Re: [RFC PATCH 00/10] thermal/drivers/tsens: specify nvmem cells in DT rather than parsing them manually

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Dmitry,

On Sat, Sep 10, 2022 at 03:46:51PM +0300, Dmitry Baryshkov wrote:
> Historically the tsens driver fetches the calibration data as a blob and
> then parses the blob on its own. This results in semi-duplicated code
> spreading over the platform-specific functions.
> 
> This patch series changes tsens calibration code to use pre-parsed nvmem
> cells rather than parsing the blob in the driver. For backwards
> compatibility the old code is left in place for msm8916 and qcs404, two
> platforms which have in-tree DT files. For msm8974 the original function
> is left intact, since it differs significantly (and I can not test the
> code on msm8974). For all other affected platforms the old parsing code
> has been dropped as a part of this RFC.
> 
> The code was tested on msm8916 and qcs404 only, thus it is being sent as
> an RFC.
> 

Thanks a lot for working on this!

After thinking about this for a while I wonder if we can go even a step
further: Can we drop SoC-specific code entirely for 8939 and 9607 and
match the generic compatible (qcom,tsens-v0_1)? This would allow most
v0.1 plaforms to use generic code like for qcom,tsens-v2.

AFAICT with your changes only the following remains SoC-specific:

  - hw_ids (actually only needed for 8939 since 9607 has standard IDs)

While two other things are already handled:

  - num_sensors (the driver supports "#qcom,sensors" in DT already)
  - tsens_calibrate_nvmem() shift (AFAICT in downstream msm-tsens.c
    everything except 8916 uses shift = 2. 8916 needs special handling
    anyway for the backwards compatibility)

Having the generic compatible would allow me to add MSM8909 without any
code changes at all (just DT schema addition).

For 8939 we could read the hw_ids from the DT with something like:

	qcom,sensors = <0 1 2 3 5 6 7 8 9 10>;

And actually there are two revisions of 8939, the older one has one
sensor less (msm-3.10: msm8939-common.dtsi vs msm8939-v3.0.dtsi).
This could also be easily handled from the DT without any code changes:

	qcom,sensors = <0 1 2 3 5 6 7 8 9>;

The diff could be something like the following (I did not test it yet).

What do you think?

Thanks,
Stephan

 drivers/thermal/qcom/tsens-v0_1.c | 32 +++++---------------------------
 drivers/thermal/qcom/tsens.c      | 27 ++++++++++++++++++---------
 drivers/thermal/qcom/tsens.h      |  2 +-
 3 files changed, 24 insertions(+), 37 deletions(-)

diff --git a/drivers/thermal/qcom/tsens-v0_1.c b/drivers/thermal/qcom/tsens-v0_1.c
index c3613b7ccc19..8bfa85b31146 100644
--- a/drivers/thermal/qcom/tsens-v0_1.c
+++ b/drivers/thermal/qcom/tsens-v0_1.c
@@ -194,11 +194,6 @@ static int calibrate_8916(struct tsens_priv *priv)
 	return 0;
 }
 
-static int calibrate_8939(struct tsens_priv *priv)
-{
-	return tsens_calibrate_nvmem(priv, 2);
-}
-
 static int calibrate_8974(struct tsens_priv *priv)
 {
 	int base1 = 0, base2 = 0, i;
@@ -335,7 +330,7 @@ static int calibrate_8974(struct tsens_priv *priv)
 	return 0;
 }
 
-static int calibrate_9607(struct tsens_priv *priv)
+static int calibrate_dt(struct tsens_priv *priv)
 {
 	return tsens_calibrate_nvmem(priv, 2);
 }
@@ -401,21 +396,6 @@ struct tsens_plat_data data_8916 = {
 	.fields	= tsens_v0_1_regfields,
 };
 
-static const struct tsens_ops ops_8939 = {
-	.init		= init_common,
-	.calibrate	= calibrate_8939,
-	.get_temp	= get_temp_common,
-};
-
-struct tsens_plat_data data_8939 = {
-	.num_sensors	= 10,
-	.ops		= &ops_8939,
-	.hw_ids		= (unsigned int []){ 0, 1, 2, 4, 5, 6, 7, 8, 9, 10 },
-
-	.feat		= &tsens_v0_1_feat,
-	.fields	= tsens_v0_1_regfields,
-};
-
 static const struct tsens_ops ops_8974 = {
 	.init		= init_common,
 	.calibrate	= calibrate_8974,
@@ -429,16 +409,14 @@ struct tsens_plat_data data_8974 = {
 	.fields	= tsens_v0_1_regfields,
 };
 
-static const struct tsens_ops ops_9607 = {
+static const struct tsens_ops ops_generic_v0_1 = {
 	.init		= init_common,
-	.calibrate	= calibrate_9607,
+	.calibrate	= calibrate_dt,
 	.get_temp	= get_temp_common,
 };
 
-struct tsens_plat_data data_9607 = {
-	.num_sensors	= 5,
-	.ops		= &ops_9607,
-	.hw_ids		= (unsigned int []){ 0, 1, 2, 3, 4 },
+struct tsens_plat_data data_tsens_v0_1 = {
+	.ops		= &ops_generic_v0_1
 	.feat		= &tsens_v0_1_feat,
 	.fields	= tsens_v0_1_regfields,
 };
diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
index e69134a6419a..c4772962fb94 100644
--- a/drivers/thermal/qcom/tsens.c
+++ b/drivers/thermal/qcom/tsens.c
@@ -1021,15 +1021,9 @@ static const struct of_device_id tsens_table[] = {
 	{
 		.compatible = "qcom,ipq8064-tsens",
 		.data = &data_8960,
-	}, {
-		.compatible = "qcom,mdm9607-tsens",
-		.data = &data_9607,
 	}, {
 		.compatible = "qcom,msm8916-tsens",
 		.data = &data_8916,
-	}, {
-		.compatible = "qcom,msm8939-tsens",
-		.data = &data_8939,
 	}, {
 		.compatible = "qcom,msm8960-tsens",
 		.data = &data_8960,
@@ -1042,6 +1036,9 @@ static const struct of_device_id tsens_table[] = {
 	}, {
 		.compatible = "qcom,msm8996-tsens",
 		.data = &data_8996,
+	}, {
+		.compatible = "qcom,tsens-v0_1",
+		.data = &data_tsens_v0_1,
 	}, {
 		.compatible = "qcom,tsens-v1",
 		.data = &data_tsens_v1,
@@ -1152,6 +1149,8 @@ static int tsens_probe(struct platform_device *pdev)
 	struct tsens_priv *priv;
 	const struct tsens_plat_data *data;
 	const struct of_device_id *id;
+	unsigned int *hw_ids;
+	unsigned int dt_hw_ids[MAX_SENSORS];
 	u32 num_sensors;
 
 	if (pdev->dev.of_node)
@@ -1168,10 +1167,20 @@ static int tsens_probe(struct platform_device *pdev)
 		data = &data_8960;
 
 	num_sensors = data->num_sensors;
+	hw_ids = data->hw_ids;
 
-	if (np)
+	if (np) {
 		of_property_read_u32(np, "#qcom,sensors", &num_sensors);
 
+		ret = of_property_read_variable_u32_array(np, "qcom,sensors",
+							  dt_hw_ids,
+							  1, MAX_SENSORS);
+		if (ret > 0) {
+			hw_ids = dt_hw_ids;
+			num_sensors = ret;
+		}
+	}
+
 	if (num_sensors <= 0) {
 		dev_err(dev, "%s: invalid number of sensors\n", __func__);
 		return -EINVAL;
@@ -1187,8 +1196,8 @@ static int tsens_probe(struct platform_device *pdev)
 	priv->num_sensors = num_sensors;
 	priv->ops = data->ops;
 	for (i = 0;  i < priv->num_sensors; i++) {
-		if (data->hw_ids)
-			priv->sensor[i].hw_id = data->hw_ids[i];
+		if (hw_ids)
+			priv->sensor[i].hw_id = hw_ids[i];
 		else
 			priv->sensor[i].hw_id = i;
 	}
diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
index 504ed3394a79..439f356f0177 100644
--- a/drivers/thermal/qcom/tsens.h
+++ b/drivers/thermal/qcom/tsens.h
@@ -589,7 +589,7 @@ int get_temp_common(const struct tsens_sensor *s, int *temp);
 extern struct tsens_plat_data data_8960;
 
 /* TSENS v0.1 targets */
-extern struct tsens_plat_data data_8916, data_8939, data_8974, data_9607;
+extern struct tsens_plat_data data_8916, data_8974, data_tsens_v0_1;
 
 /* TSENS v1 targets */
 extern struct tsens_plat_data data_tsens_v1, data_8976;



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux