = 7 is picked while x = 6 would be an exact match. I think you just need if (freq <= freq_table[x])
Yes. Will update in next revision.
+ value = i2c_smbus_read_byte_data(client, + MAX6639_REG_FAN_CONFIG3(i)); + if (value < 0) + goto abort; + value &= ~MAX6639_FAN_CONFIG3_FREQ_MASK; + value |= (x & MAX6639_FAN_CONFIG3_FREQ_MASK); + value = i2c_smbus_write_byte_data(client, + MAX6639_REG_FAN_CONFIG3(i), + value); + + value = i2c_smbus_read_byte_data(client, MAX6639_REG_GCONFIG); + if (value < 0) + goto abort; + + if ((value & MAX6639_GCONFIG_PWM_FREQ_HI) && (x >> 2)) + value &= ~MAX6639_GCONFIG_PWM_FREQ_HI; + else + value |= MAX6639_GCONFIG_PWM_FREQ_HI; + value = i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG, + value);Why does it depend on MAX6639_GCONFIG_PWM_FREQ_HI being already set if you need to set it?
Yes. Will update in next version
+ if (value < 0) + goto abort; + } + + /* Configure dutycycle */ + if (state->duty_cycle != cstate.duty_cycle) {That check is wrong if you go from .duty_cycle = 50000; .period = 200000 to .duty_cycle = 50000; .period = 100000
Yes. Will update in next revision.
+ value = DIV_ROUND_UP_ULL( + state->duty_cycle * MAX6639_REG_TARGTDUTY_SLOT, + state->period);Please round down here. (And test with PWM_DEBUG which might have told you given the right tests.) Also please use the real period to determine the register value. (Otherwise for a request with .duty_cycle = 40000; .period = 150000 where a real period of 120004.8 ns is picked you get MAX6639_REG_TARGTDUTY_SLOT = 32 which results in a duty cycle of 32001.28 ns, while with MAX6639_REG_TARGTDUTY_SLOT = 39 you'd get 39001.56 ns.
Sure will update to round down.
+ value = i2c_smbus_write_byte_data(client, + MAX6639_REG_TARGTDUTY(i), + value); + if (value < 0) + goto abort; + } + + /* Configure polarity */ + if (state->polarity != cstate.polarity) { + value = i2c_smbus_read_byte_data(client, + MAX6639_REG_FAN_CONFIG2a(i)); + if (value < 0) + goto abort; + if (state->polarity == PWM_POLARITY_NORMAL) + value |= MAX6639_REG_FAN_CONFIG2a_PWM_POL; + else + value &= ~MAX6639_REG_FAN_CONFIG2a_PWM_POL; + value = i2c_smbus_write_byte_data(client, + MAX6639_REG_FAN_CONFIG2a(i), + value); + if (value < 0) + goto abort; + } + + if (state->enabled == cstate.enabled) + goto abort;Please use goto only for error handling. >> ++ value = i2c_smbus_read_byte_data(client, MAX6639_REG_FAN_CONFIG1(i)); + if (value < 0) + goto abort; + if (state->enabled) + value |= MAX6639_FAN_CONFIG1_PWM; + else + value &= ~MAX6639_FAN_CONFIG1_PWM; + + value = i2c_smbus_write_byte_data(client, MAX6639_REG_FAN_CONFIG1(i), + value); + if (value < 0) + goto abort; + value = 0; + +abort: + mutex_unlock(&data->update_lock); + + return value; +} + +static const struct pwm_ops max6639_pwm_ops = { + .apply = max6639_pwm_apply, + .get_state = max6639_pwm_get_state, + .owner = THIS_MODULE, +}; + static int max6639_probe(struct i2c_client *client) { struct device *dev = &client->dev; struct max6639_data *data; struct device *hwmon_dev; - int err; + int err, i;data = devm_kzalloc(dev, sizeof(struct max6639_data), GFP_KERNEL);if (!data) @@ -537,11 +812,26 @@ static int max6639_probe(struct i2c_client *client)data->client = client; + /* Add PWM controller of max6639 */+ data->chip.dev = dev; + data->chip.ops = &max6639_pwm_ops; + data->chip.npwm = 2; + data->chip.of_pwm_n_cells = 3;Please drop this, of_pwmchip_add() overwrites it anyhow.
Sure.
+ + err = devm_pwmchip_add(dev, &data->chip); + if (err < 0) { + dev_err(dev, "failed to add PWM chip %d\n", err);dev_err_probe please.
Sure.
+ return err; + } + data->reg = devm_regulator_get_optional(dev, "fan"); if (IS_ERR(data->reg)) { - if (PTR_ERR(data->reg) != -ENODEV) - return PTR_ERR(data->reg); - + if (PTR_ERR(data->reg) != -ENODEV) { + err = (int)PTR_ERR(data->reg); + dev_warn(dev, "Failed looking up fan supply: %d\n", + err);unrelated change. Also dev_probe_err is better suited here.
Sure.
+ return err; + } data->reg = NULL; } else { /* Spin up fans */ @@ -560,6 +850,22 @@ static int max6639_probe(struct i2c_client *client)mutex_init(&data->update_lock); + /* Below are defaults leter overridden by DT properties */+ for (i = 0; i < 2; i++) { + /* 4000 RPM */ + data->rpm_range[i] = 1; + data->ppr[i] = 2; + /* Max. temp. 80C/90C/100C */ + data->temp_therm[i] = 80; + data->temp_alert[i] = 90; + data->temp_ot[i] = 100; + } + + /* Probe from DT to get configuration */ + err = max6639_probe_from_dt(client, data); + if (err) + return err; + /* Initialize the max6639 chip */ err = max6639_init_client(client, data); if (err < 0) @@ -571,6 +877,7 @@ static int max6639_probe(struct i2c_client *client) return PTR_ERR_OR_ZERO(hwmon_dev); }+#if IS_ENABLED(CONFIG_PM_SLEEP)unrelated change
Have put this to avoid error when CONFIG_PM_SLEEP is disabled.
static int max6639_suspend(struct device *dev) { struct i2c_client *client = to_i2c_client(dev); @@ -608,6 +915,7 @@ static int max6639_resume(struct device *dev) return i2c_smbus_write_byte_data(client, MAX6639_REG_GCONFIG, ret & ~MAX6639_GCONFIG_STANDBY); } +#endifstatic const struct i2c_device_id max6639_id[] = {{"max6639", 0}, @@ -616,13 +924,22 @@ static const struct i2c_device_id max6639_id[] = {MODULE_DEVICE_TABLE(i2c, max6639_id); -static DEFINE_SIMPLE_DEV_PM_OPS(max6639_pm_ops, max6639_suspend, max6639_resume);+#ifdef CONFIG_OFNote that ACPI also uses of_match_table.+static const struct of_device_id maxim_of_platform_match[] = { + {.compatible = "maxim,max6639"}, + {}, +}; +MODULE_DEVICE_TABLE(of, maxim_of_platform_match); +#endif + +static SIMPLE_DEV_PM_OPS(max6639_pm_ops, max6639_suspend, max6639_resume);static struct i2c_driver max6639_driver = {.class = I2C_CLASS_HWMON, .driver = { .name = "max6639", .pm = pm_sleep_ptr(&max6639_pm_ops), + .of_match_table = of_match_ptr(maxim_of_platform_match), }, .probe_new = max6639_probe, .id_table = max6639_id,Best regards Uwe
Regards, Naresh
