Il 19/10/22 11:15, Biao Huang ha scritto:
Add Ethernet controller node for mt8195.
Signed-off-by: Biao Huang <biao.huang@xxxxxxxxxxxx>
---
arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 ++++++++++++++++++++
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 86 +++++++++++++++++++
2 files changed, 174 insertions(+)
..snip..
diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
index 905d1a90b406..7f7d9f8e72ee 100644
--- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
@@ -1042,6 +1042,92 @@ spis1: spi@1101e000 {
status = "disabled";
};
+ stmmac_axi_setup: stmmac-axi-config {
Didn't you get a warning during dtb build for these ones?
And if you did, why have you ignored it? :-)
+ snps,wr_osr_lmt = <0x7>;
+ snps,rd_osr_lmt = <0x7>;
+ snps,blen = <0 0 0 0 16 8 4>;
+ };
+
..snip..
+
+ eth: ethernet@11021000 {
+ compatible = "mediatek,mt8195-gmac", "snps,dwmac-5.10a";
+ reg = <0 0x11021000 0 0x4000>;
+ interrupts = <GIC_SPI 716 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "macirq";
+ clock-names = "axi",
+ "apb",
+ "mac_cg",
+ "mac_main",
+ "ptp_ref",
+ "rmii_internal";
+ clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>,
+ <&pericfg_ao CLK_PERI_AO_ETHERNET_BUS>,
+ <&pericfg_ao CLK_PERI_AO_ETHERNET_MAC>,
+ <&topckgen CLK_TOP_SNPS_ETH_250M>,
+ <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>,
+ <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>;
+ assigned-clocks = <&topckgen CLK_TOP_SNPS_ETH_250M>,
+ <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>,
+ <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>;
+ assigned-clock-parents = <&topckgen CLK_TOP_ETHPLL_D2>,
+ <&topckgen CLK_TOP_ETHPLL_D8>,
+ <&topckgen CLK_TOP_ETHPLL_D10>;
+ power-domains = <&spm MT8195_POWER_DOMAIN_ETHER>;
+ mediatek,pericfg = <&infracfg_ao>;
+ snps,axi-config = <&stmmac_axi_setup>;
+ snps,mtl-rx-config = <&mtl_rx_setup>;
+ snps,mtl-tx-config = <&mtl_tx_setup>;
+ snps,txpbl = <16>;
+ snps,rxpbl = <16>;
+ snps,clk-csr = <0>;
+ status = "disabled";
Please move stmmac-axi-config, rx-queues-config, tx-queues-config here as a subnode
or in the root node, respecting address/size cells being zero.
Of course adding that here means also specifying {address,size}-cells = <0> in this
ethernet node.
Regards,
Angelo
