On 10/14/22 3:23 AM, Apurva Nandan wrote:
J784S4 EVM board is designed for TI J784S4 SoC. It supports the following
interfaces:
* 32 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 Input Audio Jack, x1 Output Audio Jack
* x1 USB2.0 Hub with two Type A host and x1 USB 3.1 Type-C Port
* x2 4L PCIe connector
* x1 UHS-1 capable micro-SD card slot
* 512 Mbit OSPI flash, 1 Gbit Octal NAND flash, 512 Mbit QSPI flash,
UFS flash.
* x6 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* x2 ENET Expansion Connector, x1 GESI expander, x2 Display connector
* x1 15-pin CSI header
* x6 MCAN instances
Add basic support for J784S4-EVM.
Schematics: https://www.ti.com/lit/zip/sprr458
Signed-off-by: Hari Nagalla <hnagalla@xxxxxx>
Signed-off-by: Apurva Nandan <a-nandan@xxxxxx>
Signed-off-by: Nishanth Menon <nm@xxxxxx>
Signed-off-by: Matt Ranostay <mranostay@xxxxxx>
Signed-off-by: Rahul T R <r-ravikumar@xxxxxx>
Signed-off-by: Suman Anna <s-anna@xxxxxx>
Signed-off-by: Pratyush Yadav <p.yadav@xxxxxx>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@xxxxxx>
---
arch/arm64/boot/dts/ti/Makefile | 2 +
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 199 +++++++++++++++++++++++
2 files changed, 201 insertions(+)
create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 02e5d80344d0..6381c458738a 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -19,6 +19,8 @@ dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
+
dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
new file mode 100644
index 000000000000..bf2f2dfb7658
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -0,0 +1,199 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Common Processor Board: https://www.ti.com/tool/J721EXCPXEVM
This doesn't seem to be the right EVM, I'd just drop this link.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-j784s4.dtsi"
+
+/ {
+ compatible = "ti,j784s4-evm", "ti,j784s4";
+ model = "Texas Instruments J784S4 EVM";
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ aliases {
+ serial2 = &main_uart8;
+ mmc1 = &main_sdhci1;
+ i2c0 = &main_i2c0;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* 32G RAM */
+ reg = <0x00 0x80000000 0x00 0x80000000>,
+ <0x08 0x80000000 0x07 0x80000000>;
+ };
+
+ /* Reserving memory regions still pending */
Comment not needed.
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ secure_ddr: optee@9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>;
+ alignment = <0x1000>;
Is alignment needed here?
+ no-map;
+ };
+ };
+
+ evm_12v0: regulator-evm12v0 {
+ /* main supply */
+ compatible = "regulator-fixed";
+ regulator-name = "evm_12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_3v3: regulator-vsys3v3 {
+ /* Output of LM5140 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_5v0: regulator-vsys5v0 {
+ /* Output of LM5140 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_mmc1: regulator-sd {
+ /* Output of TPS22918 */
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ vin-supply = <&vsys_3v3>;
+ gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ vdd_sd_dv: regulator-TLV71033 {
+ /* Output of TLV71033 */
+ compatible = "regulator-gpio";
+ regulator-name = "tlv71033";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vdd_sd_dv_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&vsys_5v0>;
+ gpios = <&main_gpio0 8 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+};
+
+&main_pmx0 {
+ main_uart8_pins_default: main-uart8-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x040, PIN_INPUT, 14) /* (AF37) MCASP0_AXR0.UART8_CTSn */
+ J784S4_IOPAD(0x044, PIN_OUTPUT, 14) /* (AG37) MCASP0_AXR1.UART8_RTSn */
+ J784S4_IOPAD(0x0d0, PIN_INPUT, 11) /* (AP38) SPI0_CS1.UART8_RXD */
+ J784S4_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AN38) SPI0_CLK.UART8_TXD */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AN36) I2C0_SCL */
+ J784S4_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AP37) I2C0_SDA */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x104, PIN_INPUT, 0) /* (AB38) MMC1_CLK */
+ J784S4_IOPAD(0x108, PIN_INPUT, 0) /* (AB36) MMC1_CMD */
+ J784S4_IOPAD(0x100, PIN_INPUT, 0) /* (###) MMC1_CLKLB */
Pin ###?
Andrew
+ J784S4_IOPAD(0x0fc, PIN_INPUT, 0) /* (AA33) MMC1_DAT0 */
+ J784S4_IOPAD(0x0f8, PIN_INPUT, 0) /* (AB34) MMC1_DAT1 */
+ J784S4_IOPAD(0x0f4, PIN_INPUT, 0) /* (AA32) MMC1_DAT2 */
+ J784S4_IOPAD(0x0f0, PIN_INPUT, 0) /* (AC38) MMC1_DAT3 */
+ J784S4_IOPAD(0x0e8, PIN_INPUT, 8) /* (AR38) TIMER_IO0.MMC1_SDCD */
+ >;
+ };
+
+ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
+ >;
+ };
+};
+
+&main_uart8 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart8_pins_default>;
+};
+
+&main_i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+
+ clock-frequency = <400000>;
+
+ exp1: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "PCIE1_2L_MODE_SEL", "PCIE1_4L_PERSTZ", "PCIE1_2L_RC_RSTZ",
+ "PCIE1_2L_EP_RST_EN", "PCIE0_4L_MODE_SEL", "PCIE0_4L_PERSTZ",
+ "PCIE0_4L_RC_RSTZ", "PCIE0_4L_EP_RST_EN", "PCIE1_4L_PRSNT#",
+ "PCIE0_4L_PRSNT#", "CDCI1_OE1/OE4", "CDCI1_OE2/OE3",
+ "AUDIO_MUX_SEL", "EXP_MUX2", "EXP_MUX3", "GESI_EXP_PHY_RSTZ";
+ };
+
+ exp2: gpio@22 {
+ compatible = "ti,tca6424";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "R_GPIO_RGMII1_RST", "ENET2_I2CMUX_SEL", "GPIO_USD_PWR_EN",
+ "USBC_PWR_EN", "USBC_MODE_SEL1", "USBC_MODE_SEL0",
+ "GPIO_LIN_EN", "R_CAN_STB", "CTRL_PM_I2C_OE#",
+ "ENET2_EXP_PWRDN", "ENET2_EXP_SPARE2", "CDCI2_RSTZ",
+ "USB2.0_MUX_SEL", "CANUART_MUX_SEL0", "CANUART_MUX2_SEL1",
+ "CANUART_MUX1_SEL1", "ENET1_EXP_PWRDN", "ENET1_EXP_RESETZ",
+ "ENET1_I2CMUX_SEL", "ENET1_EXP_SPARE2", "ENET2_EXP_RESETZ",
+ "USER_INPUT1", "USER_LED1", "USER_LED2";
+ };
+};
+
+&main_sdhci1 {
+ /* SD card */
+ status = "okay";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ pinctrl-names = "default";
+ disable-wp;
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv>;
+};
+
+&main_gpio0 {
+ status = "okay";
+};
+
