Switch the DT binding to a YAML schema to enable the DT validation. Dropped deprecated compatibles and properties described in txt file. Signed-off-by: Vadym Kochan <vadym.kochan@xxxxxxxxxxx> --- .../bindings/mtd/marvell,nand-controller.yaml | 199 ++++++++++++++++++ .../devicetree/bindings/mtd/marvell-nand.txt | 126 ----------- 2 files changed, 199 insertions(+), 126 deletions(-) create mode 100644 Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml delete mode 100644 Documentation/devicetree/bindings/mtd/marvell-nand.txt diff --git a/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml b/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml new file mode 100644 index 000000000000..535b7f8903c8 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml @@ -0,0 +1,199 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/marvell,nand-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell NAND Flash Controller (NFC) + +maintainers: + - Miquel Raynal <miquel.raynal@xxxxxxxxxxx> + +properties: + + compatible: + oneOf: + - items: + - const: marvell,armada-8k-nand-controller + - const: marvell,armada370-nand-controller + - const: marvell,armada370-nand-controller + - const: marvell,pxa3xx-nand-controller + + reg: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + interrupts: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + description: | + Shall reference the NAND controller clocks, the second one is + is only needed for the Armada 7K/8K SoCs + + clock-names: + items: + - const: core + - const: reg + description: | + Mandatory if there is a second clock, in this case there + should be one clock named "core" and another one named "reg" + + dmas: + maxItems: 1 + description: rxtx DMA channel + + dma-names: + items: + - const: rxtx + + marvell,system-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: Syscon node that handles NAND controller related registers + +patternProperties: + "^nand@[0-3]$": + type: object + properties: + + reg: + minimum: 0 + maximum: 3 + + nand-rb: + minimum: 0 + maximum: 1 + + nand-ecc-strength: + enum: [1, 4, 8] + + nand-on-flash-bbt: true + + nand-ecc-mode: true + + nand-ecc-algo: + description: | + This property is essentially useful when not using hardware ECC. + Howerver, it may be added when using hardware ECC for clarification + but will be ignored by the driver because ECC mode is chosen depending + on the page size and the strength required by the NAND chip. + This value may be overwritten with nand-ecc-strength property. + + nand-ecc-step-size: + const: 512 + description: | + Marvell's NAND flash controller does use fixed strength + (1-bit for Hamming, 16-bit for BCH), so the actual step size + will shrink or grow in order to fit the required strength. + Step sizes are not completely random for all and follow certain + patterns described in AN-379, "Marvell SoC NFC ECC". + + label: + $ref: /schemas/types.yaml#/definitions/string + + partitions: + type: object + $ref: "/schemas/mtd/partitions/partition.yaml" + + marvell,nand-keep-config: + description: | + Orders the driver not to take the timings from the core and + leaving them completely untouched. Bootloader timings will then + be used. + $ref: /schemas/types.yaml#/definitions/flag + + marvell,nand-enable-arbiter: + description: | + To enable the arbiter, all boards blindly used it, + this bit was set by the bootloader for many boards and even if + it is marked reserved in several datasheets, it might be needed to set + it (otherwise it is harmless) so whether or not this property is set, + the bit is selected by the driver. + $ref: /schemas/types.yaml#/definitions/flag + deprecated: true + + additionalProperties: false + + required: + - reg + - nand-rb + +additionalProperties: false + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - interrupts + - clocks + +allOf: + - $ref: "nand-controller.yaml#" + + - if: + properties: + compatible: + contains: + const: marvell,pxa3xx-nand-controller + then: + required: + - dmas + - dma-names + else: + properties: + dmas: false + dma-names: false + + - if: + properties: + compatible: + contains: + const: marvell,armada-8k-nand-controller + then: + required: + - marvell,system-controller + else: + properties: + marvell,system-controller: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + nand_controller: nand-controller@d0000 { + compatible = "marvell,armada370-nand-controller"; + reg = <0xd0000 0x54>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coredivclk 0>; + + nand@0 { + reg = <0>; + label = "main-storage"; + nand-rb = <0>; + nand-ecc-mode = "hw"; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Rootfs"; + reg = <0x00000000 0x40000000>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mtd/marvell-nand.txt b/Documentation/devicetree/bindings/mtd/marvell-nand.txt deleted file mode 100644 index a2d9a0f2b683..000000000000 --- a/Documentation/devicetree/bindings/mtd/marvell-nand.txt +++ /dev/null @@ -1,126 +0,0 @@ -Marvell NAND Flash Controller (NFC) - -Required properties: -- compatible: can be one of the following: - * "marvell,armada-8k-nand-controller" - * "marvell,armada370-nand-controller" - * "marvell,pxa3xx-nand-controller" - * "marvell,armada-8k-nand" (deprecated) - * "marvell,armada370-nand" (deprecated) - * "marvell,pxa3xx-nand" (deprecated) - Compatibles marked deprecated support only the old bindings described - at the bottom. -- reg: NAND flash controller memory area. -- #address-cells: shall be set to 1. Encode the NAND CS. -- #size-cells: shall be set to 0. -- interrupts: shall define the NAND controller interrupt. -- clocks: shall reference the NAND controller clocks, the second one is - is only needed for the Armada 7K/8K SoCs -- clock-names: mandatory if there is a second clock, in this case there - should be one clock named "core" and another one named "reg" -- marvell,system-controller: Set to retrieve the syscon node that handles - NAND controller related registers (only required with the - "marvell,armada-8k-nand[-controller]" compatibles). - -Optional properties: -- label: see partition.txt. New platforms shall omit this property. -- dmas: shall reference DMA channel associated to the NAND controller. - This property is only used with "marvell,pxa3xx-nand[-controller]" - compatible strings. -- dma-names: shall be "rxtx". - This property is only used with "marvell,pxa3xx-nand[-controller]" - compatible strings. - -Optional children nodes: -Children nodes represent the available NAND chips. - -Required properties: -- reg: shall contain the native Chip Select ids (0-3). -- nand-rb: see nand-controller.yaml (0-1). - -Optional properties: -- marvell,nand-keep-config: orders the driver not to take the timings - from the core and leaving them completely untouched. Bootloader - timings will then be used. -- label: MTD name. -- nand-on-flash-bbt: see nand-controller.yaml. -- nand-ecc-mode: see nand-controller.yaml. Will use hardware ECC if not specified. -- nand-ecc-algo: see nand-controller.yaml. This property is essentially useful when - not using hardware ECC. Howerver, it may be added when using hardware - ECC for clarification but will be ignored by the driver because ECC - mode is chosen depending on the page size and the strength required by - the NAND chip. This value may be overwritten with nand-ecc-strength - property. -- nand-ecc-strength: see nand-controller.yaml. -- nand-ecc-step-size: see nand-controller.yaml. Marvell's NAND flash controller does - use fixed strength (1-bit for Hamming, 16-bit for BCH), so the actual - step size will shrink or grow in order to fit the required strength. - Step sizes are not completely random for all and follow certain - patterns described in AN-379, "Marvell SoC NFC ECC". - -See Documentation/devicetree/bindings/mtd/nand-controller.yaml for more details on -generic bindings. - - -Example: -nand_controller: nand-controller@d0000 { - compatible = "marvell,armada370-nand-controller"; - reg = <0xd0000 0x54>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&coredivclk 0>; - - nand@0 { - reg = <0>; - label = "main-storage"; - nand-rb = <0>; - nand-ecc-mode = "hw"; - marvell,nand-keep-config; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "Rootfs"; - reg = <0x00000000 0x40000000>; - }; - }; - }; -}; - - -Note on legacy bindings: One can find, in not-updated device trees, -bindings slightly different than described above with other properties -described below as well as the partitions node at the root of a so -called "nand" node (without clear controller/chip separation). - -Legacy properties: -- marvell,nand-enable-arbiter: To enable the arbiter, all boards blindly - used it, this bit was set by the bootloader for many boards and even if - it is marked reserved in several datasheets, it might be needed to set - it (otherwise it is harmless) so whether or not this property is set, - the bit is selected by the driver. -- num-cs: Number of chip-select lines to use, all boards blindly set 1 - to this and for a reason, other values would have failed. The value of - this property is ignored. - -Example: - - nand0: nand@43100000 { - compatible = "marvell,pxa3xx-nand"; - reg = <0x43100000 90>; - interrupts = <45>; - dmas = <&pdma 97 0>; - dma-names = "rxtx"; - #address-cells = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - num-cs = <1>; - /* Partitions (optional) */ - }; -- 2.17.1
