> Subject: Re: [PATCH 1/6] dt-bindings: usb: ci-hdrc-usb2: convert to yaml > > On Mon, Oct 10, 2022 at 06:18:11PM +0800, Peng Fan (OSS) wrote: > > From: Peng Fan <peng.fan@xxxxxxx> > > > > Convert the binding to yaml format > > s/yaml/DT schema/ > > > > > Signed-off-by: Peng Fan <peng.fan@xxxxxxx> > > --- > > .../devicetree/bindings/usb/ci-hdrc-usb2.txt | 158 --------- > > .../devicetree/bindings/usb/ci-hdrc-usb2.yaml | 306 ++++++++++++++++++ > > 2 files changed, 306 insertions(+), 158 deletions(-) delete mode > > 100644 Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt > > create mode 100644 > > Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml > > > diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml > > b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml > > new file mode 100644 > > index 000000000000..1c10691c45f2 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.yaml > > @@ -0,0 +1,306 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) %YAML 1.2 > > +--- > > +$id: > > > +https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fdevi > > +cetree.org%2Fschemas%2Fusb%2Fci-hdrc- > usb2.yaml%23&data=05%7C01%7C > > > +peng.fan%40nxp.com%7Cfc258d6827034e160b4908daaab8b693%7C686ea > 1d3bc2b4 > > > +c6fa92cd99c5c301635%7C0%7C0%7C638010007567431723%7CUnknown% > 7CTWFpbGZs > > > +b3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6 > Mn0%3 > > > +D%7C3000%7C%7C%7C&sdata=g%2FCjkGDjScTAOc1PQg1BI9GjC%2Fg > XRK5DuyHcT > > +NjLCZQ%3D&reserved=0 > > +$schema: > > > +https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Fdevi > > +cetree.org%2Fmeta- > schemas%2Fcore.yaml%23&data=05%7C01%7Cpeng.fan% > > > +40nxp.com%7Cfc258d6827034e160b4908daaab8b693%7C686ea1d3bc2b4c > 6fa92cd9 > > > +9c5c301635%7C0%7C0%7C638010007567431723%7CUnknown%7CTWFpb > GZsb3d8eyJWI > > > +joiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7 > C3000% > > > +7C%7C%7C&sdata=s61yrkTxGglHJ7d9oL8WGD7fQYMeDDnZHi21c6Wg > %2B6k%3D&a > > +mp;reserved=0 > > + > > +title: USB2 ChipIdea USB controller for ci13xxx Binding > > + > > +maintainers: > > + - Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx> > > + > > +properties: > > + compatible: > > + oneOf: > > + - enum: > > + - chipidea,usb2 > > + - lsi,zevio-usb > > + - nvidia,tegra20-udc > > + - nvidia,tegra30-udc > > + - nvidia,tegra114-udc > > + - nvidia,tegra124-udc > > + - qcom,ci-hdrc > > + - items: > > + - enum: > > + - fsl,imx23-usb > > + - fsl,imx25-usb > > + - fsl,imx28-usb > > + - fsl,imx6q-usb > > + - fsl,imx6sl-usb > > + - fsl,imx6sx-usb > > + - fsl,imx6ul-usb > > + - fsl,imx7d-usb > > + - const: fsl,imx27-usb > > + - items: > > + - const: fsl,imx7ulp-usb > > + - const: fsl,imx6ul-usb > > + - items: > > + - const: lsi,zevio-usb > > + - items: > > + - const: xlnx,zynq-usb-2.20a > > + - const: chipidea,usb2 > > + reg: > > + maxItems: 1 > > + > > + interrupts: > > + maxItems: 1 > > + > > + clocks: > > + maxItems: 2 > > + > > + itc-setting: > > + description: > > + interrupt threshold control register control, the setting should be > > + aligned with ITC bits at register USBCMD. > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + > > + ahb-burst-config: > > + description: > > + it is vendor dependent, the required value should be aligned with > > + AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is > > + used to change AHB burst configuration, check the chipidea spec for > > + meaning of each value. If this property is not existed, it will use > > + the reset value. > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0x0 > > + maximum: 0x7 > > + > > + tx-burst-size-dword: > > + description: > > + it is vendor dependent, the tx burst size in dword (4 bytes), This > > + register represents the maximum length of a the burst in 32-bit > > + words while moving data from system memory to the USB bus, the > value > > + of this property will only take effect if property "ahb-burst-config" > > + is set to 0, if this property is missing the reset default of the > > + hardware implementation will be used. > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + > > + rx-burst-size-dword: > > + description: > > + it is vendor dependent, the rx burst size in dword (4 bytes), This > > + register represents the maximum length of a the burst in 32-bit words > > + while moving data from the USB bus to system memory, the value of > > + this property will only take effect if property "ahb-burst-config" > > + is set to 0, if this property is missing the reset default of the > > + hardware implementation will be used. > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + > > + extcon: > > + description: | > > + Phandles to external connector devices. First phandle should point > > + to external connector, which provide "USB" cable events, the second > > + should point to external connector device, which provide "USB-HOST" > > + cable events. If one of the external connector devices is not > > + required, empty <0> phandle should be specified. > > + > > + phy-clkgate-delay-us: > > + description: | > > + The delay time (us) between putting the PHY into low power mode > and > > + gating the PHY clock. > > + > > + non-zero-ttctrl-ttha: > > + description: | > > + After setting this property, the value of register ttctrl.ttha > > + will be 0x7f; if not, the value will be 0x0, this is the default > > + value. It needs to be very carefully for setting this property, it > > + is recommended that consult with your IC engineer before setting > > + this value. On the most of chipidea platforms, the "usage_tt" flag > > + at RTL is 0, so this property only affects siTD. > > + > > + If this property is not set, the max packet size is 1023 bytes, and > > + if the total of packet size for pervious transactions are more than > > + 256 bytes, it can't accept any transactions within this frame. The > > + use case is single transaction, but higher frame rate. > > + > > + If this property is set, the max packet size is 188 bytes, it can > > + handle more transactions than above case, it can accept transactions > > + until it considers the left room size within frame is less than 188 > > + bytes, software needs to make sure it does not send more than 90% > > + maximum_periodic_data_per_frame. The use case is multiple > > + transactions, but less frame rate. > > + > > + mux-controls: > > + description: | > > + The mux control for toggling host/device output of this controller. > > + It's expected that a mux state of 0 indicates device mode and a mux > > + state of 1 indicates host mode. > > + > > + mux-control-names: > > + description: Shall be "usb_switch" if mux-controls is specified. > > + > > + pinctrl-names: > > + description: | > > + Names for optional pin modes in "default", "host", "device". > > + In case of HSIC-mode, "idle" and "active" pin modes are mandatory. > > + In this case, the "idle" state needs to pull down the data and > > + strobe pin and the "active" state needs to pull up the strobe pin. > > + > > + pinctrl-0: > > + maxItems: 1 > > + > > + pinctrl-1: > > + maxItems: 1 > > + > > + phys: > > + maxItems: 1 > > + > > + phy-names: > > + const: usb-phy > > + > > + vbus-supply: > > + description: reference to the VBUS regulator. > > + > > +required: > > + - compatible > > + - reg > > + - interrupts > > + > > +allOf: > > + - $ref: usb-drd.yaml# > > + - $ref: usb-hcd.yaml# > > + - if: > > + properties: > > + mux-controls: > > + true > > + then: > > + properties: > > + mux-control-names: > > + const: usb_switch > > + - if: > > + properties: > > + phy_type: > > + const: hsic > > + > > + required: > > + - phy_type > > + then: > > + properties: > > + pinctrl-names: > > + items: > > + - const: idle > > + - const: active > > + else: > > + properties: > > + pinctrl-names: > > + oneOf: > > + - items: > > + - const: default > > + - enum: > > + - host > > + - device > > + - items: > > + - const: default > > + - if: > > + properties: > > + compatible: > > + enum: > > + - fsl,imx23-usb > > + - fsl,imx25-usb > > + - fsl,imx27-usb > > + - fsl,imx28-usb > > + - fsl,imx6q-usb > > + - fsl,imx6sl-usb > > + - fsl,imx6sx-usb > > + - fsl,imx6ul-usb > > + - fsl,imx7d-usb > > + - fsl,imx7ulp-usb > > + then: > > + properties: > > + fsl,usbmisc: > > + description: > > + Phandler of non-core register device, with one argument that > > + indicate usb controller index > > type ref? > > Don't define properties within if/then/else. Define at top level and then > restrict presence in the if/then schema. > > > + > > + disable-over-current: > > + description: disable over current detect > > + > > + over-current-active-low: > > + description: over current signal polarity is active low > > + > > + over-current-active-high: > > + description: | > > + Over current signal polarity is active high. It's recommended to > > + specify the over current polarity. > > + > > + power-active-high: > > + description: power signal polarity is active high > > + > > + external-vbus-divider: > > + description: enables off-chip resistor divider for Vbus > > + > > + samsung,picophy-pre-emp-curr-control: > > + description: | > > + HS Transmitter Pre-Emphasis Current Control. This signal controls > > + the amount of current sourced to the USB_OTG*_DP and > USB_OTG*_DN > > + pins after a J-to-K or K-to-J transition. The range is from 0x0 to > > + 0x3, the default value is 0x1. Details can refer to > TXPREEMPAMPTUNE0 > > + bits of USBNC_n_PHY_CFG1. > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0x0 > > + maximum: 0x3 > > + > > + samsung,picophy-dc-vol-level-adjust: > > + description: | > > + HS DC Voltage Level Adjustment. Adjust the high-speed transmitter > DC > > + level voltage. The range is from 0x0 to 0xf, the default value is > > + 0x3. Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1. > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0x0 > > + maximum: 0xf > > + > > +additionalProperties: true > > Cannot be true. > > > + > > +examples: > > + - | > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/clock/berlin2.h> > > + > > + usb@f7ed0000 { > > + compatible = "chipidea,usb2"; > > Doesn't match documentation. You should know by now to test your > bindings. I am not very clear on this. Could you please share more info? Thanks, Peng. > > > + reg = <0xf7ed0000 0x10000>; > > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&chip CLKID_USB0>; > > + phys = <&usb_phy0>; > > + phy-names = "usb-phy"; > > + vbus-supply = <®_usb0_vbus>; > > + itc-setting = <0x4>; /* 4 micro-frames */ > > + /* Incremental burst of unspecified length */ > > + ahb-burst-config = <0x0>; > > + tx-burst-size-dword = <0x10>; /* 64 bytes */ > > + rx-burst-size-dword = <0x10>; > > + extcon = <0>, <&usb_id>; > > + phy-clkgate-delay-us = <400>; > > + mux-controls = <&usb_switch>; > > + mux-control-names = "usb_switch"; > > + }; > > + > > + # Example for HSIC: > > + - | > > + #include <dt-bindings/interrupt-controller/arm-gic.h> > > + #include <dt-bindings/clock/imx6qdl-clock.h> > > + > > + usb@2184400 { > > + compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; > > + reg = <0x02184400 0x200>; > > + interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6QDL_CLK_USBOH3>; > > + fsl,usbphy = <&usbphynop1>; > > + fsl,usbmisc = <&usbmisc 2>; > > + phy_type = "hsic"; > > + dr_mode = "host"; > > + ahb-burst-config = <0x0>; > > + tx-burst-size-dword = <0x10>; > > + rx-burst-size-dword = <0x10>; > > + pinctrl-names = "idle", "active"; > > + pinctrl-0 = <&pinctrl_usbh2_idle>; > > + pinctrl-1 = <&pinctrl_usbh2_active>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + usbnet: ethernet@1 { > > + compatible = "usb424,9730"; > > + reg = <1>; > > + }; > > + }; > > + > > +... > > -- > > 2.37.1 > > > >
