Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.
Specification:
- Processor Marvell 88F6702 1 GHz
- 256MB RAM
- 128MB NAND
- 1x GBE LAN port (PHY: Marvell 88E1318)
- 2x USB 2.0
- 1x SATA
- 3x button
- 7x leds
- serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)
Tested-by: Tony Dinh <mibodhi@xxxxxxxxx>
Signed-off-by: Pawel Dembicki <paweldembicki@xxxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/kirkwood-nsa310s.dts | 267 +++++++++++++++++++++++++
2 files changed, 268 insertions(+)
create mode 100644 arch/arm/boot/dts/kirkwood-nsa310s.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 05d8aef6e5d2..eae7d1139fbc 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -354,6 +354,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-ns2mini.dtb \
kirkwood-nsa310.dtb \
kirkwood-nsa310a.dtb \
+ kirkwood-nsa310s.dtb \
kirkwood-nsa320.dtb \
kirkwood-nsa325.dtb \
kirkwood-openblocks_a6.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-nsa310s.dts b/arch/arm/boot/dts/kirkwood-nsa310s.dts
new file mode 100644
index 000000000000..210dfdb577bb
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
@@ -0,0 +1,267 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ZyXEL NSA310S Board Description
+ * Copyright 2020-2022 Pawel Dembicki <paweldembicki@xxxxxxxxx>
+ * Copyright (c) 2015-2021, Tony Dinh <mibodhi@xxxxxxxxx>
+ * Copyright (c) 2014, Adam Baker <linux@xxxxxxxxxxxxxxxx>
+ * Based upon the board setup file created by Peter Schildmann
+ */
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "ZyXEL NSA310S";
+ compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ gpio_poweroff {
+ compatible = "gpio-poweroff";
+ pinctrl-0 = <&pmx_pwr_off>;
+ pinctrl-names = "default";
+ gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_buttons>;
+ pinctrl-names = "default";
+
+ power {
+ label = "Power Button";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ copy {
+ label = "Copy Button";
+ linux,code = <KEY_COPY>;
+ gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_leds>;
+ pinctrl-names = "default";
+
+ led-1 {
+ function = LED_FUNCTION_DISK_ERR;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-2 {
+ function = LED_FUNCTION_USB;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "usb-host";
+ };
+
+ led-3 {
+ function = LED_FUNCTION_DISK;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "ata1";
+ };
+
+ led-4 {
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-5 {
+ function = LED_FUNCTION_INDICATOR;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-6 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ led-7 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_power>;
+ pinctrl-names = "default";
+
+ usb0_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ sata1_power: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "SATA1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ thermal-zones {
+ disk-thermal {
+ polling-delay = <20000>;
+ polling-delay-passive = <2000>;
+
+ thermal-sensors = <&hdd_temp>;
+
+ trips {
+ disk_alert: disk-alert {
+ temperature = <40000>;
+ hysteresis = <5000>;
+ type = "active";
+ };
+ disk_crit: disk-crit {
+ temperature = <60000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
+
+ð0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ phy-handle = <ðphy0>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ rtc@68 {
+ compatible = "htk,ht1382";
+ reg = <0x68>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@1 {
+ reg = <1>;
+ phy-mode = "rgmii-id";
+ marvell,reg-init = <0x1 0x16 0x0 0x3>,
+ <0x1 0x10 0x0 0x1017>,
+ <0x1 0x11 0x0 0x4408>,
+ <0x1 0x16 0x0 0x0>;
+ };
+};
+
+&nand {
+ status = "okay";
+ chip-delay = <35>;
+
+ partition@0 {
+ label = "uboot";
+ reg = <0x0000000 0x00c0000>;
+ read-only;
+ };
+ partition@c0000 {
+ label = "uboot_env";
+ reg = <0x00c0000 0x0080000>;
+ };
+ partition@140000 {
+ label = "ubi";
+ reg = <0x0140000 0x7ec0000>;
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+
+ pmx_buttons: pmx-buttons {
+ marvell,pins = "mpp24", "mpp25", "mpp26";
+ marvell,function = "gpio";
+ };
+
+ pmx_leds: pmx-leds {
+ marvell,pins = "mpp13", "mpp15", "mpp16", "mpp22", "mpp23",
+ "mpp28", "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_power: pmx-power {
+ marvell,pins = "mpp21", "mpp33";
+ marvell,function = "gpio";
+ };
+
+ pmx_pwr_off: pmx-pwr-off {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+};
+
+&rtc {
+ status = "disabled";
+};
+
+&sata {
+ status = "okay";
+ nr-ports = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdd_temp: sata-port@0 {
+ reg = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
--
2.34.1
