During every transfer GQSPI driver writes the CPOL & CPHA values to the configuration register. But the CPOL & CPHA values do not change in between multiple transfers, so moved the CPOL & CPHA initialization to hardware init so that the values are written only once. Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xxxxxxx> --- drivers/spi/spi-zynqmp-gqspi.c | 32 +++++++++++++++++--------------- 1 file changed, 17 insertions(+), 15 deletions(-) diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c index 973008a30a09..1b56dd29057f 100644 --- a/drivers/spi/spi-zynqmp-gqspi.c +++ b/drivers/spi/spi-zynqmp-gqspi.c @@ -266,7 +266,9 @@ static void zynqmp_gqspi_selectslave(struct zynqmp_qspi *instanceptr, * - Enable manual slave select * - Enable manual start * - Deselect all the chip select lines - * - Set the little endian mode of TX FIFO and + * - Set the little endian mode of TX FIFO + * - Set clock phase + * - Set clock polarity and * - Enable the QSPI controller */ static void zynqmp_qspi_init_hw(struct zynqmp_qspi *xqspi) @@ -305,10 +307,17 @@ static void zynqmp_qspi_init_hw(struct zynqmp_qspi *xqspi) config_reg |= GQSPI_CFG_WP_HOLD_MASK; /* Clear pre-scalar by default */ config_reg &= ~GQSPI_CFG_BAUD_RATE_DIV_MASK; - /* CPHA 0 */ - config_reg &= ~GQSPI_CFG_CLK_PHA_MASK; - /* CPOL 0 */ - config_reg &= ~GQSPI_CFG_CLK_POL_MASK; + /* Set CPHA */ + if (xqspi->ctlr->mode_bits & SPI_CPHA) + config_reg |= GQSPI_CFG_CLK_PHA_MASK; + else + config_reg &= ~GQSPI_CFG_CLK_PHA_MASK; + /* Set CPOL */ + if (xqspi->ctlr->mode_bits & SPI_CPOL) + config_reg |= GQSPI_CFG_CLK_POL_MASK; + else + config_reg &= ~GQSPI_CFG_CLK_POL_MASK; + zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg); /* Clear the TX and RX FIFO */ @@ -470,14 +479,6 @@ static int zynqmp_qspi_config_op(struct zynqmp_qspi *xqspi, config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST); - /* Set the QSPI clock phase and clock polarity */ - config_reg &= (~GQSPI_CFG_CLK_PHA_MASK) & (~GQSPI_CFG_CLK_POL_MASK); - - if (qspi->mode & SPI_CPHA) - config_reg |= GQSPI_CFG_CLK_PHA_MASK; - if (qspi->mode & SPI_CPOL) - config_reg |= GQSPI_CFG_CLK_POL_MASK; - config_reg &= ~GQSPI_CFG_BAUD_RATE_DIV_MASK; config_reg |= (baud_rate_val << GQSPI_CFG_BAUD_RATE_DIV_SHIFT); zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg); @@ -1170,6 +1171,9 @@ static int zynqmp_qspi_probe(struct platform_device *pdev) goto clk_dis_all; } + ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD | + SPI_TX_DUAL | SPI_TX_QUAD; + /* QSPI controller initializations */ zynqmp_qspi_init_hw(xqspi); @@ -1207,8 +1211,6 @@ static int zynqmp_qspi_probe(struct platform_device *pdev) ctlr->setup = zynqmp_qspi_setup_op; ctlr->max_speed_hz = clk_get_rate(xqspi->refclk) / 2; ctlr->bits_per_word_mask = SPI_BPW_MASK(8); - ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD | - SPI_TX_DUAL | SPI_TX_QUAD; ctlr->dev.of_node = np; ctlr->auto_runtime_pm = true; -- 2.17.1
