Hi, The Rockchip RK3588 Evaluation Boards use SPI connected RK806 PMICs. Downstream this is handled by a new driver, but apart from being SPI connected this chip is quite similar to the ther Rockchip PMICs (also RK806 is promoted to also support I2C). Thus this series instead updates the RK808 driver(s). Changelog since PATCHv3: * https://lore.kernel.org/all/20220909175522.179175-1-sebastian.reichel@xxxxxxxxxxxxx/ * Dropped removing REGMAP_I2C dependency from RK817 ASoC driver (applied) * Rename MFD_RK808 to MFD_RK8XX to be consistent. It makes sense to do this now, since the patchset touches all the child drivers anyways. * rebase to v6.1-rc1 * collected a couple of Acks * update rk806 DT binding according to DT maintainer feedback * add missing pinmux config to the rk806 DT binding * update rk806_spi_bus_write and rk806_spi_bus_read * replaced some constants with sizeof or defines * used capitalized comments * rename regmap_find_closest_bigger to regulator_find_closest_bigger, not sure why I prefixed it with regmap_ in the first place * use rk8xx_is_enabled_wmsk_regmap instead of regulator_is_enabled_regmap for the switching regulators to correctly report the state * reordered the first few patches grouping the MFD patches together Changelog since PATCHv2: * https://lore.kernel.org/all/20220908003107.220143-1-sebastian.reichel@xxxxxxxxxxxxx/ * Change DT binding to not allow nldo-reg6 * Fix DT binding to check for [np]ldo-reg instead of [np]ldo_reg * remove rk806_get_voltage_sel_regmap in favour of regulator_get_voltage_sel_regmap * drop rk806_set_voltage in favour of regulator_set_voltage_sel_regmap * use regulator_set_ramp_delay_regmap * drop possibly incorrect printing of chip id register address in case of errors Changelog since PATCHv1: * https://lore.kernel.org/all/20220831215437.117880-1-sebastian.reichel@xxxxxxxxxxxxx/ * Collect Acked-by * Avoid if/else checks for regulator id in rk806 regulator driver * Fix indentation in DTS example section of the rk806 binding * Use absolute path for regulator.yaml referencing in the rk806 binding * Reduce pattern for DCDC regulators to only allow 1-10 * replace uppercase name with lowercase ones in regulator names * replace _ with - in regulator names -- Sebastian Sebastian Reichel (13): clk: RK808: reduce 'struct rk808' usage regulator: rk808: reduce 'struct rk808' usage rtc: rk808: reduce 'struct rk808' usage mfd: rk808: convert to device managed resources mfd: rk808: use dev_err_probe mfd: rk808: replace 'struct i2c_client' with 'struct device' mfd: rk808: split into core and i2c dt-bindings: mfd: add rk806 binding mfd: rk8xx: add rk806 support pinctrl: rk805: add rk806 pinctrl support regulator: rk808: Use dev_err_probe regulator: expose regulator_find_closest_bigger regulator: rk808: add rk806 support .../bindings/mfd/rockchip,rk806.yaml | 405 +++++++++++++++++ drivers/clk/Kconfig | 2 +- drivers/clk/clk-rk808.c | 34 +- drivers/input/misc/Kconfig | 2 +- drivers/mfd/Kconfig | 21 +- drivers/mfd/Makefile | 4 +- drivers/mfd/{rk808.c => rk8xx-core.c} | 351 +++++---------- drivers/mfd/rk8xx-i2c.c | 209 +++++++++ drivers/mfd/rk8xx-spi.c | 115 +++++ drivers/pinctrl/Kconfig | 2 +- drivers/pinctrl/pinctrl-rk805.c | 189 +++++++- drivers/power/supply/Kconfig | 2 +- drivers/regulator/Kconfig | 2 +- drivers/regulator/helpers.c | 22 +- drivers/regulator/rk808-regulator.c | 409 ++++++++++++++++- drivers/rtc/Kconfig | 2 +- drivers/rtc/rtc-rk808.c | 47 +- include/linux/mfd/rk808.h | 417 +++++++++++++++++- include/linux/regulator/driver.h | 2 + sound/soc/codecs/Kconfig | 2 +- 20 files changed, 1913 insertions(+), 326 deletions(-) create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml rename drivers/mfd/{rk808.c => rk8xx-core.c} (70%) create mode 100644 drivers/mfd/rk8xx-i2c.c create mode 100644 drivers/mfd/rk8xx-spi.c -- 2.35.1
