On 14/11/2022 08:57, Naresh Solanki wrote: > From: Marcello Sylvester Bauer <sylv@xxxxxxx> Subject: I asked to drop the redundant words, but you re-added now in different form. So again, drop "dt-schema". > > The MAX597x is a hot swap controller with configurable fault protection. > It also has 10bit ADC for current & voltage measurements. > > Signed-off-by: Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx> > Signed-off-by: Marcello Sylvester Bauer <sylv@xxxxxxx> > Signed-off-by: Naresh Solanki <Naresh.Solanki@xxxxxxxxxxxxx> > --- > .../bindings/mfd/maxim,max5970.yaml | 172 ++++++++++++++++++ > 1 file changed, 172 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mfd/maxim,max5970.yaml > > diff --git a/Documentation/devicetree/bindings/mfd/maxim,max5970.yaml b/Documentation/devicetree/bindings/mfd/maxim,max5970.yaml > new file mode 100644 > index 000000000000..a93b6e009b9a > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/maxim,max5970.yaml > @@ -0,0 +1,172 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/mfd/maxim,max5970.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Regulator for MAX5970 smart switch from Maxim Integrated. > + > +maintainers: > + - Patrick Rudolph <patrick.rudolph@xxxxxxxxxxxxx> > + > +description: | > + The smart switch provides no output regulation, but independent fault protection > + and voltage and current sensing. > + Programming is done through I2C bus. > + > + Datasheets: > + https://datasheets.maximintegrated.com/en/ds/MAX5970.pdf > + https://datasheets.maximintegrated.com/en/ds/MAX5978.pdf > + > +properties: > + compatible: > + enum: > + - maxim,max5970 > + - maxim,max5978 > + > + reg: > + maxItems: 1 > + > + interrupts: > + maxItems: 1 > + > + leds: > + type: object > + description: > + Properties for four LEDS. > + > + properties: > + "#address-cells": > + const: 1 > + > + "#size-cells": > + const: 0 > + > + patternProperties: > + "^led@[0-3]$": > + $ref: /schemas/leds/common.yaml# > + type: object > + > + additionalProperties: false > + > + vss1-supply: > + description: Supply of the first channel. > + > + vss2-supply: > + description: Supply of the second channel. > + > + "#io-channel-cells": > + const: 1 > + > + regulators: > + type: object > + description: > + Properties for regulator. That's not correct description. This is not one regulator. > + > + patternProperties: > + "^sw[0-1]$": > + $ref: /schemas/regulator/regulator.yaml# > + type: object unevaluatedProperties: false > + properties: > + shunt-resistor-micro-ohms: > + description: | > + The value of curent sense resistor in microohms. Typo: current > + > + required: > + - shunt-resistor-micro-ohms > + > + additionalProperties: false > + > +required: > + - compatible > + - reg > + - regulators > + - vss1-supply > + > +allOf: > + - if: > + properties: > + compatible: > + enum: > + - maxim,max5970 > + then: > + properties: > + io-channels: > + items: > + - description: voltage first channel > + - description: current first channel > + - description: voltage second channel > + - description: current second channel > + description: | > + Voltage and current for first and second channel. > + required: > + - vss2-supply This is a friendly reminder during the review process. It seems my previous comments were not fully addressed. Maybe my feedback got lost between the quotes, maybe you just forgot to apply it. Please go back to the previous discussion and either implement all requested changes or keep discussing them. Comment was: "Also, add it in the existing example." > + else: > + properties: > + io-channels: > + items: > + - description: voltage first channel > + - description: current first channel > + description: | > + Voltage and current for first channel. > + > +additionalProperties: false > + > +examples: > + - | > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + regulator@3a { > + compatible = "maxim,max5978"; > + reg = <0x3a>; > + vss1-supply = <&p3v3>; > + > + regulators { > + sw0_ref_0: sw0 { > + regulator-compatible = "SW0"; Use 4 spaces for example indentation. > + shunt-resistor-micro-ohms = <12000>; > + }; > + }; > + > + leds { > + #address-cells = <1>; > + #size-cells = <0>; > + led@0 { > + reg = <0>; > + label = "led0"; > + default-state = "on"; > + }; > + led@1 { > + reg = <1>; > + label = "led1"; > + default-state = "on"; > + }; > + }; > + }; > + }; > + > + - | > + i2c { > + #address-cells = <1>; > + #size-cells = <0>; > + > + regulator@3a { > + compatible = "maxim,max5970"; > + reg = <0x3a>; > + vss1-supply = <&p3v3>; > + vss2-supply = <&p5v>; > + > + regulators { > + sw0_ref_1: sw0 { > + regulator-compatible = "SW0"; > + shunt-resistor-micro-ohms = <12000>; > + }; > + sw1_ref_1: sw1 { > + regulator-compatible = "SW1"; > + shunt-resistor-micro-ohms = <10000>; > + }; > + }; > + }; > + }; > +... Best regards, Krzysztof
