Using extcon USB host mode works properly on DR interface, e.g.
enabling/disabling VBUS. But USB device mode is not working.
Fix this by switching to usb-role-switch instead.
Fixes: dfcd1b6f7620 ("arm64: dts: freescale: add initial device tree for TQMa8MQML with i.MX8MM")
Signed-off-by: Alexander Stein <alexander.stein@xxxxxxxxxxxxxxx>
---
Changes in v2:
* Improve the commit message describing the actual issue being fixed
.../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 32 +++++++++++++++----
1 file changed, 26 insertions(+), 6 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
index bfb44630da6b..56323c989d55 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
@@ -34,11 +34,25 @@ reg_usdhc2_vmmc: regulator-vmmc {
off-on-delay-us = <12000>;
};
- extcon_usbotg1: extcon-usbotg1 {
- compatible = "linux,extcon-usb-gpio";
+ connector {
+ compatible = "gpio-usb-b-connector", "usb-b-connector";
+ type = "micro";
+ label = "X19";
pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usb1_extcon>;
- id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&pinctrl_usb1_connector>;
+ id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usb_dr_connector: endpoint {
+ remote-endpoint = <&usb1_drd_sw>;
+ };
+ };
+ };
};
};
@@ -106,13 +120,19 @@ &usbotg1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbotg1>;
dr_mode = "otg";
- extcon = <&extcon_usbotg1>;
srp-disable;
hnp-disable;
adp-disable;
power-active-high;
over-current-active-low;
+ usb-role-switch;
status = "okay";
+
+ port {
+ usb1_drd_sw: endpoint {
+ remote-endpoint = <&usb_dr_connector>;
+ };
+ };
};
&usbotg2 {
@@ -242,7 +262,7 @@ pinctrl_usbotg1: usbotg1grp {
<MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x84>;
};
- pinctrl_usb1_extcon: usb1-extcongrp {
+ pinctrl_usb1_connector: usb1-connectorgrp {
fsl,pins = <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x1c0>;
};
--
2.34.1
