Yea my bad this was not supposed to be sent this soon.
Well either way V2 will come soon
On Mon, Nov 14 2022 at 05:29:31 PM +01:00:00, Krzysztof Kozlowski
<krzysztof.kozlowski@xxxxxxxxxx> wrote:
On 14/11/2022 17:25, Martin Botka wrote:
CB1 is Compute Module style board that plugs into Rpi board style
adapter or
Manta 3D printer boards (M4P/M8P).
The board has:
H616 SoC
1GB of RAM
AXP313A PMIC
And the actual boards that CB1 plugs in are just extension to it
with ports and
thus are not split in DT.
Boards have:
4x (3x for Manta boards) USB and 1 USB OTG.
SDcard slot for loading images.
Ethernet port wired to the internal PHY.
2x HDMI 2.0.
Power and Status LEDs.
Currently working:
Booting
USB
UART
Signed-off-by: Martin Botka <martin.botka@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../dts/allwinner/sun50i-h616-biqu-cb1.dts | 191
++++++++++++++++++
2 files changed, 192 insertions(+)
create mode 100644
arch/arm64/boot/dts/allwinner/sun50i-h616-biqu-cb1.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile
b/arch/arm64/boot/dts/allwinner/Makefile
index 6a96494a2e0a..223f1be73541 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -38,5 +38,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-biqu-cb1.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-biqu-cb1.dts
b/arch/arm64/boot/dts/allwinner/sun50i-h616-biqu-cb1.dts
new file mode 100644
index 000000000000..2225a965dddc
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-biqu-cb1.dts
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2022 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "BIQU CB1";
+ compatible = "allwinner,sun50i-h616";
That's not a proper board compatible.
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+ default-state = "on";
+ };
+
+ led-1 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+ };
+ };
+
+ reg_vcc5v: vcc5v {
regulator prefix. Keep it consistent.
+ /* board wide 5V supply directly from the USB-C socket */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb1_vbus: regulator-usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_vcc5v>;
+ enable-active-high;
+ gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_dldo1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ no-1-8-v;
+ bus-width = <4>;
+ status = "disabled";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp1530: pmic@36 {
+ compatible = "x-powers,axp1530";
+ status = "okay";
Drop.
+ reg = <0x36>;
+ wakeup-source;
+
+ standby_param: standby_param {
Does not look like supported/documented/valid property. Test your DTS
with `make dtbs_check`.
Best regards,
Krzysztof
