On 06/10/2022 13:08, Amjad Ouled-Ameur wrote:
Hi Daniel,
Thank you for your feedback.
On 10/4/22 12:47, Daniel Lezcano wrote:
Hi Amjad,
On 04/10/2022 12:11, Amjad Ouled-Ameur wrote:
Thermal zones without trip point are not registered by thermal core.
tzts1 ~ tzts6 zones of mt8183 were intially introduced for test-purpose
only.
Disable the zones above and keep only cpu_thermal enabled.
It does not make sense to disable the thermal zones. Either the
thermal zones are needed or they are not. Keeping them for debug
purpose is not desired.
As Matthias Brugger mentioned in previous versions, DTS should describe
the HW as it is, the sensors are in the HW.
Yes, it is here:
thermal: thermal@1100b000 {
#thermal-sensor-cells = <1>;
compatible = "mediatek,mt8183-thermal";
reg = <0 0x1100b000 0 0x1000>;
clocks = <&infracfg CLK_INFRA_THERM>,
<&infracfg CLK_INFRA_AUXADC>;
clock-names = "therm", "auxadc";
resets = <&infracfg
MT8183_INFRACFG_AO_THERM_SW_RST>;
interrupts = <0 76 IRQ_TYPE_LEVEL_LOW>;
mediatek,auxadc = <&auxadc>;
mediatek,apmixedsys = <&apmixedsys>;
nvmem-cells = <&thermal_calibration>;
nvmem-cell-names = "calibration-data";
};
Alternatively to removal, you can:
- remove 'sustainable-power'
- add a passive trip point, optionally a hot trip point and a
critical trip point
Why removing "sustainable-power" instead of simply disabling the device
?
Because sustainable-power is wrong. It is probably coming from a
copy-paste. It does not make sense to have this.
The sustainable-power is for the power allocator governor which is
limited to CPU and GPU. Here the thermal zones are for different devices.
Especially that, if a user needs to use the sensor
If the thermal zone is disabled, how can it use the sensor?
in the future, they might not be able to find the right
sustainable-power ; thus I think it should remain the way it is.
As to adding tripping points, MediaTek does not have ones to add for now
for those sensors.
Please do this:
Add:
trips {
threshold : trip1 {
temperature = <50000>;
type = "passive";
};
};
And remove all the empty cooling maps and the sustainable power properties.
The passive trip point will allow the userspace to set a value in
order to get notified about the devices temperature (writable trip
point). The hot temperature will send a notification to userspace so
it can take a last chance decision to drop the temperature before the
critical temperature.
The passive trip point temperature could be a high temperature.
The mitigation is also managed from userspace as a whole.
Signed-off-by: Amjad Ouled-Ameur <aouledameur@xxxxxxxxxxxx>
---
arch/arm64/boot/dts/mediatek/mt8183.dtsi | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
index 9d32871973a2..53f7a0fbaa88 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -1191,6 +1191,7 @@ tzts1: tzts1 {
polling-delay = <0>;
thermal-sensors = <&thermal 1>;
sustainable-power = <5000>;
+ status = "disabled";
trips {};
cooling-maps {};
};
@@ -1200,6 +1201,7 @@ tzts2: tzts2 {
polling-delay = <0>;
thermal-sensors = <&thermal 2>;
sustainable-power = <5000>;
+ status = "disabled";
trips {};
cooling-maps {};
};
@@ -1209,6 +1211,7 @@ tzts3: tzts3 {
polling-delay = <0>;
thermal-sensors = <&thermal 3>;
sustainable-power = <5000>;
+ status = "disabled";
trips {};
cooling-maps {};
};
@@ -1218,6 +1221,7 @@ tzts4: tzts4 {
polling-delay = <0>;
thermal-sensors = <&thermal 4>;
sustainable-power = <5000>;
+ status = "disabled";
trips {};
cooling-maps {};
};
@@ -1227,6 +1231,7 @@ tzts5: tzts5 {
polling-delay = <0>;
thermal-sensors = <&thermal 5>;
sustainable-power = <5000>;
+ status = "disabled";
trips {};
cooling-maps {};
};
@@ -1236,6 +1241,7 @@ tztsABB: tztsABB {
polling-delay = <0>;
thermal-sensors = <&thermal 6>;
sustainable-power = <5000>;
+ status = "disabled";
trips {};
cooling-maps {};
};
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
