Re: [PATCH v1 7/9] arm64: dts: qcom: sm8350: Add display system nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sat, 29 Oct 2022 at 00:01, Krzysztof Kozlowski
<krzysztof.kozlowski@xxxxxxxxxx> wrote:
>
> On 28/10/2022 08:08, Robert Foss wrote:
> > Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these
> > nodes the display subsystem is configured to support
> > one DSI output.
> >
> > Signed-off-by: Robert Foss <robert.foss@xxxxxxxxxx>
> > ---
> >  arch/arm64/boot/dts/qcom/sm8350.dtsi | 196 ++++++++++++++++++++++++++-
> >  1 file changed, 192 insertions(+), 4 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > index b6e44cd3b394..eaa3cdee1860 100644
> > --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> > @@ -3,6 +3,7 @@
> >   * Copyright (c) 2020, Linaro Limited
> >   */
> >
> > +#include <dt-bindings/interconnect/qcom,sm8350.h>
> >  #include <dt-bindings/interrupt-controller/arm-gic.h>
> >  #include <dt-bindings/clock/qcom,dispcc-sm8350.h>
> >  #include <dt-bindings/clock/qcom,gcc-sm8350.h>
> > @@ -2535,14 +2536,200 @@ usb_2_dwc3: usb@a800000 {
> >                       };
> >               };
> >
> > +             mdss: mdss@ae00000 {
> > +                     compatible = "qcom,sm8350-mdss";
> > +                     reg = <0 0x0ae00000 0 0x1000>;
> > +                     reg-names = "mdss";
> > +
> > +                     interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
> > +                                     <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
> > +                     interconnect-names = "mdp0-mem", "mdp1-mem";
> > +
> > +                     power-domains = <&dispcc MDSS_GDSC>;
> > +                     resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
> > +
> > +                     clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +                              <&gcc GCC_DISP_HF_AXI_CLK>,
> > +                              <&gcc GCC_DISP_SF_AXI_CLK>,
> > +                              <&dispcc DISP_CC_MDSS_MDP_CLK>;
> > +                     clock-names = "iface", "bus", "nrt_bus", "core";
> > +
> > +                     interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> > +                     interrupt-controller;
> > +                     #interrupt-cells = <1>;
> > +
> > +                     status = "ok";
>
> No need for this.

Ack, I'll switch to disabled.

>
> > +
> > +                     #address-cells = <2>;
> > +                     #size-cells = <2>;
> > +                     ranges;
> > +
> > +                     mdss_mdp: mdp@ae01000 {
>
> Node name: display-controller

Ack.

> > +                             compatible = "qcom,sm8350-dpu";
> > +                             reg = <0 0x0ae01000 0 0x8f000>,
> > +                                   <0 0x0aeb0000 0 0x2008>;
> > +                             reg-names = "mdp", "vbif";
> > +                             iommus = <&apps_smmu 0x820 0x402>;
> > +
> > +                             clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> > +                                     <&gcc GCC_DISP_SF_AXI_CLK>,
> > +                                     <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +                                     <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
> > +                                     <&dispcc DISP_CC_MDSS_MDP_CLK>,
> > +                                     <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> > +                             clock-names = "bus",
> > +                                           "nrt_bus",
> > +                                           "iface",
> > +                                           "lut",
> > +                                           "core",
> > +                                           "vsync";
> > +
> > +                             assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
> > +                             assigned-clock-rates = <19200000>;
> > +
> > +                             operating-points-v2 = <&mdp_opp_table>;
> > +                             power-domains = <&rpmhpd SM8350_MMCX>;
> > +
> > +                             interrupt-parent = <&mdss>;
> > +                             interrupts = <0>;
> > +
> > +                             status = "ok";
> > +
> > +                             ports {
> > +                                     #address-cells = <1>;
> > +                                     #size-cells = <0>;
> > +
> > +                                     port@0 {
> > +                                             reg = <0>;
> > +                                             dpu_intf1_out: endpoint {
> > +                                                     remote-endpoint = <&dsi0_in>;
> > +                                             };
> > +                                     };
> > +                             };
> > +
> > +                             mdp_opp_table: mdp-opp-table {
>
> I have doubts that it passes dtbs_checks... opp-table

Ack.

>
> > +                                     compatible = "operating-points-v2";
> > +
> > +                                     opp-200000000 {
> > +                                             opp-hz = /bits/ 64 <200000000>;
> > +                                             required-opps = <&rpmhpd_opp_low_svs>;
> > +                                     };
> > +
> > +                                     opp-300000000 {
> > +                                             opp-hz = /bits/ 64 <300000000>;
> > +                                             required-opps = <&rpmhpd_opp_svs>;
> > +                                     };
> > +
> > +                                     opp-345000000 {
> > +                                             opp-hz = /bits/ 64 <345000000>;
> > +                                             required-opps = <&rpmhpd_opp_svs_l1>;
> > +                                     };
> > +
> > +                                     opp-460000000 {
> > +                                             opp-hz = /bits/ 64 <460000000>;
> > +                                             required-opps = <&rpmhpd_opp_nom>;
> > +                                     };
> > +                             };
> > +                     };
> > +
> > +                     dsi0: dsi@ae94000 {
> > +                             compatible = "qcom,mdss-dsi-ctrl";
> > +                             reg = <0 0x0ae94000 0 0x400>;
> > +                             reg-names = "dsi_ctrl";
> > +
> > +                             interrupt-parent = <&mdss>;
> > +                             interrupts = <4>;
> > +
> > +                             clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
> > +                                      <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
> > +                                      <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
> > +                                      <&dispcc DISP_CC_MDSS_ESC0_CLK>,
> > +                                      <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +                                      <&gcc GCC_DISP_HF_AXI_CLK>;
> > +                             clock-names = "byte",
> > +                                           "byte_intf",
> > +                                           "pixel",
> > +                                           "core",
> > +                                           "iface",
> > +                                           "bus";
> > +
> > +                             assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
> > +                                               <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
> > +                             assigned-clock-parents = <&dsi0_phy 0>,
> > +                                                      <&dsi0_phy 1>;
> > +
> > +                             operating-points-v2 = <&dsi_opp_table>;
> > +                             power-domains = <&rpmhpd SM8350_MMCX>;
> > +
> > +                             phys = <&dsi0_phy>;
> > +                             phy-names = "dsi";
> > +
> > +                             status = "disabled";
> > +
> > +                             ports {
> > +                                     #address-cells = <1>;
> > +                                     #size-cells = <0>;
> > +
> > +                                     port@0 {
> > +                                             reg = <0>;
> > +                                             dsi0_in: endpoint {
> > +                                                     remote-endpoint = <&dpu_intf1_out>;
> > +                                             };
> > +                                     };
> > +
> > +                                     port@1 {
> > +                                             reg = <1>;
> > +                                             dsi0_out: endpoint {
> > +                                             };
> > +                                     };
> > +                             };
> > +                     };
> > +
> > +                     dsi0_phy: dsi-phy@ae94400 {
>
> Just "phy". I think Dmitry was renaming all of these.

Ack.

>
> > +                             compatible = "qcom,dsi-phy-5nm-8350";
> > +                             reg = <0 0x0ae94400 0 0x200>,
> > +                                   <0 0x0ae94600 0 0x280>,
> > +                                   <0 0x0ae94900 0 0x260>;
> > +                             reg-names = "dsi_phy",
> > +                                         "dsi_phy_lane",
> > +                                         "dsi_pll";
> > +
> > +                             #clock-cells = <1>;
> > +                             #phy-cells = <0>;
> > +
> > +                             clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
> > +                                      <&rpmhcc RPMH_CXO_CLK>;
> > +                             clock-names = "iface", "ref";
> > +
> > +                             status = "disabled";
> > +
> > +                             dsi_opp_table: dsi-opp-table {
>
> opp-table

Ack

>
> Run `make dtbs_check`

I had a look after fixing the above and I'm seeing some other issues.
Due to the dts/dt-binding rework that Dmitry is doing, I'll leave some
warnings, which can be addressed once the rework changes have landed.

>
>
> Best regards,
> Krzysztof
>



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux